diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp
index 98c065fba..0dab3bb41 100644
--- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp
+++ b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp
@@ -56,108 +56,106 @@
 
 */
 
-
 #ifdef __SAM3X8E__
 
-//  #include <inttypes.h>
-
-//  #include "src/core/macros.h"
-//  #include "Configuration.h"
-#include "../../Marlin.h"
-#include "../../inc/MarlinConfig.h"
-
-  #include <U8glib.h>
-
-  #define SPI_FULL_SPEED 0
-  #define SPI_HALF_SPEED 1
-  #define SPI_QUARTER_SPEED 2
-  #define SPI_EIGHTH_SPEED 3
-  #define SPI_SIXTEENTH_SPEED 4
-  #define SPI_SPEED_5 5
-  #define SPI_SPEED_6 6
-
-  void spiBegin();
-  void spiInit(uint8_t spiRate);
-  void spiSend(uint8_t b);
-  void spiSend(const uint8_t* buf, size_t n);
+#include "../../inc/MarlinConfigPre.h"
 
-  #include <Arduino.h>
-  #include "../../core/macros.h"
-  #include "fastio_Due.h"
+#if ENABLED(DOGLCD)
 
+#include <U8glib.h>
 
-  void u8g_SetPIOutput_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index) {
-     PIO_Configure(g_APinDescription[u8g->pin_list[pin_index]].pPort, PIO_OUTPUT_1,
-       g_APinDescription[u8g->pin_list[pin_index]].ulPin, g_APinDescription[u8g->pin_list[pin_index]].ulPinConfiguration);  // OUTPUT
-  }
-
-  void u8g_SetPILevel_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index, uint8_t level) {
-    volatile Pio* port = g_APinDescription[u8g->pin_list[pin_index]].pPort;
-    uint32_t mask = g_APinDescription[u8g->pin_list[pin_index]].ulPin;
-    if (level) port->PIO_SODR = mask;
-    else port->PIO_CODR = mask;
-  }
+#include "../../Marlin.h"
 
-  uint8_t u8g_com_HAL_DUE_shared_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr)
+#define SPI_FULL_SPEED 0
+#define SPI_HALF_SPEED 1
+#define SPI_QUARTER_SPEED 2
+#define SPI_EIGHTH_SPEED 3
+#define SPI_SIXTEENTH_SPEED 4
+#define SPI_SPEED_5 5
+#define SPI_SPEED_6 6
+
+void spiBegin();
+void spiInit(uint8_t spiRate);
+void spiSend(uint8_t b);
+void spiSend(const uint8_t* buf, size_t n);
+
+#include <Arduino.h>
+#include "fastio_Due.h"
+
+void u8g_SetPIOutput_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index) {
+   PIO_Configure(g_APinDescription[u8g->pin_list[pin_index]].pPort, PIO_OUTPUT_1,
+     g_APinDescription[u8g->pin_list[pin_index]].ulPin, g_APinDescription[u8g->pin_list[pin_index]].ulPinConfiguration);  // OUTPUT
+}
+
+void u8g_SetPILevel_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index, uint8_t level) {
+  volatile Pio* port = g_APinDescription[u8g->pin_list[pin_index]].pPort;
+  uint32_t mask = g_APinDescription[u8g->pin_list[pin_index]].ulPin;
+  if (level) port->PIO_SODR = mask;
+  else port->PIO_CODR = mask;
+}
+
+uint8_t u8g_com_HAL_DUE_shared_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr)
+{
+  switch(msg)
   {
-    switch(msg)
-    {
-      case U8G_COM_MSG_STOP:
-        break;
+    case U8G_COM_MSG_STOP:
+      break;
 
-      case U8G_COM_MSG_INIT:
-        u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_CS, 1);
-        u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_A0, 1);
+    case U8G_COM_MSG_INIT:
+      u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_CS, 1);
+      u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_A0, 1);
 
-        u8g_SetPIOutput_DUE_hw_spi(u8g, U8G_PI_CS);
-        u8g_SetPIOutput_DUE_hw_spi(u8g, U8G_PI_A0);
+      u8g_SetPIOutput_DUE_hw_spi(u8g, U8G_PI_CS);
+      u8g_SetPIOutput_DUE_hw_spi(u8g, U8G_PI_A0);
 
-        u8g_Delay(5);
+      u8g_Delay(5);
 
-        spiBegin();
+      spiBegin();
 
-        #ifndef SPI_SPEED
-          #define SPI_SPEED SPI_FULL_SPEED  // use same SPI speed as SD card
-        #endif
-        spiInit(2);
+      #ifndef SPI_SPEED
+        #define SPI_SPEED SPI_FULL_SPEED  // use same SPI speed as SD card
+      #endif
+      spiInit(2);
 
-        break;
+      break;
 
-      case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
-        u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_A0, arg_val);
-        break;
+    case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
+      u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_A0, arg_val);
+      break;
 
