71773b128d
Fix stepper use before init. Add Ultimaker2+ Extended clone config ( #13284 )
6 years ago
edc4e037c4
Add a note to G10
6 years ago
57afd0ab37
Fix range check bug in FileList::seek() ( #13286 )
...
When `count()` returns 0, `pos > (count()-1)` will always yield `true` due to integer underflow.
6 years ago
05c2f80826
Fix bug in wait-for-heatup ( #13290 )
6 years ago
b0553d2d97
Add M997 support and simple implementation for LPC176x ( #13281 )
6 years ago
fa236e9718
General cleanup ahead of L64XX
6 years ago
2f1e1dcb42
Gradual step towards EXTRUDERS 0 support
6 years ago
99d0022fae
Drop the Z_MIN_PROBE_ENDSTOP option ( #13276 )
6 years ago
9a6b90f47d
TMC2660.h comment tweaks
6 years ago
a2e3226597
Init XYZ to configured home position
6 years ago
4fbbce9a35
Marlin Dev Mode for DOGM status screen
6 years ago
e2e2a55d9b
Add thermistor type 67 SliceEng ( #13275 )
6 years ago
5b7ad3a5a0
Fix SKR onboard TF card CS pin ( #13272 )
6 years ago
7fde3ed915
Skip hysteresis check when temp is already close to target
...
To eliminate a long delay during pause, park, and filament change
6 years ago
7de6476b3d
Fix binary protocol error
6 years ago
2c10222e87
card.transfer_port => transfer_port_index
6 years ago
4ab433d391
Fix binary protocol with one serial port ( #13270 )
...
- The `sdcard.transfer_port` variable is Marlin's internal serial port index, not the physical serial port number.
- Added packet number to "ok" response so hosts don't need to wait for the ACK.
- Renamed feature to `BINARY_FILE_TRANSFER`, as the speed up is only consequential to the ability to transfer binaries over serial.
6 years ago
eb4bf93ea4
Add more Babystep options ( #13262 )
6 years ago
f37df28d17
UBL G29 T current position fix
...
Counterpart to #12845
6 years ago
f8a39919fa
Add Bigtree SKR 1.3 board ( #13267 )
...
Co-Authored-By: Msq001 <msq001@users.noreply.github.com>
6 years ago
ddbe4cfa20
Printrboard G2 support ( #13116 )
6 years ago
4200f9ed62
Hide freeMemory et.al. warnings
6 years ago
dc88747770
Fix Due GET_ARRAY_IS_DIGITAL
...
Co-Authored-By: bob-the-kuhn <bob.kuhn@att.net>
6 years ago
a79b9bbe6b
Cleanup whitespace, add a const
6 years ago
2616e4d4d9
Remove duplicated 'chitchat' defines ( #13258 )
6 years ago
5d28575d4d
Clean up some motion code
6 years ago
808b076000
Update some ABL/UBL conditionals
6 years ago
833c2e54a1
Add an empty flushTX to MarlinSerialUSB_Due
6 years ago
38363902c7
Fix sanity checks for distinct E factor settings
...
Reference #13156
6 years ago
64253e1a58
Followup to serial reform
...
Reference #13250
6 years ago
92a4984066
Fix G34 probe position ( #13251 )
6 years ago
e15354e387
Simplify serial port redirect ( #13234 )
6 years ago
88cc1d1a31
Fix Preprocessor syntax in Re-ARM pins file ( #13247 )
6 years ago
76e9ee33aa
Fix include order to make SERIAL_PORT_2 work ( #13241 )
6 years ago
562f2321d2
Fix a G34 bug, allow negative Z corrections ( #13240 )
6 years ago
edf025ed8d
Update Spanish language ( #13236 )
6 years ago
02fec89a0d
Turn fans off in zero_fan_speeds
...
Addressing #13231
6 years ago
15aa932aa6
HAL for Linux ( #13146 )
6 years ago
5eb82ca6a8
Change SSD1306_OLED_I2C_CONTROLLER to HAS_SSD1306_OLED_I2C ( #13223 )
6 years ago
109e67169c
Define G21 as NOOP w/o INCH_MODE_SUPPORT ( #13229 )
...
Ticket #13228
If `INCH_MODE_SUPPORT` is undefined, G20 is an unknown command as it should be (Marlin is, by default, operating in metric mode). G21, however, is found in many slicers and printer start gcode sections and should be accepted (as a NOOP) to avoid the unknown commands.
6 years ago
31b0be74af
Fix autotemp_factor menu setting ( #13226 )
...
Fix #12643
Only factors above 1 can have a 'positive' effect.
6 years ago
f6ab62bc13
Fix Creality CR-10 S5 filament change ( #13219 )
6 years ago
9f5e4e5ad8
Update LPC1769 Pins Files ( #13183 )
6 years ago
608a6810e7
Fix DOGLCD_A0 pin in pins_Smoothieboard.h ( #13217 )
6 years ago
80359c9937
Add more parameters to M240
...
Co-Authored-By: shitcreek <45380455+shitcreek@users.noreply.github.com>
6 years ago
a43e892fb5
Use 8-bit i2c address on LPC platform
...
Fix #9799 — hopefully not a unicorn
6 years ago
631d867dc9
HAL cleanups
6 years ago
89bbc30a09
Fix init of power supply pin
...
