microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

Merge SD_DETECT_PIN (PR#2569)

Browse Source
2.0.x
Richard Wackerbarth 10 years ago
parent 496fc28dc3 5418faa1f9
commit eb65c57496
62 changed files with 201 additions and 185 deletions
Show Stats Download Patch File Download Diff File

2
Marlin/Conditionals.h
Unescape Escape View File

@ -321,7 +321,7 @@
#endif
#if ENABLED(ULTIPANEL) && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#undef SDCARDDETECTINVERTED
#undef SD_DETECT_INVERTED
#endif
// Power Signal Control Definitions

2
Marlin/Configuration.h
Unescape Escape View File

@ -674,7 +674,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

13
Marlin/Configuration_adv.h
Unescape Escape View File

@ -291,13 +291,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#ifndef ELB_FULL_GRAPHIC_CONTROLLER
#define SDCARDDETECTINVERTED
#endif
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

8
Marlin/SanityCheck.h
Unescape Escape View File

@ -366,4 +366,12 @@
#error BEEPER has been replaced with BEEPER_PIN. Please update your pins definitions.
#endif
#ifdef SDCARDDETECT
#error SDCARDDETECT is now SD_DETECT_PIN. Please update your pins definitions.
#endif
#ifdef SDCARDDETECTINVERTED
#error SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration.
#endif
#endif //SANITYCHECK_H

8
Marlin/cardreader.h
Unescape Escape View File

@ -81,11 +81,11 @@ extern CardReader card;
#define IS_SD_PRINTING (card.sdprinting)
#if PIN_EXISTS(SDCARDDETECT)
#if ENABLED(SDCARDDETECTINVERTED)
#define IS_SD_INSERTED (READ(SDCARDDETECT_PIN) != 0)
#if PIN_EXISTS(SD_DETECT)
#if ENABLED(SD_DETECT_INVERTED)
#define IS_SD_INSERTED (READ(SD_DETECT_PIN) != 0)
#else
#define IS_SD_INSERTED (READ(SDCARDDETECT_PIN) == 0)
#define IS_SD_INSERTED (READ(SD_DETECT_PIN) == 0)
#endif
#else
//No card detect line? Assume the card is inserted.

2
Marlin/configurator/config/Configuration.h
Unescape Escape View File

@ -674,7 +674,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

13
Marlin/configurator/config/Configuration_adv.h
Unescape Escape View File

@ -291,13 +291,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#ifndef ELB_FULL_GRAPHIC_CONTROLLER
#define SDCARDDETECTINVERTED
#endif
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/Felix/Configuration.h
Unescape Escape View File

@ -652,7 +652,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

2
Marlin/example_configurations/Felix/Configuration_DUAL.h
Unescape Escape View File

@ -610,7 +610,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/Felix/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/Hephestos/Configuration.h
Unescape Escape View File

@ -661,7 +661,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/Hephestos/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/K8200/Configuration.h
Unescape Escape View File

@ -657,7 +657,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/K8200/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
Unescape Escape View File

@ -669,7 +669,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

2
Marlin/example_configurations/RigidBot/Configuration.h
Unescape Escape View File

@ -649,7 +649,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

4
Marlin/example_configurations/RigidBot/Configuration_adv.h
Unescape Escape View File

@ -292,11 +292,11 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// You can get round this by connecting a push button or single throw switch to the pin defined as SD_DETECT_PIN
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#ifndef ELB_FULL_GRAPHIC_CONTROLLER
#define SDCARDDETECTINVERTED
#define SD_DETECT_INVERTED
#endif
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?