-      case U8G_COM_MSG_CHIP_SELECT:
-        u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_CS, (arg_val ? 0 : 1));
-        break;
+    case U8G_COM_MSG_CHIP_SELECT:
+      u8g_SetPILevel_DUE_hw_spi(u8g, U8G_PI_CS, (arg_val ? 0 : 1));
+      break;
 
-      case U8G_COM_MSG_RESET:
-        break;
+    case U8G_COM_MSG_RESET:
+      break;
 
-      case U8G_COM_MSG_WRITE_BYTE:
+    case U8G_COM_MSG_WRITE_BYTE:
 
-        spiSend((uint8_t)arg_val);
-        break;
+      spiSend((uint8_t)arg_val);
+      break;
 
-      case U8G_COM_MSG_WRITE_SEQ: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            spiSend(*ptr++);
-            arg_val--;
-          }
+    case U8G_COM_MSG_WRITE_SEQ: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          spiSend(*ptr++);
+          arg_val--;
         }
-        break;
-
-      case U8G_COM_MSG_WRITE_SEQ_P: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            spiSend(*ptr++);
-            arg_val--;
-          }
+      }
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ_P: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          spiSend(*ptr++);
+          arg_val--;
         }
-        break;
-    }
-    return 1;
+      }
+      break;
   }
+  return 1;
+}
+
+#endif  // DOGLCD
 
 #endif  //__SAM3X8E__
diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp
index 7f2d1caf9..df33f9db6 100644
--- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp
+++ b/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp
@@ -55,9 +55,12 @@
 
 #ifdef ARDUINO_ARCH_SAM
 
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(DOGLCD)
+
 #include <U8glib.h>
 #include <Arduino.h>
-#include "../../core/macros.h"
 #include "../Delay.h"
 
 void u8g_SetPIOutput_DUE(u8g_t *u8g, uint8_t pin_index) {
@@ -177,4 +180,6 @@ uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va
   return 1;
 }
 
-#endif  //ARDUINO_ARCH_SAM
+#endif // DOGLCD
+
+#endif // ARDUINO_ARCH_SAM
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_hw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_hw_spi.cpp
index 07255aed2..9cd913f74 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_hw_spi.cpp
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_hw_spi.cpp
@@ -55,11 +55,11 @@
 
 #ifdef TARGET_LPC1768
 
-//#include <inttypes.h>
+#include "../../inc/MarlinConfigPre.h"
 
-//#include "src/core/macros.h"
-//#include "Configuration.h"
+#if ENABLED(DOGLCD)
 
+//#include <inttypes.h>
 #include <U8glib.h>
 
 #define SPI_FULL_SPEED 0
@@ -132,4 +132,6 @@ uint8_t u8g_com_HAL_LPC1768_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
   return 1;
 }
 
-#endif  //TARGET_LPC1768
+#endif // DOGLCD
+
+#endif // TARGET_LPC1768
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp
index e86051ee4..9d72cf024 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_hw_i2c.cpp
@@ -77,113 +77,119 @@
 
 #ifdef TARGET_LPC1768
 
-  #include <U8glib.h>
-
-  #define I2C_SLA         (0x3C*2)
-  //#define I2C_CMD_MODE  0x080
-  #define I2C_CMD_MODE    0x000
-  #define I2C_DATA_MODE   0x040
-
-  //#define U8G_I2C_OPT_FAST 16
-
-  uint8_t u8g_com_ssd_I2C_start_sequence(u8g_t *u8g) {
-    /* are we requested to set the a0 state? */
-    if (u8g->pin_list[U8G_PI_SET_A0] == 0) return 1;
-
-    /* setup bus, might be a repeated start */
-    if (u8g_i2c_start(I2C_SLA) == 0)
-      return 0;
-    if (u8g->pin_list[U8G_PI_A0_STATE] == 0 ) {
-      if (u8g_i2c_send_byte(I2C_CMD_MODE) == 0) return 0;
-    }
-    else if (u8g_i2c_send_byte(I2C_DATA_MODE) == 0)
-      return 0;
-
-    u8g->pin_list[U8G_PI_SET_A0] = 0;
-    return 1;
-  }
+#include "../../inc/MarlinConfigPre.h"
 
-  uint8_t u8g_com_HAL_LPC1768_ssd_hw_i2c_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
-    switch(msg) {
-      case U8G_COM_MSG_INIT:
-        //u8g_com_arduino_digital_write(u8g, U8G_PI_SCL, HIGH);
-        //u8g_com_arduino_digital_write(u8g, U8G_PI_SDA, HIGH);
-        //u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: unknown mode */
-
-        u8g_i2c_init(u8g->pin_list[U8G_PI_I2C_OPTION]);
-        u8g_com_ssd_I2C_start_sequence(u8g);
-        break;
-
-      case U8G_COM_MSG_STOP:
-        break;
-
-      case U8G_COM_MSG_RESET:
-        /* Currently disabled, but it could be enable. Previous restrictions have been removed */
-        /* u8g_com_arduino_digital_write(u8g, U8G_PI_RESET, arg_val); */
-        break;
-
-      case U8G_COM_MSG_CHIP_SELECT:
-        u8g->pin_list[U8G_PI_A0_STATE] = 0;
-        u8g->pin_list[U8G_PI_SET_A0] = 1;   /* force a0 to set again, also forces start condition */
-        if (arg_val == 0 ) {
-          /* disable chip, send stop condition */
-          u8g_i2c_stop();
-        }
-        else {
-          /* enable, do nothing: any byte writing will trigger the i2c start */
-        }
-        break;
+#if ENABLED(DOGLCD)
 
