scube/Marlin/src/pins/pins_RAMPS_RE_ARM.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * Re-ARM with RAMPS v1.4 pin assignments
 *
 * Applies to the following boards:
 *
 *  RAMPS_14_EFB (Hotend, Fan, Bed)
 *  RAMPS_14_EEB (Hotend0, Hotend1, Bed)
 *  RAMPS_14_EFF (Hotend, Fan0, Fan1)
 *  RAMPS_14_EEF (Hotend0, Hotend1, Fan)
 *  RAMPS_14_SF  (Spindle, Controller Fan)
 *
 */

#ifndef TARGET_LPC1768
  #error "Oops!  Make sure you have LPC1768 selected."
#endif

#ifndef BOARD_NAME
  #define BOARD_NAME "Re-ARM RAMPS 1.4"
#endif

#define LARGE_FLASH true

//
// Servos
//
#define SERVO0_PIN         P1_20
#define SERVO1_PIN         P1_21  // also on J5-1
#define SERVO2_PIN         P1_19
#define SERVO3_PIN         P1_18  // 5V output - PWM capable

//
// Limit Switches
//
#define X_MIN_PIN          P1_24  //10k pullup to 3.3V, 1K series
#define X_MAX_PIN          P1_25  //10k pullup to 3.3V, 1K series
#define Y_MIN_PIN          P1_26  //10k pullup to 3.3V, 1K series
#define Y_MAX_PIN          P1_27  //10k pullup to 3.3V, 1K series
#define Z_MIN_PIN          P1_29  //10k pullup to 3.3V, 1K series
#define Z_MAX_PIN          P1_28  //10k pullup to 3.3V, 1K series

//
// Steppers
//
#define X_STEP_PIN         P2_1
#define X_DIR_PIN          P0_11
#define X_ENABLE_PIN       P0_10

#define Y_STEP_PIN         P2_2
#define Y_DIR_PIN          P0_20
#define Y_ENABLE_PIN       P0_19

#define Z_STEP_PIN         P2_3
#define Z_DIR_PIN          P0_22
#define Z_ENABLE_PIN       P0_21

#define E0_STEP_PIN        P2_0
#define E0_DIR_PIN         P0_5
#define E0_ENABLE_PIN      P0_4

#define E1_STEP_PIN        P2_8
#define E1_DIR_PIN         P2_13
#define E1_ENABLE_PIN      P4_29

#define E2_STEP_PIN        P2_8
#define E2_DIR_PIN         P2_13
#define E2_ENABLE_PIN      P4_29

//
// Temperature Sensors
//  3.3V max when defined as an analog input
//
#define TEMP_0_PIN         0  //A0 (T0) - D67 - TEMP_0_PIN
#define TEMP_BED_PIN       1  //A1 (T1) - D68 - TEMP_BED_PIN
#define TEMP_1_PIN         2  //A2 (T2) - D69 - TEMP_1_PIN
#define TEMP_2_PIN         3  //A3 - D63 - J5-3 & AUX-2
#define TEMP_3_PIN         4  //A4 - D37 - BUZZER_PIN
//#define TEMP_4_PIN         5  //A5 - D49 - SD_DETECT_PIN
//#define ??               6  //A6 - D0  - RXD0 - J4-4 & AUX-1
#define FILWIDTH_PIN       7  //A7 - D1  - TXD0 - J4-5 & AUX-1


//
// Augmentation for auto-assigning RAMPS plugs
//
#if DISABLED(IS_RAMPS_EEB) && DISABLED(IS_RAMPS_EEF) && DISABLED(IS_RAMPS_EFB) && DISABLED(IS_RAMPS_EFF) && DISABLED(IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
  #if HOTENDS > 1
    #if TEMP_SENSOR_BED
      #define IS_RAMPS_EEB
    #else
      #define IS_RAMPS_EEF
    #endif
  #elif TEMP_SENSOR_BED
    #define IS_RAMPS_EFB
  #else
    #define IS_RAMPS_EFF
  #endif
#endif

//
// Heaters / Fans
//
#ifndef MOSFET_D_PIN
  #define MOSFET_D_PIN   -1
#endif
#ifndef RAMPS_D8_PIN
  #define RAMPS_D8_PIN   P2_7
#endif
#ifndef RAMPS_D9_PIN
  #define RAMPS_D9_PIN   P2_4
#endif
#ifndef RAMPS_D10_PIN
  #define RAMPS_D10_PIN  P2_5
#endif