2
Marlin/example_configurations/SCARA/Configuration.h
Unescape Escape View File

@ -677,7 +677,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/SCARA/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/WITBOX/Configuration.h
Unescape Escape View File

@ -661,7 +661,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/WITBOX/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/adafruit/ST7565/Configuration.h
Unescape Escape View File

@ -669,7 +669,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

2
Marlin/example_configurations/delta/biv2.5/Configuration.h
Unescape Escape View File

@ -789,7 +789,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
Unescape Escape View File

@ -300,11 +300,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/delta/generic/Configuration.h
Unescape Escape View File

@ -789,7 +789,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/delta/generic/Configuration_adv.h
Unescape Escape View File

@ -300,11 +300,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/delta/kossel_mini/Configuration.h
Unescape Escape View File

@ -793,7 +793,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/delta/kossel_pro/Configuration.h
Unescape Escape View File

@ -788,7 +788,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

13
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
Unescape Escape View File

@ -340,11 +340,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
@ -452,7 +453,7 @@
const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
#if ENABLED(ULTIPANEL)
#undef SDCARDDETECTINVERTED
#undef SD_DETECT_INVERTED
#endif
// Power Signal Control Definitions

2
Marlin/example_configurations/makibox/Configuration.h
Unescape Escape View File

@ -672,7 +672,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

4
Marlin/example_configurations/makibox/Configuration_adv.h
Unescape Escape View File

@ -300,10 +300,10 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// You can get round this by connecting a push button or single throw switch to the pin defined as SD_DETECT_PIN
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/example_configurations/tvrrug/Round2/Configuration.h
Unescape Escape View File

@ -663,7 +663,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
//
// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
//#define ELB_FULL_GRAPHIC_CONTROLLER
//#define SDCARDDETECTINVERTED
//#define SD_DETECT_INVERTED
// The RepRapDiscount Smart Controller (white PCB)
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller

11
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
Unescape Escape View File

@ -299,11 +299,12 @@
#if ENABLED(SDSUPPORT)
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
#define SDCARDDETECTINVERTED
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
// around this by connecting a push button or single throw switch to the pin defined
// as SD_DETECT_PIN in your board's pins definitions.
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
#define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.

2
Marlin/pins_AZTEEG_X3.h
Unescape Escape View File

@ -21,7 +21,7 @@
#define BTN_ENC 12 //the click switch
#define SDSS 53
#define SDCARDDETECT -1 // Pin 49 if using display sd interface
#define SD_DETECT -1 // Pin 49 if using display sd interface
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 64

2
Marlin/pins_AZTEEG_X3_PRO.h
Unescape Escape View File

@ -109,7 +109,7 @@
#define BTN_ENC 39 //the click switch
#define SDSS 53
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#define KILL_PIN 31
#endif

2
Marlin/pins_BRAINWAVE_PRO.h
Unescape Escape View File

@ -54,7 +54,7 @@
#define PS_ON_PIN -1
#define KILL_PIN -1
#define ALARM_PIN -1
#define SDCARDDETECT_PIN 12
#define SD_DETECT_PIN 12
#if DISABLED(SDSUPPORT)
// these pins are defined in the SD library if building with SD support

2
Marlin/pins_CHEAPTRONIC.h
Unescape Escape View File

@ -86,4 +86,4 @@
#define BLEN_A 0
// Cheaptronic v1.0 doesn't use this
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1

2
Marlin/pins_ELEFU_3.h
Unescape Escape View File

@ -64,7 +64,7 @@
#if ENABLED(RA_CONTROL_PANEL)
#define SDSS 53
#define SDCARDDETECT_PIN 28
#define SD_DETECT_PIN 28
#define BTN_EN1 14
#define BTN_EN2 39

2
Marlin/pins_FELIX2.h
Unescape Escape View File

@ -19,6 +19,6 @@
#define BLEN_C 2
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN 6
#define SD_DETECT_PIN 6
#endif // NEWPANEL && ULTRA_LCD

20
Marlin/pins_GEN7_CUSTOM.h
Unescape Escape View File

@ -13,34 +13,34 @@
#define X_STEP_PIN 21 // different from standard GEN7
#define X_DIR_PIN 20 // different from standard GEN7
#define X_ENABLE_PIN 24
#define X_STOP_PIN 0
#define X_STOP_PIN 0
//y axis pins
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_STOP_PIN 1
#define Y_STOP_PIN 1
//z axis pins
#define Z_STEP_PIN 26
#define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24
#define Z_STOP_PIN 2
#define Z_STOP_PIN 2
//extruder pins
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24
#define TEMP_0_PIN 2
#define TEMP_0_PIN 2
#define TEMP_1_PIN -1
#define TEMP_2_PIN -1
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
#define HEATER_0_PIN 4
#define HEATER_0_PIN 4
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN 3 // (bed)
#define HEATER_BED_PIN 3 // (bed)
#define SDPOWER -1
#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
@ -56,9 +56,9 @@
//#define TX_ENABLE_PIN 12
//#define RX_ENABLE_PIN 13
#define BEEPER_PIN -1
#define SDCARDDETECT_PIN -1
#define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work
#define BEEPER_PIN -1
#define SD_DETECT_PIN -1
#define SUICIDE_PIN -1 //has to be defined; otherwise Power_off doesn't work
#define KILL_PIN -1
//Pins for 4bit LCD Support