-      case U8G_COM_MSG_WRITE_BYTE:
-        //u8g->pin_list[U8G_PI_SET_A0] = 1;
-        //if (u8g_com_arduino_ssd_start_sequence(u8g) == 0)
-        //  return u8g_i2c_stop(), 0;
-        if (u8g_i2c_send_byte(arg_val) == 0)
-          return u8g_i2c_stop(), 0;
-        // u8g_i2c_stop();
-        break;
+#include <U8glib.h>
+
+#define I2C_SLA         (0x3C*2)
+//#define I2C_CMD_MODE  0x080
+#define I2C_CMD_MODE    0x000
+#define I2C_DATA_MODE   0x040
+
+//#define U8G_I2C_OPT_FAST 16
+
+uint8_t u8g_com_ssd_I2C_start_sequence(u8g_t *u8g) {
+  /* are we requested to set the a0 state? */
+  if (u8g->pin_list[U8G_PI_SET_A0] == 0) return 1;
 
-      case U8G_COM_MSG_WRITE_SEQ: {
+  /* setup bus, might be a repeated start */
+  if (u8g_i2c_start(I2C_SLA) == 0)
+    return 0;
+  if (u8g->pin_list[U8G_PI_A0_STATE] == 0 ) {
+    if (u8g_i2c_send_byte(I2C_CMD_MODE) == 0) return 0;
+  }
+  else if (u8g_i2c_send_byte(I2C_DATA_MODE) == 0)
+    return 0;
+
+  u8g->pin_list[U8G_PI_SET_A0] = 0;
+  return 1;
+}
+
+uint8_t u8g_com_HAL_LPC1768_ssd_hw_i2c_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
+  switch(msg) {
+    case U8G_COM_MSG_INIT:
+      //u8g_com_arduino_digital_write(u8g, U8G_PI_SCL, HIGH);
+      //u8g_com_arduino_digital_write(u8g, U8G_PI_SDA, HIGH);
+      //u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: unknown mode */
+
+      u8g_i2c_init(u8g->pin_list[U8G_PI_I2C_OPTION]);
+      u8g_com_ssd_I2C_start_sequence(u8g);
+      break;
+
+    case U8G_COM_MSG_STOP:
+      break;
+
+    case U8G_COM_MSG_RESET:
+      /* Currently disabled, but it could be enable. Previous restrictions have been removed */
+      /* u8g_com_arduino_digital_write(u8g, U8G_PI_RESET, arg_val); */
+      break;
+
+    case U8G_COM_MSG_CHIP_SELECT:
+      u8g->pin_list[U8G_PI_A0_STATE] = 0;
+      u8g->pin_list[U8G_PI_SET_A0] = 1;   /* force a0 to set again, also forces start condition */
+      if (arg_val == 0 ) {
+        /* disable chip, send stop condition */
+        u8g_i2c_stop();
+      }
+      else {
+        /* enable, do nothing: any byte writing will trigger the i2c start */
+      }
+      break;
+
+    case U8G_COM_MSG_WRITE_BYTE:
+      //u8g->pin_list[U8G_PI_SET_A0] = 1;
+      //if (u8g_com_arduino_ssd_start_sequence(u8g) == 0)
+      //  return u8g_i2c_stop(), 0;
+      if (u8g_i2c_send_byte(arg_val) == 0)
+        return u8g_i2c_stop(), 0;
+      // u8g_i2c_stop();
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ: {
+      //u8g->pin_list[U8G_PI_SET_A0] = 1;
+      if (u8g_com_ssd_I2C_start_sequence(u8g) == 0)
+        return u8g_i2c_stop(), 0;
+
+        register uint8_t *ptr = (uint8_t *)arg_ptr;
+        while (arg_val > 0) {
+          if (u8g_i2c_send_byte(*ptr++) == 0)
+            return u8g_i2c_stop(), 0;
+          arg_val--;
+        }
+      }
+      // u8g_i2c_stop();
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ_P: {
         //u8g->pin_list[U8G_PI_SET_A0] = 1;
         if (u8g_com_ssd_I2C_start_sequence(u8g) == 0)
           return u8g_i2c_stop(), 0;
 
-          register uint8_t *ptr = (uint8_t *)arg_ptr;
-          while (arg_val > 0) {
-            if (u8g_i2c_send_byte(*ptr++) == 0)
-              return u8g_i2c_stop(), 0;
-            arg_val--;
-          }
+        register uint8_t *ptr = (uint8_t *)arg_ptr;
+        while (arg_val > 0) {
+          if (u8g_i2c_send_byte(u8g_pgm_read(ptr)) == 0)
+            return 0;
+          ptr++;
+          arg_val--;
         }
-        // u8g_i2c_stop();
-        break;
+      }
+      // u8g_i2c_stop();
+      break;
 