#define HEATER_0_PIN     RAMPS_D10_PIN

#if ENABLED(IS_RAMPS_EFB)                      // Hotend, Fan, Bed
  #define FAN_PIN        RAMPS_D9_PIN
  #define HEATER_BED_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EEF)                    // Hotend, Hotend, Fan
  #define HEATER_1_PIN   RAMPS_D9_PIN
  #define FAN_PIN        RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EEB)                    // Hotend, Hotend, Bed
  #define HEATER_1_PIN   RAMPS_D9_PIN
  #define HEATER_BED_PIN RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_EFF)                    // Hotend, Fan, Fan
  #define FAN_PIN        RAMPS_D9_PIN
  #define FAN1_PIN       RAMPS_D8_PIN
#elif ENABLED(IS_RAMPS_SF)                     // Spindle, Fan
  #define FAN_PIN        RAMPS_D8_PIN
#else                                          // Non-specific are "EFB" (i.e., "EFBF" or "EFBE")
  #define FAN_PIN        RAMPS_D9_PIN
  #define HEATER_BED_PIN RAMPS_D8_PIN
  #if HOTENDS == 1
    #define FAN1_PIN     MOSFET_D_PIN
  #else
    #define HEATER_1_PIN MOSFET_D_PIN
  #endif
#endif

#ifndef FAN_PIN
  #define FAN_PIN         P1_18 // IO pin. Buffer needed
#endif

//
// Misc. Functions
//
#define LED_PIN           P4_28

// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector
#define FIL_RUNOUT_PIN    P1_18

#define PS_ON_PIN         P2_12

#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
  #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector
    #define CASE_LIGHT_PIN    P1_18 // MUST BE HARDWARE PWM
  #endif
#endif

//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE)
  #if !defined(NUM_SERVOS) || NUM_SERVOS == 1 // must use servo connector
    #undef  SERVO1
    #undef  SERVO2
    #undef  SERVO3
    #define SPINDLE_LASER_ENABLE_PIN  P1_21  // Pin should have a pullup/pulldown!
    #define SPINDLE_LASER_PWM_PIN     P1_18  // MUST BE HARDWARE PWM
    #define SPINDLE_DIR_PIN           P1_19
  #endif
#endif
//
// Průša i3 MK2 Multiplexer Support
//
#define E_MUX0_PIN         P0_3    // Z_CS_PIN
#define E_MUX1_PIN         P0_2    // E0_CS_PIN
#define E_MUX2_PIN         P0_26   // E1_CS_PIN

/**
 * LCD / Controller
 *
 * All controllers can use J3 and J5 on the Re-ARM board.  Custom cabling will be required.
 */

/**
 * Smart LCD adapter
 *
 * The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
 * REPRAP_DISCOUNT_SMART_CONTROLLER.  It can't be used for controllers that use
 * DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
 * is needed to pick up 5V for the EXP1 connection.
 *
 * SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
 * on the LCD display during accesses of the SD card. The menus/code has been arranged so
 * that the garbage/lines are erased immediately after the SD card accesses are completed.
 */

#if ENABLED(ULTRA_LCD)

  #define BEEPER_PIN          P1_30  // not 5V tolerant

  #define BTN_EN1             P3_26  // J3-2 & AUX-4
  #define BTN_EN2             P3_25  // J3-4 & AUX-4
  #define BTN_ENC             P2_11  // J3-3 & AUX-4

  #define SD_DETECT_PIN       P1_31  // not 5V tolerant   J3-1 & AUX-3
  #define KILL_PIN            P1_22  // J5-4 & AUX-4
  #define LCD_PINS_RS         P0_16  // J3-7 & AUX-4
  #define LCD_SDSS            P0_16  // J3-7 & AUX-4
  #define LCD_BACKLIGHT_PIN   P0_16  // J3-7 & AUX-4 - only used on DOGLCD controllers
  #define LCD_PINS_ENABLE     P0_18  // (MOSI) J3-10 & AUX-3
  #define LCD_PINS_D4         P0_15  // (SCK)  J3-9 & AUX-3

  #define DOGLCD_A0           P2_6   // J3-8 & AUX-2
  #define DOGLCD_CS           P0_26  // J5-3 & AUX-2

  #ifdef ULTIPANEL
    #define LCD_PINS_D5       P1_17  // ENET_MDIO
    #define LCD_PINS_D6       P1_14  // ENET_RX_ER
    #define LCD_PINS_D7       P1_10  // ENET_RXD1
  #endif

  #if ENABLED(NEWPANEL)
    #if ENABLED(REPRAPWORLD_KEYPAD)
      #define SHIFT_OUT         P0_18  // (MOSI) J3-10 & AUX-3
      #define SHIFT_CLK         P0_15  // (SCK)  J3-9 & AUX-3
      #define SHIFT_LD          P1_31  // not 5V tolerant   J3-1 & AUX-3
    #endif
  #else
    //#define SHIFT_CLK           P3_26  // J3-2 & AUX-4
    //#define SHIFT_LD            P3_25  // J3-4 & AUX-4
    //#define SHIFT_OUT           P2_11  // J3-3 & AUX-4
    //#define SHIFT_EN            P1_22  // J5-4 & AUX-4
  #endif