2
Marlin/pins_LEAPFROG.h
Unescape Escape View File

@ -42,7 +42,7 @@
#define SDPOWER -1
#define SDSS 11
#define SDCARDDETECT_PIN -1 // 10 optional also used as mode pin
#define SD_DETECT_PIN -1 // 10 optional also used as mode pin
#define LED_PIN 13
#define FAN_PIN 7
#define PS_ON_PIN -1

2
Marlin/pins_MEGACONTROLLER.h
Unescape Escape View File

@ -107,6 +107,6 @@
#define BTN_EN2 11
#define BTN_ENC 10 //the click switch
//not connected to a pin
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#endif //Minipanel

2
Marlin/pins_MEGATRONICS.h
Unescape Escape View File

@ -78,6 +78,6 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN -1 // RAMPS doesn't use this
#define SD_DETECT_PIN -1 // RAMPS doesn't use this
#endif // ULTRA_LCD && NEWPANEL

2
Marlin/pins_MEGATRONICS_2.h
Unescape Escape View File

@ -94,4 +94,4 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN -1 // Megatronics doesn't use this
#define SD_DETECT_PIN -1 // Megatronics doesn't use this

2
Marlin/pins_MEGATRONICS_3.h
Unescape Escape View File

@ -99,4 +99,4 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN -1 // Megatronics doesn't use this
#define SD_DETECT_PIN -1 // Megatronics doesn't use this

2
Marlin/pins_MINIRAMBO.h
Unescape Escape View File

@ -107,7 +107,7 @@
#define BTN_EN2 72
#define BTN_ENC 9 // the click
#define SDCARDDETECT_PIN 15
#define SD_DETECT_PIN 15
#endif //NEWPANEL
#endif //ULTRA_LCD

2
Marlin/pins_MINITRONICS.h
Unescape Escape View File

@ -78,4 +78,4 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN -1 // Minitronics doesn't use this
#define SD_DETECT_PIN -1 // Minitronics doesn't use this

2
Marlin/pins_OMCA.h
Unescape Escape View File

@ -70,7 +70,7 @@
#define SDPOWER -1
#define SDSS 11
#define SDCARDDETECT_PIN -1 // 10 optional also used as mode pin
#define SD_DETECT_PIN -1 // 10 optional also used as mode pin
#define LED_PIN -1
#define FAN_PIN 14 // PWM on MIDDLE connector
#define PS_ON_PIN -1

30
Marlin/pins_OMCA_A.h
Unescape Escape View File

@ -35,39 +35,39 @@
#define X_STEP_PIN 21
#define X_DIR_PIN 20
#define X_ENABLE_PIN 24
#define X_STOP_PIN 0
#define X_STOP_PIN 0
#define Y_STEP_PIN 23
#define Y_DIR_PIN 22
#define Y_ENABLE_PIN 24
#define Y_STOP_PIN 1
#define Y_STOP_PIN 1
#define Z_STEP_PIN 26
#define Z_DIR_PIN 25
#define Z_ENABLE_PIN 24
#define Z_STOP_PIN 2
#define Z_STOP_PIN 2
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24
#define E0_STEP_PIN 28
#define E0_DIR_PIN 27
#define E0_ENABLE_PIN 24
#define E1_STEP_PIN -1 // 19
#define E1_DIR_PIN -1 // 18
#define E1_ENABLE_PIN 24
#define E1_STEP_PIN -1 // 19
#define E1_DIR_PIN -1 // 18
#define E1_ENABLE_PIN 24
#define E2_STEP_PIN -1 // 17
#define E2_DIR_PIN -1 // 16
#define E2_ENABLE_PIN 24
#define E2_STEP_PIN -1 // 17
#define E2_DIR_PIN -1 // 16
#define E2_ENABLE_PIN 24
#define SDPOWER -1
#define SDSS 11
#define SDCARDDETECT_PIN -1 // 10 optional also used as mode pin
#define SD_DETECT_PIN -1 // 10 optional also used as mode pin
#define LED_PIN -1
#define FAN_PIN 3
#define FAN_PIN 3
#define PS_ON_PIN -1
#define KILL_PIN -1
#define HEATER_0_PIN 4
#define HEATER_0_PIN 4
#define HEATER_1_PIN -1 // 12
#define HEATER_2_PIN -1 // 13
#define TEMP_0_PIN 0 //D27 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!