-      case U8G_COM_MSG_WRITE_SEQ_P: {
-          //u8g->pin_list[U8G_PI_SET_A0] = 1;
-          if (u8g_com_ssd_I2C_start_sequence(u8g) == 0)
-            return u8g_i2c_stop(), 0;
-
-          register uint8_t *ptr = (uint8_t *)arg_ptr;
-          while (arg_val > 0) {
-            if (u8g_i2c_send_byte(u8g_pgm_read(ptr)) == 0)
-              return 0;
-            ptr++;
-            arg_val--;
-          }
-        }
-        // u8g_i2c_stop();
-        break;
+    case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
+      u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
+      u8g->pin_list[U8G_PI_SET_A0] = 1;   /* force a0 to set again */
 
-      case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
-        u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
-        u8g->pin_list[U8G_PI_SET_A0] = 1;   /* force a0 to set again */
+      u8g_i2c_start(0); // send slave address and write bit
+      u8g_i2c_send_byte(arg_val ? 0x40 : 0x80);  // Write to ? Graphics DRAM mode : Command mode
+      break;
 
-        u8g_i2c_start(0); // send slave address and write bit
-        u8g_i2c_send_byte(arg_val ? 0x40 : 0x80);  // Write to ? Graphics DRAM mode : Command mode
-        break;
+  } // switch
+  return 1;
+}
 
-    } // switch
-    return 1;
-  }
+#endif // DOGLCD
 
 #endif // TARGET_LPC1768
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_sw_i2c.cpp  under construction b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_sw_i2c.cpp  under construction
index d93ea2a1f..80c8da723 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_sw_i2c.cpp  under construction	
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_ssd_sw_i2c.cpp  under construction	
@@ -61,16 +61,20 @@
 
 #ifdef TARGET_LPC1768
 
-  #include <U8glib.h>
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(DOGLCD)
+
+#include <U8glib.h>
 
 //void pinMode(int16_t pin, uint8_t mode);
 //void digitalWrite(int16_t pin, uint8_t pin_status);
 
 
-  #define I2C_SLA         (0x3C*2)
-  //#define I2C_CMD_MODE  0x080
-  #define I2C_CMD_MODE    0x000
-  #define I2C_DATA_MODE   0x040
+#define I2C_SLA         (0x3C*2)
+//#define I2C_CMD_MODE  0x080
+#define I2C_CMD_MODE    0x000
+#define I2C_DATA_MODE   0x040
 
 //static uint8_t I2C_speed; // 3 - 400KHz, 13 - 100KHz
 //#define SPEED_400KHz 3
@@ -245,4 +249,6 @@ uint8_t u8g_com_HAL_LPC1768_ssd_sw_i2c_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_v
   return 1;
 }
 
-#endif  // TARGET_LPC1768
+#endif // DOGLCD
+
+#endif // TARGET_LPC1768
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp
index a93ca221c..b903cac26 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp
@@ -55,103 +55,100 @@
 
 #ifdef TARGET_LPC1768
 
-  //#include <inttypes.h>
-  //#include "src/core/macros.h"
-  //#include "Configuration.h"
+#include "../../inc/MarlinConfigPre.h"
 
-  #include <U8glib.h>
-  #include "../Delay.h"
+#if ENABLED(DOGLCD)
 
-  #define SPI_FULL_SPEED 0
-  #define SPI_HALF_SPEED 1
-  #define SPI_QUARTER_SPEED 2
-  #define SPI_EIGHTH_SPEED 3
-  #define SPI_SIXTEENTH_SPEED 4
-  #define SPI_SPEED_5 5
-  #define SPI_SPEED_6 6
+//#include <inttypes.h>
+#include <U8glib.h>
+#include "../Delay.h"
 
+#define SPI_FULL_SPEED 0
+#define SPI_HALF_SPEED 1
+#define SPI_QUARTER_SPEED 2
+#define SPI_EIGHTH_SPEED 3
+#define SPI_SIXTEENTH_SPEED 4
+#define SPI_SPEED_5 5
+#define SPI_SPEED_6 6
 
-  void spiBegin();
-  void spiInit(uint8_t spiRate);
-  void spiSend(uint8_t b);
-  void spiSend(const uint8_t* buf, size_t n);
+void spiBegin();
+void spiInit(uint8_t spiRate);
+void spiSend(uint8_t b);
+void spiSend(const uint8_t* buf, size_t n);
 
+static uint8_t rs_last_state = 255;
 
-  static uint8_t rs_last_state = 255;
+static void u8g_com_LPC1768_st7920_write_byte_hw_spi(uint8_t rs, uint8_t val) {
+  uint8_t i;
 
-  static void u8g_com_LPC1768_st7920_write_byte_hw_spi(uint8_t rs, uint8_t val)
-  {
-    uint8_t i;
+  if ( rs != rs_last_state) {  // time to send a command/data byte
+    rs_last_state = rs;
 