Fix #13184
6 years ago
44c22e3935
Provide a default MAX6675_SS_PIN for ReARM
...
See #8010
6 years ago
3c9a7926c2
Fix compile error with JUNCTION_DEVIATION
...
See #13000
6 years ago
758c6c9464
Very minor SPI speedup
6 years ago
422dd6666e
Fix Due EEPROM write bug
...
See #13065
6 years ago
03e109c4a3
FLASH_EEPROM => FLASH_EEPROM_EMULATION
6 years ago
50917ccda6
Tweak some u8g interface code
6 years ago
ba39186364
TMC_DEBUG optimization and improvements ( #13135 )
6 years ago
1424b368cf
Tweak M122 comment in configs
6 years ago
3a1b6fe8c1
Coding standards
6 years ago
19af90face
Fix a host action compile error ( #13208 )
6 years ago
992cdc8d14
Fix host action / G-code ordering in event_probe_failure ( #13207 )
...
Observing from the console, it makes the most sense to do `//action:probe_retry` before executing commands.
6 years ago
33a6d52965
Fix a RAPTOR2 pin conflict ( #13205 )
6 years ago
52665f54ad
Fix bad Purge More logic ( #13193 )
6 years ago
18458ec42b
Error in Smoothieboard for unsupported display
6 years ago
d4ed9b3ef1
Babystep also requires homing ( #13191 )
6 years ago
ca7b2f574f
Fix condition on tool change filament swap menu ( #13190 )
6 years ago
208ab8b366
Fix compilation with one service interval ( #13185 )
6 years ago
567d03a269
Update Slovak language ( #13187 )
6 years ago
27203c62b8
Enable M240, set photo pins for 3DFabXYZ i3 ( #13174 )
6 years ago
3025ddf179
Support for Creality CR-10 5S ( #13173 )
6 years ago
e00aad84af
Add M240 parameters D I J R S
6 years ago
31c240a8db
Enhancements to G425 ( #13159 )
...
- Turn off bed leveling prior to calibrating.
- This prevents lateral probes from having a Z component that
triggers the Z endstop and causes the motion to be aborted.
- Got rid of static const float arrays "dimension" and "true_center"
- Frees up 24 bytes of SRAM
- Changed incorrect use of "bool" for float in backlash macros.
- Replaced arguments with 0.0f and 1.0f for clarity.
- Now only disables soft endstops (since calibration cube is outside of bed)
- Not necessary to disable global endstops
6 years ago
84fc400aba
Update BIQU SKR V1.1 pins, add TMC2130 settings ( #13166 )
...
* Remove untested displays add TMC2130 configs.
* Remove references to the ReARM, delete untested displays. Add TMC2130 settings. Cleanup spacing, etc.
6 years ago
ab2816c870
Patch for M240
6 years ago
d2bdb71c13
Add PHOTO_GCODE option, photo trigger physical move ( #13168 )
6 years ago
be9a409980
Fix M125 XY parameters, export get_homing_bump_feedrate
6 years ago
ce40c2e87c
Use do_blocking_move_to(ref, fr)
6 years ago
bdc2f10b90
Update Italian language, fix unused var warning ( #13164 )
6 years ago
9f0e1834ec
Followup to #13039 ( #13163 )
...
- Fix compile error when accessing `process_subcommands_now_P`.
- Use `const` var eliminating double-negative (to make code more understandable).
6 years ago
1ace97e946
[2.0.x] Update German language ( #13150 )
6 years ago
7cf9b93f26
Add HAS_FILAMENT_SENSOR ahead of 12962
6 years ago
2c8d12d3ec
Update Italian language ( #13148 )
6 years ago
c2b90c44e4
Prettify some code comments
6 years ago
a0dadc8c62
Smaller I2CPositionEncoder strings
6 years ago
18996d2595
Fix some spelling
6 years ago
e56c13670d
Service interval watchdog ( #13105 )
6 years ago
7f1b69b0c8
Add HOST_PROMPT_SUPPORT ( #13039 )
6 years ago
0feeef2604
Update copyright in headers
6 years ago
894f5c24a8
Fix trailing whitespace
6 years ago
bace52afd7
Fixed compilation with MMU2_MENUS disabled ( #13140 )
6 years ago
584f9cd449
Update German language ( #13137 )
6 years ago
d9a3fea022
Comments in HAL_spi_STM32F1.cpp
6 years ago
773fa5c40f
Fix define used when PID is off ( #13119 )
...
Replaced `PID_MAX` with `BANG_MAX` since it should be the correct define to be used when PID is not enabled.
6 years ago
f7efe6f6c5
[2.0.x] Fix TEMP_STAT_LED startup init ( #13120 )
6 years ago
2bd6ce4b62
Update German language ( #13125 )
6 years ago
27115ff7eb
Update Italian language ( #13123 )
...
Incomplete.
6 years ago
08a8bd10ca
Updated Slovak translation ( #13122 )
6 years ago
3e2a4c3b26
Show mixer and temperature menus while printing
6 years ago
8d271f20fe
C10mini E steps of 95
...
See https://www.patreon.com/posts/creality-cr10-24602624
6 years ago
9737608f0a
Enable gradient when alias is cleared
6 years ago
5cd0fa3ce1
Basic GPIO expander using the ESP32 I2S peripheral ( #12959 )
6 years ago
3983cacbcf
No extern needed for func decl
6 years ago
Vasily Evseenko