4
Marlin/pins_PRINTRBOARD.h
Unescape Escape View File

@ -88,7 +88,7 @@
#define SDSS 40 //use SD card on Panelolu2 (Teensyduino pin mapping)
#endif // LCD_I2C_PANELOLU2
//not connected to a pin
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
@ -104,7 +104,7 @@
#define BTN_ENC 47 //the click switch
#define SDSS 45
#define SDCARDDETECT_PIN -1 // FastIO (Manual says 72 I'm not certain cause I can't test)
#define SD_DETECT_PIN -1 // FastIO (Manual says 72 I'm not certain cause I can't test)
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 12 //Non-FastIO

4
Marlin/pins_RAMBO.h
Unescape Escape View File

@ -133,7 +133,7 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN 81 // Ramps doesn't use this
#define SD_DETECT_PIN 81 // Ramps doesn't use this
#else //!NEWPANEL - old style panel with shift register
@ -180,7 +180,7 @@
#define BTN_EN2 84
#define BTN_ENC 83 //the click switch
#define SDCARDDETECT_PIN -1 // Pin 72 if using easy adapter board
#define SD_DETECT_PIN -1 // Pin 72 if using easy adapter board
#if ENABLED(TEMP_STAT_LEDS)
#define STAT_LED_RED 22

20
Marlin/pins_RAMPS_13.h
Unescape Escape View File

@ -117,10 +117,10 @@
#if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF) || MB(RAMPS_13_SF)
#define HEATER_BED_PIN -1 // NO BED
#else
#define HEATER_BED_PIN 8 // BED
#define HEATER_BED_PIN 8 // BED
#endif
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#define TEMP_BED_PIN 14 // ANALOG NUMBERING
#if HAS_SERVOS
#define SERVO0_PIN 11
@ -136,7 +136,7 @@
#endif
#if ENABLED(Z_PROBE_SLED)
#define SLED_PIN -1
#define SLED_PIN -1
#endif
#if ENABLED(ULTRA_LCD)
@ -165,25 +165,25 @@
#define BTN_EN2 33
#define BTN_ENC 35
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#elif ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 47 // reverse if the encoder turns the wrong way.
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI)
#define BTN_EN1 22 // reverse if the encoder turns the wrong way.
#define BTN_EN2 7
#define BTN_ENC -1
#define LCD_SDSS 53
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define BTN_EN1 35 // reverse if the encoder turns the wrong way.
#define BTN_EN2 37
#define BTN_ENC 31
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
@ -210,7 +210,7 @@
#define BTN_EN2 63
#define BTN_ENC 59 //the click switch
//not connected to a pin
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#else
@ -235,9 +235,9 @@
#endif
#if ENABLED(G3D_PANEL)
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#else
#define SDCARDDETECT_PIN -1 // Ramps doesn't use this
#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif
#endif

12
Marlin/pins_RIGIDBOARD.h
Unescape Escape View File

@ -25,8 +25,8 @@
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef SDCARDDETECT_PIN
#define SDCARDDETECT_PIN 22
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 22
// Extra button definitions, substitute for EN1 / EN2
#define BTN_UP 37 // BTN_EN1
@ -43,16 +43,16 @@
#undef BTN_ENC
#define BTN_ENC 31
#undef SDCARDDETECT_PIN
#define SDCARDDETECT_PIN 22
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 22
#elif defined(REPRAP_DISCOUNT_SMART_CONTROLLER)
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef SDCARDDETECT_PIN
#define SDCARDDETECT_PIN 22
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 22
#undef KILL_PIN
#define KILL_PIN 32