-    if ( rs != rs_last_state) {  // time to send a command/data byte
-      rs_last_state = rs;
+    if ( rs == 0 )
+      /* command */
+      spiSend(0x0F8);
+    else
+       /* data */
+      spiSend(0x0FA);
 
-      if ( rs == 0 )
-        /* command */
-        spiSend(0x0F8);
-      else
-         /* data */
-        spiSend(0x0FA);
-
-      DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe
-    }
-
-    spiSend(val & 0x0F0);
-    spiSend(val << 4);
+    DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe
   }
 
-
-  uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr)
-  {
-    switch(msg)
-    {
-      case U8G_COM_MSG_INIT:
-        u8g_SetPILevel(u8g, U8G_PI_CS, 0);
-        u8g_SetPIOutput(u8g, U8G_PI_CS);
-        u8g_Delay(5);
-        spiBegin();
-        spiInit(SPI_EIGHTH_SPEED);  // ST7920 max speed is about 1.1 MHz
-        u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: command mode */
-        break;
-
-      case U8G_COM_MSG_STOP:
-        break;
-
-      case U8G_COM_MSG_RESET:
-        u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
-        break;
-
-      case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
-        u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
-        break;
-
-      case U8G_COM_MSG_CHIP_SELECT:
-        u8g_SetPILevel(u8g, U8G_PI_CS, arg_val);  //note: the st7920 has an active high chip select
-        break;
-
-      case U8G_COM_MSG_WRITE_BYTE:
-        u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], arg_val);
-        break;
-
-      case U8G_COM_MSG_WRITE_SEQ: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
-            arg_val--;
-          }
+  spiSend(val & 0x0F0);
+  spiSend(val << 4);
+}
+
+uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
+  switch(msg) {
+    case U8G_COM_MSG_INIT:
+      u8g_SetPILevel(u8g, U8G_PI_CS, 0);
+      u8g_SetPIOutput(u8g, U8G_PI_CS);
+      u8g_Delay(5);
+      spiBegin();
+      spiInit(SPI_EIGHTH_SPEED);  // ST7920 max speed is about 1.1 MHz
+      u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: command mode */
+      break;
+
+    case U8G_COM_MSG_STOP:
+      break;
+
+    case U8G_COM_MSG_RESET:
+      u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
+      break;
+
+    case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
+      u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
+      break;
+
+    case U8G_COM_MSG_CHIP_SELECT:
+      u8g_SetPILevel(u8g, U8G_PI_CS, arg_val);  //note: the st7920 has an active high chip select
+      break;
+
+    case U8G_COM_MSG_WRITE_BYTE:
+      u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], arg_val);
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
+          arg_val--;
         }
-        break;
-
-        case U8G_COM_MSG_WRITE_SEQ_P: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
-            arg_val--;
-          }
+      }
+      break;
+
+      case U8G_COM_MSG_WRITE_SEQ_P: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          u8g_com_LPC1768_st7920_write_byte_hw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
+          arg_val--;
         }
-        break;
-    }
-    return 1;
+      }
+      break;
   }
+  return 1;
+}
+
+#endif // DOGLCD
 
-#endif  // TARGET_LPC1768
+#endif // TARGET_LPC1768
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
index 4112a1173..aaa37e256 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
@@ -55,97 +55,102 @@
 
 #ifdef TARGET_LPC1768
 
-  #include <U8glib.h>
-  #include "SoftwareSPI.h"
-  #include "../Delay.h"
+#include "../../inc/MarlinConfigPre.h"
 
-  #define SPI_SPEED 3  // About 1 MHz
+#if ENABLED(DOGLCD)
 
-  static pin_t SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL;
-  static uint8_t SPI_speed = 0;
-  static uint8_t rs_last_state = 255;
+#include <U8glib.h>
+#include "SoftwareSPI.h"
+#include "../Delay.h"
 
-  static void u8g_com_LPC1768_st7920_write_byte_sw_spi(uint8_t rs, uint8_t val)
-  {
-    uint8_t i;
+#define SPI_SPEED 3  // About 1 MHz
+
+static pin_t SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL;
+static uint8_t SPI_speed = 0;
+static uint8_t rs_last_state = 255;
 
-    if ( rs != rs_last_state) {  // time to send a command/data byte
-      rs_last_state = rs;
+static void u8g_com_LPC1768_st7920_write_byte_sw_spi(uint8_t rs, uint8_t val) {
+  uint8_t i;
 
-      if ( rs == 0 )
-        /* command */
-        swSpiTransfer(0x0F8, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
-      else
-         /* data */
-         swSpiTransfer(0x0FA, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
+  if (rs != rs_last_state) {  // time to send a command/data byte
+    rs_last_state = rs;
 
-      DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe
-    }
+    if (rs == 0)
+      /* command */
+      swSpiTransfer(0x0F8, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
+    else
+       /* data */
+       swSpiTransfer(0x0FA, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
 
-    swSpiTransfer(val & 0x0F0, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
-    swSpiTransfer(val << 4, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
+    DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe
   }
 