  #if ENABLED(VIKI2) || ENABLED(miniVIKI)
    // #define LCD_SCREEN_ROT_180

    #undef  BEEPER_PIN
    #define BEEPER_PIN          P1_30  // may change if cable changes

    #define BTN_EN1             P3_26  // J3-2 & AUX-4
    #define BTN_EN2             P3_25  // J3-4 & AUX-4
    #define BTN_ENC             P2_11  // J3-3 & AUX-4

    #define SD_DETECT_PIN       P1_31  // not 5V tolerant   J3-1 & AUX-3
    #define KILL_PIN            P1_22  // J5-4 & AUX-4

    #undef  DOGLCD_CS
    #define DOGLCD_CS           P0_16
    #undef  LCD_BACKLIGHT_PIN   //P0_16  // J3-7 & AUX-4 - only used on DOGLCD controllers
    #undef  LCD_PINS_ENABLE     //P0_18  // (MOSI) J3-10 & AUX-3
    #undef  LCD_PINS_D4         //P0_15  // (SCK)  J3-9 & AUX-3

    #undef  LCD_PINS_D5         //P2_6   // J3-8 & AUX-2
    #define DOGLCD_A0           P2_6   // J3-8 & AUX-2
    #undef  LCD_PINS_D6         //P0_26  // J5-3 & AUX-2
    #undef  LCD_PINS_D7         //P1_21  // (SERVO1) J5-1 & SERVO connector
    #define DOGLCD_SCK          SCK_PIN
    #define DOGLCD_MOSI         MOSI_PIN

    #define STAT_LED_BLUE_PIN   P0_26  // may change if cable changes
    #define STAT_LED_RED_PIN    P1_21  // may change if cable changes
  #endif

  //#define MISO_PIN            P0_17  // system defined J3-10 & AUX-3
  //#define MOSI_PIN            P0_18  // system defined J3-10 & AUX-3
  //#define SCK_PIN             P0_15  // system defined J3-9 & AUX-3
  //#define SS_PIN              P1_23  // system defined J3-5 & AUX-3 - sometimes called SDSS

  #if ENABLED(MINIPANEL)
    // GLCD features
    //#define LCD_CONTRAST   190
    // Uncomment screen orientation
    //#define LCD_SCREEN_ROT_90
    //#define LCD_SCREEN_ROT_180
    //#define LCD_SCREEN_ROT_270
  #endif

#endif // ULTRA_LCD

//
// Ethernet pins
//
#ifndef ULTIPANEL
  #define ENET_MDIO   P1_17  // J12-4
  #define ENET_RX_ER  P1_14  // J12-6
  #define ENET_RXD1   P1_10  // J12-8
#endif
#define ENET_MOC      P1_16  // J12-3
#define REF_CLK       P1_15  // J12-5
#define ENET_RXD0     P1_9   // J12-7
#define ENET_CRS      P1_8   // J12-9
#define ENET_TX_EN    P1_4   // J12-10
#define ENET_TXD0     P1_0   // J12-11
#define ENET_TXD1     P1_1   // J12-12

/**
 *  PWMS
 *
 *  There are 6 PWMS.  Each PWM can be assigned to one of two pins.
 *
 *  SERVO2 does NOT have a PWM assigned to it.
 *
 *  PWM1.1   P0_18   SERVO3_PIN       FIL_RUNOUT_PIN   5V output, PWM
 *  PWM1.1   P2_0    E0_STEP_PIN
 *  PWM1.2   P1_20   SERVO0_PIN
 *  PWM1.2   P2_1    X_STEP_PIN
 *  PWM1.3   P1_21   SERVO1_PIN       J5-1
 *  PWM1.3   P2_2    Y_STEP_PIN
 *  PWM1.4   P1_23   SDSS(SSEL0)      J3-5  AUX-3
 *  PWM1.4   P2_3    Z_STEP_PIN
 *  PWM1.5   P1_24   X_MIN_PIN        10K PULLUP TO 3.3v, 1K SERIES
 *  PWM1.5   P2_4    RAMPS_D9_PIN
 *  PWM1.6   P1_26   Y_MIN_PIN        10K PULLUP TO 3.3v, 1K SERIES
 *  PWM1.6   P2_5    RAMPS_D10_PIN
 */

 /**
  * special pins
  *   P1_30 - not 5V tolerant
  *   P1_31 - not 5V tolerant
  *   P0_27 - open collector
  *   P0_28 - open collector
  *
 */