36
Marlin/pins_RUMBA.h
Unescape Escape View File

@ -42,41 +42,41 @@
#define LED_PIN 13
#define FAN_PIN 7
#define FAN1_PIN 8
#define FAN_PIN 7
#define FAN1_PIN 8
#define PS_ON_PIN 45
#define KILL_PIN 46
#if (TEMP_SENSOR_0==0)
#define TEMP_0_PIN -1
#define HEATER_0_PIN -1
#define TEMP_0_PIN -1
#define HEATER_0_PIN -1
#else
#define HEATER_0_PIN 2 // EXTRUDER 1
#define HEATER_0_PIN 2 // EXTRUDER 1
#if (TEMP_SENSOR_0==-1)
#define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
#define TEMP_0_PIN 6 // ANALOG NUMBERING - connector *K1* on RUMBA thermocouple ADD ON is used
#else
#define TEMP_0_PIN 15 // ANALOG NUMBERING - default connector for thermistor *T0* on rumba board is used
#endif
#endif
#if (TEMP_SENSOR_1==0)
#define TEMP_1_PIN -1
#define HEATER_1_PIN -1
#define TEMP_1_PIN -1
#define HEATER_1_PIN -1
#else
#define HEATER_1_PIN 3 // EXTRUDER 2
#define HEATER_1_PIN 3 // EXTRUDER 2
#if (TEMP_SENSOR_1==-1)
#define TEMP_1_PIN 5 // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
#define TEMP_1_PIN 5 // ANALOG NUMBERING - connector *K2* on RUMBA thermocouple ADD ON is used
#else
#define TEMP_1_PIN 14 // ANALOG NUMBERING - default connector for thermistor *T1* on rumba board is used
#endif
#endif
#if (TEMP_SENSOR_2==0)
#define TEMP_2_PIN -1
#define HEATER_2_PIN -1
#define TEMP_2_PIN -1
#define HEATER_2_PIN -1
#else
#define HEATER_2_PIN 6 // EXTRUDER 3
#define HEATER_2_PIN 6 // EXTRUDER 3
#if (TEMP_SENSOR_2==-1)
#define TEMP_2_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple
#else
@ -88,20 +88,20 @@
//optional FAN1 can be used as 4th heater output: #define HEATER_3_PIN 8 // EXTRUDER 4
#if (TEMP_SENSOR_BED==0)
#define TEMP_BED_PIN -1
#define HEATER_BED_PIN -1
#define TEMP_BED_PIN -1
#define HEATER_BED_PIN -1
#else
#define HEATER_BED_PIN 9 // BED
#define HEATER_BED_PIN 9 // BED
#if (TEMP_SENSOR_BED==-1)
#define TEMP_BED_PIN 7 // ANALOG NUMBERING - connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple
#else
#define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
#define TEMP_BED_PIN 11 // ANALOG NUMBERING - default connector for thermistor *THB* on rumba board is used
#endif
#endif
#define SDPOWER -1
#define SDSS 53
#define SDCARDDETECT_PIN 49
#define SD_DETECT_PIN 49
#define BEEPER_PIN 44
#define LCD_PINS_RS 19
#define LCD_PINS_ENABLE 42

4
Marlin/pins_SANGUINOLOLU_11.h
Unescape Escape View File

@ -156,7 +156,7 @@
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
#endif //Panelolu2
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#elif ENABLED(MAKRPANEL)
@ -178,7 +178,7 @@
#define BTN_EN2 10
#define BTN_ENC 16
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#endif // MAKRPANEL

2
Marlin/pins_SAV_MKI.h
Unescape Escape View File

@ -83,7 +83,7 @@
#define LED_PIN -1
#define PS_ON_PIN -1
#define ALARM_PIN -1
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#define BEEPER_PIN -1
#define LCD_PINS_RS -1

2
Marlin/pins_TEENSY2.h
Unescape Escape View File

@ -86,7 +86,7 @@
#define TEMP_2_PIN -1
#define SDPOWER -1
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#define SDSS 20 // 8
#define LED_PIN 6
#define PS_ON_PIN 27