-  uint8_t u8g_com_HAL_LPC1768_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr)
+  swSpiTransfer(val & 0x0F0, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
+  swSpiTransfer(val << 4, SPI_speed, SCK_pin_ST7920_HAL, -1, MOSI_pin_ST7920_HAL_HAL);
+}
+
+uint8_t u8g_com_HAL_LPC1768_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr)
+{
+  switch(msg)
   {
-    switch(msg)
-    {
-      case U8G_COM_MSG_INIT:
-        SCK_pin_ST7920_HAL = u8g->pin_list[U8G_PI_SCK];
-        MOSI_pin_ST7920_HAL_HAL = u8g->pin_list[U8G_PI_MOSI];
-
-        u8g_SetPIOutput(u8g, U8G_PI_CS);
-        u8g_SetPIOutput(u8g, U8G_PI_SCK);
-        u8g_SetPIOutput(u8g, U8G_PI_MOSI);
-        u8g_Delay(5);
-
-        SPI_speed = swSpiInit(SPI_SPEED, SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL);
-
-        u8g_SetPILevel(u8g, U8G_PI_CS, 0);
-        u8g_SetPILevel(u8g, U8G_PI_SCK, 0);
-        u8g_SetPILevel(u8g, U8G_PI_MOSI, 0);
-
-        u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: command mode */
-        break;
-
-      case U8G_COM_MSG_STOP:
-        break;
-
-      case U8G_COM_MSG_RESET:
-         if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_RESET]) u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
-        break;
-
-      case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
-        u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
-        break;
-
-      case U8G_COM_MSG_CHIP_SELECT:
-        if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_CS]) u8g_SetPILevel(u8g, U8G_PI_CS, arg_val);  //note: the st7920 has an active high chip select
-        break;
-
-      case U8G_COM_MSG_WRITE_BYTE:
-        u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], arg_val);
-        break;
-
-      case U8G_COM_MSG_WRITE_SEQ: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
-            arg_val--;
-          }
+    case U8G_COM_MSG_INIT:
+      SCK_pin_ST7920_HAL = u8g->pin_list[U8G_PI_SCK];
+      MOSI_pin_ST7920_HAL_HAL = u8g->pin_list[U8G_PI_MOSI];
+
+      u8g_SetPIOutput(u8g, U8G_PI_CS);
+      u8g_SetPIOutput(u8g, U8G_PI_SCK);
+      u8g_SetPIOutput(u8g, U8G_PI_MOSI);
+      u8g_Delay(5);
+
+      SPI_speed = swSpiInit(SPI_SPEED, SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL);
+
+      u8g_SetPILevel(u8g, U8G_PI_CS, 0);
+      u8g_SetPILevel(u8g, U8G_PI_SCK, 0);
+      u8g_SetPILevel(u8g, U8G_PI_MOSI, 0);
+
+      u8g->pin_list[U8G_PI_A0_STATE] = 0;       /* inital RS state: command mode */
+      break;
+
+    case U8G_COM_MSG_STOP:
+      break;
+
+    case U8G_COM_MSG_RESET:
+       if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_RESET]) u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
+      break;
+
+    case U8G_COM_MSG_ADDRESS:                     /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
+      u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
+      break;
+
+    case U8G_COM_MSG_CHIP_SELECT:
+      if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_CS]) u8g_SetPILevel(u8g, U8G_PI_CS, arg_val);  //note: the st7920 has an active high chip select
+      break;
+
+    case U8G_COM_MSG_WRITE_BYTE:
+      u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], arg_val);
+      break;
+
+    case U8G_COM_MSG_WRITE_SEQ: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
+          arg_val--;
         }
-        break;
-
-        case U8G_COM_MSG_WRITE_SEQ_P: {
-          uint8_t *ptr = (uint8_t*) arg_ptr;
-          while (arg_val > 0) {
-            u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
-            arg_val--;
-          }
+      }
+      break;
+
+      case U8G_COM_MSG_WRITE_SEQ_P: {
+        uint8_t *ptr = (uint8_t*) arg_ptr;
+        while (arg_val > 0) {
+          u8g_com_LPC1768_st7920_write_byte_sw_spi(u8g->pin_list[U8G_PI_A0_STATE], *ptr++);
+          arg_val--;
         }
-        break;
-    }
-    return 1;
+      }
+      break;
   }
+  return 1;
+}
+
+#endif // DOGLCD
 
-#endif  //TARGET_LPC1768
+#endif // TARGET_LPC1768
diff --git a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_sw_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_sw_spi.cpp
index 64a4dd99c..533ebda37 100644
--- a/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_sw_spi.cpp
+++ b/Marlin/src/HAL/HAL_LPC1768/u8g_com_HAL_LPC1768_sw_spi.cpp
@@ -55,6 +55,10 @@
 
 #ifdef TARGET_LPC1768
 
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(DOGLCD)
+
 #include <U8glib.h>
 #include "SoftwareSPI.h"
 
@@ -120,4 +124,6 @@ uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
   return 1;
 }
 
+#endif // DOGLCD
+
 #endif // TARGET_LPC1768
diff --git a/Marlin/src/lcd/dogm/u8g_dev_ssd1306_sh1106_128x64_I2C.cpp b/Marlin/src/lcd/dogm/u8g_dev_ssd1306_sh1106_128x64_I2C.cpp
index e0063e83a..324906829 100644
--- a/Marlin/src/lcd/dogm/u8g_dev_ssd1306_sh1106_128x64_I2C.cpp
+++ b/Marlin/src/lcd/dogm/u8g_dev_ssd1306_sh1106_128x64_I2C.cpp
@@ -65,7 +65,7 @@
  * beginning.
  */
 
-#include "../../inc/MarlinConfig.h"
+#include "../../inc/MarlinConfigPre.h"
 
 #if ENABLED(DOGLCD)
 
diff --git a/Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp b/Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp
index fc355ece3..fda5a79c9 100644
--- a/Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp
+++ b/Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp
@@ -67,43 +67,43 @@
 
 /* init sequence from https://github.com/adafruit/ST7565-LCD/blob/master/ST7565/ST7565.cpp */
 static const uint8_t u8g_dev_st7565_64128n_HAL_init_seq[] PROGMEM = {
-   U8G_ESC_CS(0),       // disable chip
-    U8G_ESC_ADR(0),     // instruction mode
-    U8G_ESC_CS(1),      // enable chip
-    U8G_ESC_RST(15),    // do reset low pulse with (15*16)+2 milliseconds (=maximum delay)*/
+  U8G_ESC_CS(0),       // disable chip
+  U8G_ESC_ADR(0),     // instruction mode
+  U8G_ESC_CS(1),      // enable chip
+  U8G_ESC_RST(15),    // do reset low pulse with (15*16)+2 milliseconds (=maximum delay)*/
 
-    0x0A2,              // 0x0A2: LCD bias 1/9 (according to Displaytech 64128N datasheet)
-    0x0A0,              // Normal ADC Select (according to Displaytech 64128N datasheet)
+  0x0A2,              // 0x0A2: LCD bias 1/9 (according to Displaytech 64128N datasheet)
+  0x0A0,              // Normal ADC Select (according to Displaytech 64128N datasheet)
 
-    0x0C8,              // common output mode: set scan direction normal operation/SHL Select, 0x0C0 --> SHL = 0, normal, 0x0C8 --> SHL = 1
-    0x040,              // Display start line for Displaytech 64128N
+  0x0C8,              // common output mode: set scan direction normal operation/SHL Select, 0x0C0 --> SHL = 0, normal, 0x0C8 --> SHL = 1
+  0x040,              // Display start line for Displaytech 64128N
 
-    0x028 | 0x04,       // power control: turn on voltage converter
-    U8G_ESC_DLY(50),    // delay 50 ms
+  0x028 | 0x04,       // power control: turn on voltage converter
+  U8G_ESC_DLY(50),    // delay 50 ms
 
-    0x028 | 0x06,       // power control: turn on voltage regulator
-    U8G_ESC_DLY(50),    // delay 50 ms
+  0x028 | 0x06,       // power control: turn on voltage regulator
+  U8G_ESC_DLY(50),    // delay 50 ms
 
-    0x028 | 0x07,       // power control: turn on voltage follower
-    U8G_ESC_DLY(50),    // delay 50 ms
+  0x028 | 0x07,       // power control: turn on voltage follower
+  U8G_ESC_DLY(50),    // delay 50 ms
 
-    0x010,              // Set V0 voltage resistor ratio. Setting for controlling brightness of Displaytech 64128N
+  0x010,              // Set V0 voltage resistor ratio. Setting for controlling brightness of Displaytech 64128N
 
-    0x0A6,              // display normal, bit val 0: LCD pixel off.
+  0x0A6,              // display normal, bit val 0: LCD pixel off.
 
-    0x081,              // set contrast
-    0x01E,              // Contrast value. Setting for controlling brightness of Displaytech 64128N
+  0x081,              // set contrast
+  0x01E,              // Contrast value. Setting for controlling brightness of Displaytech 64128N
 
 
-    0x0AF,              // display on
+  0x0AF,              // display on
 
-    U8G_ESC_DLY(100),   // delay 100 ms
-    0x0A5,              // display all points, ST7565
-    U8G_ESC_DLY(100),   // delay 100 ms
-    U8G_ESC_DLY(100),   // delay 100 ms
-    0x0A4,              // normal display
-    U8G_ESC_CS(0),      // disable chip
-    U8G_ESC_END         // end of sequence
+  U8G_ESC_DLY(100),   // delay 100 ms
+  0x0A5,              // display all points, ST7565
+  U8G_ESC_DLY(100),   // delay 100 ms
+  U8G_ESC_DLY(100),   // delay 100 ms
+  0x0A4,              // normal display
+  U8G_ESC_CS(0),      // disable chip
+  U8G_ESC_END         // end of sequence
 };
 
 static const uint8_t u8g_dev_st7565_64128n_HAL_data_start[] PROGMEM = {
@@ -211,7 +211,6 @@ uint8_t u8g_dev_st7565_64128n_HAL_2x_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg,
   return u8g_dev_pb16v1_base_fn(u8g, dev, msg, arg);
 }
 