2
Marlin/pins_TEENSYLU.h
Unescape Escape View File

@ -78,7 +78,7 @@
#define SDSS 40 //use SD card on Panelolu2 (Teensyduino pin mapping)
#endif // LCD_I2C_PANELOLU2
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#endif // ULTRA_LCD && NEWPANEL

2
Marlin/pins_ULTIMAIN_2.h
Unescape Escape View File

@ -76,4 +76,4 @@
#define BLEN_B 1
#define BLEN_A 0
#define SDCARDDETECT_PIN 39
#define SD_DETECT_PIN 39

4
Marlin/pins_ULTIMAKER.h
Unescape Escape View File

@ -73,7 +73,7 @@
#define BTN_EN2 42
#define BTN_ENC 19
#define SDCARDDETECT_PIN 38
#define SD_DETECT_PIN 38
#else //!NEWPANEL - Old style panel with shift register
@ -90,7 +90,7 @@
#define LCD_PINS_D6 20
#define LCD_PINS_D7 19
#define SDCARDDETECT_PIN -1
#define SD_DETECT_PIN -1
#endif // !NEWPANEL

18
Marlin/ultralcd.cpp
Unescape Escape View File

@ -221,7 +221,7 @@ static void lcd_status_screen();
millis_t next_button_update_ms;
uint8_t lastEncoderBits;
uint32_t encoderPosition;
#if PIN_EXISTS(SDCARDDETECT)
#if PIN_EXISTS(SD_DETECT)
bool lcd_oldcardstatus;
#endif
@ -411,14 +411,14 @@ static void lcd_main_menu() {
}
else {
MENU_ITEM(submenu, MSG_CARD_MENU, lcd_sdcard_menu);
#if !PIN_EXISTS(SDCARDDETECT)
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(gcode, MSG_CNG_SDCARD, PSTR("M21")); // SD-card changed by user
#endif
}
}
else {
MENU_ITEM(submenu, MSG_NO_CARD, lcd_sdcard_menu);
#if !PIN_EXISTS(SDCARDDETECT)
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(gcode, MSG_INIT_SDCARD, PSTR("M21")); // Manually initialize the SD-card via user interface
#endif
}
@ -1156,7 +1156,7 @@ static void lcd_control_volumetric_menu() {
}
#endif // FWRETRACT
#if !PIN_EXISTS(SDCARDDETECT)
#if !PIN_EXISTS(SD_DETECT)
static void lcd_sd_refresh() {
card.initsd();
currentMenuViewOffset = 0;
@ -1180,7 +1180,7 @@ void lcd_sdcard_menu() {
MENU_ITEM(back, MSG_MAIN, lcd_main_menu);
card.getWorkDirName();
if (card.filename[0] == '/') {
#if !PIN_EXISTS(SDCARDDETECT)
#if !PIN_EXISTS(SD_DETECT)
MENU_ITEM(function, LCD_STR_REFRESH MSG_REFRESH, lcd_sd_refresh);
#endif
}
@ -1407,9 +1407,9 @@ void lcd_init() {
#endif // SR_LCD_2W_NL
#endif//!NEWPANEL
#if ENABLED(SDSUPPORT) && PIN_EXISTS(SDCARDDETECT)
pinMode(SDCARDDETECT_PIN, INPUT);
WRITE(SDCARDDETECT_PIN, HIGH);
#if ENABLED(SDSUPPORT) && PIN_EXISTS(SD_DETECT)
pinMode(SD_DETECT_PIN, INPUT);
WRITE(SD_DETECT_PIN, HIGH);
lcd_oldcardstatus = IS_SD_INSERTED;
#endif
@ -1466,7 +1466,7 @@ void lcd_update() {
lcd_buttons_update();
#if PIN_EXISTS(SDCARDDETECT)
#if PIN_EXISTS(SD_DETECT)
if (IS_SD_INSERTED != lcd_oldcardstatus && lcd_detected()) {
lcdDrawUpdate = 2;
lcd_oldcardstatus = IS_SD_INSERTED;

Write Preview
Loading…
Cancel
Save