-
 U8G_PB_DEV(u8g_dev_st7565_64128n_HAL_sw_spi, WIDTH, HEIGHT, PAGE_HEIGHT, u8g_dev_st7565_64128n_HAL_fn, U8G_COM_HAL_SW_SPI_FN);
 
 uint8_t u8g_dev_st7565_64128n_HAL_2x_buf[WIDTH*2] U8G_NOCOMMON ;
diff --git a/Marlin/src/lcd/dogm/u8g_dev_st7920_128x64_HAL.cpp b/Marlin/src/lcd/dogm/u8g_dev_st7920_128x64_HAL.cpp
index 518168cff..86a9fd110 100644
--- a/Marlin/src/lcd/dogm/u8g_dev_st7920_128x64_HAL.cpp
+++ b/Marlin/src/lcd/dogm/u8g_dev_st7920_128x64_HAL.cpp
@@ -53,7 +53,7 @@
  * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 
-#include "../../inc/MarlinConfig.h"
+#include "../../inc/MarlinConfigPre.h"
 
 #if ENABLED(DOGLCD)
 
diff --git a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp
index 89f74584a..e58bb34fa 100644
--- a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp
+++ b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp
@@ -57,7 +57,7 @@
 
 */
 
-#include "../../inc/MarlinConfig.h"
+#include "../../inc/MarlinConfigPre.h"
 
 #if ENABLED(DOGLCD)
 
@@ -108,10 +108,8 @@ static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = {
   U8G_ESC_END                /* end of sequence */
 };
 
-uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg)
-{
-  switch(msg)
-  {
+uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) {
+  switch(msg) {
     case U8G_DEV_MSG_INIT:
       u8g_InitCom(u8g, dev, U8G_SPI_CLK_CYCLE_300NS);
       u8g_WriteEscSeqP(u8g, dev, u8g_dev_uc1701_mini12864_HAL_init_seq);
@@ -140,10 +138,8 @@ uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg,
   return u8g_dev_pb8v1_base_fn(u8g, dev, msg, arg);
 }
 
-uint8_t u8g_dev_uc1701_mini12864_HAL_2x_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg)
-{
-  switch(msg)
-  {
+uint8_t u8g_dev_uc1701_mini12864_HAL_2x_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) {
+  switch(msg) {
     case U8G_DEV_MSG_INIT:
       u8g_InitCom(u8g, dev, U8G_SPI_CLK_CYCLE_300NS);
       u8g_WriteEscSeqP(u8g, dev, u8g_dev_uc1701_mini12864_HAL_init_seq);
diff --git a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp
index f5926b020..71f61a08c 100644
--- a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp
+++ b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp
@@ -24,12 +24,13 @@
 // file u8g_dev_st7920_128x64_HAL.cpp for the HAL version.
 
 #include "../../inc/MarlinConfig.h"
-#include "../../HAL/Delay.h"
 
 #if ENABLED(U8GLIB_ST7920)
 
 #if !(defined(U8G_HAL_LINKS) || defined(__SAM3X8E__))
 
+#include "../../HAL/Delay.h"
+
 #define ST7920_CLK_PIN  LCD_PINS_D4
 #define ST7920_DAT_PIN  LCD_PINS_ENABLE
 #define ST7920_CS_PIN   LCD_PINS_RS
diff --git a/Marlin/src/lcd/lcdprint_u8g.cpp b/Marlin/src/lcd/lcdprint_u8g.cpp
index c82c3fd0a..7ce728902 100644
--- a/Marlin/src/lcd/lcdprint_u8g.cpp
+++ b/Marlin/src/lcd/lcdprint_u8g.cpp
@@ -8,11 +8,8 @@
  */
 
 #include "../inc/MarlinConfigPre.h"
-#include "../inc/MarlinConfig.h"
 
-#define USE_LCDPRINT_U8G ENABLED(ULTRA_LCD) && ENABLED(DOGLCD)
-
-#if USE_LCDPRINT_U8G
+#if ENABLED(DOGLCD)
 
 #include <U8glib.h>
 extern U8GLIB *pu8g;
@@ -72,9 +69,9 @@ int lcd_put_u8str_max_rom(const char * utf8_str_P, pixel_len_t max_length) {
   return ret;
 }
 
-#else // !USE_LCDPRINT_U8G
+#else // !ULTRA_LCD
 
-#define _lcd_write(a) TRACE("Write LCD: %c (%d)", (a), (int)(a));
-#define _lcd_setcursor(col, row) TRACE("Set cursor LCD: (%d,%d)", (col), (row));
+  #define _lcd_write(a) TRACE("Write LCD: %c (%d)", (a), (int)(a));
+  #define _lcd_setcursor(col, row) TRACE("Set cursor LCD: (%d,%d)", (col), (row));
 
-#endif // !USE_LCDPRINT_U8G
+#endif // !ULTRA_LCD