From d2bb53702a5b8bc03d6691230f252a21ca3ee375 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Wed, 14 Nov 2018 17:33:04 -0600 Subject: [PATCH] Optimize target_extruder, ignore T with mixing (#12432) * Optimize target_extruder, ignore T with mixing * Give G-code Tn parity with tool_change --- Marlin/src/gcode/config/M200-M205.cpp | 13 +-- Marlin/src/gcode/config/M218.cpp | 4 +- Marlin/src/gcode/config/M221.cpp | 5 +- Marlin/src/gcode/config/M92.cpp | 13 +-- Marlin/src/gcode/control/T.cpp | 14 ++-- Marlin/src/gcode/feature/pause/M600.cpp | 3 +- Marlin/src/gcode/feature/pause/M603.cpp | 3 +- Marlin/src/gcode/feature/pause/M701_M702.cpp | 11 ++- Marlin/src/gcode/feature/trinamic/M906.cpp | 3 +- .../src/gcode/feature/trinamic/M911-M915.cpp | 3 +- Marlin/src/gcode/gcode.cpp | 21 ++--- Marlin/src/gcode/gcode.h | 22 ++--- Marlin/src/gcode/temperature/M104_M109.cpp | 17 +++- Marlin/src/gcode/temperature/M105.cpp | 8 +- Marlin/src/gcode/temperature/M303.cpp | 46 ++++++---- Marlin/src/module/temperature.cpp | 84 ++++++++----------- Marlin/src/module/temperature.h | 4 +- Marlin/src/module/tool_change.cpp | 12 +-- 18 files changed, 149 insertions(+), 137 deletions(-) diff --git a/Marlin/src/gcode/config/M200-M205.cpp b/Marlin/src/gcode/config/M200-M205.cpp index d30f7ba25..f806fd19d 100644 --- a/Marlin/src/gcode/config/M200-M205.cpp +++ b/Marlin/src/gcode/config/M200-M205.cpp @@ -34,7 +34,8 @@ */ void GcodeSuite::M200() { - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; if (parser.seen('D')) { // setting any extruder filament size disables volumetric on the assumption that @@ -55,11 +56,12 @@ */ void GcodeSuite::M201() { - GET_TARGET_EXTRUDER(); + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; LOOP_XYZE(i) { if (parser.seen(axis_codes[i])) { - const uint8_t a = i + (i == E_AXIS ? TARGET_EXTRUDER : 0); + const uint8_t a = (i == E_AXIS ? E_AXIS_N(target_extruder) : i); planner.settings.max_acceleration_mm_per_s2[a] = parser.value_axis_units((AxisEnum)a); } } @@ -74,11 +76,12 @@ void GcodeSuite::M201() { */ void GcodeSuite::M203() { - GET_TARGET_EXTRUDER(); + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; LOOP_XYZE(i) if (parser.seen(axis_codes[i])) { - const uint8_t a = i + (i == E_AXIS ? TARGET_EXTRUDER : 0); + const uint8_t a = (i == E_AXIS ? E_AXIS_N(target_extruder) : i); planner.settings.max_feedrate_mm_s[a] = parser.value_axis_units((AxisEnum)a); } } diff --git a/Marlin/src/gcode/config/M218.cpp b/Marlin/src/gcode/config/M218.cpp index 4f7a353ae..df17bd564 100644 --- a/Marlin/src/gcode/config/M218.cpp +++ b/Marlin/src/gcode/config/M218.cpp @@ -40,7 +40,9 @@ * Z */ void GcodeSuite::M218() { - if (get_target_extruder_from_command() || target_extruder == 0) return; + + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; if (parser.seenval('X')) hotend_offset[X_AXIS][target_extruder] = parser.value_linear_units(); if (parser.seenval('Y')) hotend_offset[Y_AXIS][target_extruder] = parser.value_linear_units(); diff --git a/Marlin/src/gcode/config/M221.cpp b/Marlin/src/gcode/config/M221.cpp index e5d4204f5..712942786 100644 --- a/Marlin/src/gcode/config/M221.cpp +++ b/Marlin/src/gcode/config/M221.cpp @@ -27,7 +27,10 @@ * M221: Set extrusion percentage (M221 T0 S95) */ void GcodeSuite::M221() { - if (get_target_extruder_from_command()) return; + + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; + if (parser.seenval('S')) { planner.flow_percentage[target_extruder] = parser.value_int(); planner.refresh_e_factor(target_extruder); diff --git a/Marlin/src/gcode/config/M92.cpp b/Marlin/src/gcode/config/M92.cpp index e0dd1eb26..cb438d414 100644 --- a/Marlin/src/gcode/config/M92.cpp +++ b/Marlin/src/gcode/config/M92.cpp @@ -31,21 +31,22 @@ */ void GcodeSuite::M92() { - GET_TARGET_EXTRUDER(); + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; LOOP_XYZE(i) { if (parser.seen(axis_codes[i])) { if (i == E_AXIS) { - const float value = parser.value_per_axis_units((AxisEnum)(E_AXIS + TARGET_EXTRUDER)); + const float value = parser.value_per_axis_units((AxisEnum)(E_AXIS_N(target_extruder))); if (value < 20) { - float factor = planner.settings.axis_steps_per_mm[E_AXIS + TARGET_EXTRUDER] / value; // increase e constants if M92 E14 is given for netfab. + float factor = planner.settings.axis_steps_per_mm[E_AXIS_N(target_extruder)] / value; // increase e constants if M92 E14 is given for netfab. #if HAS_CLASSIC_JERK && (DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE)) planner.max_jerk[E_AXIS] *= factor; #endif - planner.settings.max_feedrate_mm_s[E_AXIS + TARGET_EXTRUDER] *= factor; - planner.max_acceleration_steps_per_s2[E_AXIS + TARGET_EXTRUDER] *= factor; + planner.settings.max_feedrate_mm_s[E_AXIS_N(target_extruder)] *= factor; + planner.max_acceleration_steps_per_s2[E_AXIS_N(target_extruder)] *= factor; } - planner.settings.axis_steps_per_mm[E_AXIS + TARGET_EXTRUDER] = value; + planner.settings.axis_steps_per_mm[E_AXIS_N(target_extruder)] = value; } else { planner.settings.axis_steps_per_mm[i] = parser.value_per_axis_units((AxisEnum)i); diff --git a/Marlin/src/gcode/control/T.cpp b/Marlin/src/gcode/control/T.cpp index 3911b8fbc..58febbd6d 100644 --- a/Marlin/src/gcode/control/T.cpp +++ b/Marlin/src/gcode/control/T.cpp @@ -33,27 +33,27 @@ * F[units/min] Set the movement feedrate * S1 Don't move the tool in XY after change */ -void GcodeSuite::T(const uint8_t tmp_extruder) { +void GcodeSuite::T(const uint8_t tool_index) { #if ENABLED(DEBUG_LEVELING_FEATURE) if (DEBUGGING(LEVELING)) { - SERIAL_ECHOPAIR(">>> T(", tmp_extruder); + SERIAL_ECHOPAIR(">>> T(", tool_index); SERIAL_CHAR(')'); SERIAL_EOL(); DEBUG_POS("BEFORE", current_position); } #endif - #if HOTENDS == 1 || (ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1) + #if EXTRUDERS < 2 - tool_change(tmp_extruder); + tool_change(tool_index); - #elif HOTENDS > 1 + #else tool_change( - tmp_extruder, + tool_index, MMM_TO_MMS(parser.linearval('F')), - (tmp_extruder == active_extruder) || parser.boolval('S') + (tool_index == active_extruder) || parser.boolval('S') ); #endif diff --git a/Marlin/src/gcode/feature/pause/M600.cpp b/Marlin/src/gcode/feature/pause/M600.cpp index 92b431c43..850bbb344 100644 --- a/Marlin/src/gcode/feature/pause/M600.cpp +++ b/Marlin/src/gcode/feature/pause/M600.cpp @@ -54,7 +54,8 @@ void GcodeSuite::M600() { point_t park_point = NOZZLE_PARK_POINT; - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; #if ENABLED(DUAL_X_CARRIAGE) int8_t DXC_ext = target_extruder; diff --git a/Marlin/src/gcode/feature/pause/M603.cpp b/Marlin/src/gcode/feature/pause/M603.cpp index 08236187d..e4a5e5eaa 100644 --- a/Marlin/src/gcode/feature/pause/M603.cpp +++ b/Marlin/src/gcode/feature/pause/M603.cpp @@ -43,7 +43,8 @@ */ void GcodeSuite::M603() { - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; // Unload length if (parser.seen('U')) { diff --git a/Marlin/src/gcode/feature/pause/M701_M702.cpp b/Marlin/src/gcode/feature/pause/M701_M702.cpp index a50b4efe7..fa9be253e 100644 --- a/Marlin/src/gcode/feature/pause/M701_M702.cpp +++ b/Marlin/src/gcode/feature/pause/M701_M702.cpp @@ -55,7 +55,9 @@ void GcodeSuite::M701() { if (axis_unhomed_error()) park_point.z = 0; #endif - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; + // Z axis lift if (parser.seenval('Z')) park_point.z = parser.linearval('Z'); @@ -121,7 +123,8 @@ void GcodeSuite::M702() { if (axis_unhomed_error()) park_point.z = 0; #endif - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; // Z axis lift if (parser.seenval('Z')) park_point.z = parser.linearval('Z'); @@ -154,8 +157,8 @@ void GcodeSuite::M702() { #endif { // Unload length - const float unload_length = -ABS(parser.seen('U') ? parser.value_axis_units(E_AXIS) : - fc_settings[target_extruder].unload_length); + const float unload_length = -ABS(parser.seen('U') ? parser.value_axis_units(E_AXIS) + : fc_settings[target_extruder].unload_length); unload_filament(unload_length, true, ADVANCED_PAUSE_MODE_UNLOAD_FILAMENT); } diff --git a/Marlin/src/gcode/feature/trinamic/M906.cpp b/Marlin/src/gcode/feature/trinamic/M906.cpp index 66f8efd28..1ff282546 100644 --- a/Marlin/src/gcode/feature/trinamic/M906.cpp +++ b/Marlin/src/gcode/feature/trinamic/M906.cpp @@ -73,7 +73,8 @@ void GcodeSuite::M906() { #endif break; case E_AXIS: { - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; switch (target_extruder) { #if AXIS_IS_TMC(E0) case 0: TMC_SET_CURRENT(E0); break; diff --git a/Marlin/src/gcode/feature/trinamic/M911-M915.cpp b/Marlin/src/gcode/feature/trinamic/M911-M915.cpp index 665193028..ee134067e 100644 --- a/Marlin/src/gcode/feature/trinamic/M911-M915.cpp +++ b/Marlin/src/gcode/feature/trinamic/M911-M915.cpp @@ -232,7 +232,8 @@ #endif break; case E_AXIS: { - if (get_target_extruder_from_command()) return; + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; switch (target_extruder) { #if AXIS_HAS_STEALTHCHOP(E0) case 0: TMC_SET_PWMTHRS_E(0); break; diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp index e6bec1f85..bdb65a4a7 100644 --- a/Marlin/src/gcode/gcode.cpp +++ b/Marlin/src/gcode/gcode.cpp @@ -38,7 +38,6 @@ GcodeSuite gcode; #include "../Marlin.h" // for idle() and suspend_auto_report -uint8_t GcodeSuite::target_extruder; millis_t GcodeSuite::previous_move_ms; bool GcodeSuite::axis_relative_modes[] = AXIS_RELATIVE_MODES; @@ -58,11 +57,10 @@ bool GcodeSuite::axis_relative_modes[] = AXIS_RELATIVE_MODES; #endif /** - * Set target_extruder from the T parameter or the active_extruder - * - * Returns TRUE if the target is invalid + * Get the target extruder from the T parameter or the active_extruder + * Return -1 if the T parameter is out of range */ -bool GcodeSuite::get_target_extruder_from_command() { +int8_t GcodeSuite::get_target_extruder_from_command() { if (parser.seenval('T')) { const int8_t e = parser.value_byte(); if (e >= EXTRUDERS) { @@ -70,14 +68,11 @@ bool GcodeSuite::get_target_extruder_from_command() { SERIAL_CHAR('M'); SERIAL_ECHO(parser.codenum); SERIAL_ECHOLNPAIR(" " MSG_INVALID_EXTRUDER " ", e); - return true; + return -1; } - target_extruder = e; + return e; } - else - target_extruder = active_extruder; - - return false; + return active_extruder; } /** @@ -539,7 +534,9 @@ void GcodeSuite::process_parsed_command( case 302: M302(); break; // M302: Allow cold extrudes (set the minimum extrude temperature) #endif - case 303: M303(); break; // M303: PID autotune + #if HAS_PID_HEATING + case 303: M303(); break; // M303: PID autotune + #endif #if ENABLED(MORGAN_SCARA) case 360: if (M360()) return; break; // M360: SCARA Theta pos1 diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h index 9ef63d111..375a6f9ae 100644 --- a/Marlin/src/gcode/gcode.h +++ b/Marlin/src/gcode/gcode.h @@ -267,8 +267,6 @@ public: GcodeSuite() {} - static uint8_t target_extruder; - static bool axis_relative_modes[]; #if ENABLED(CNC_WORKSPACE_PLANES) @@ -290,8 +288,9 @@ public: static millis_t previous_move_ms; FORCE_INLINE static void reset_stepper_timeout() { previous_move_ms = millis(); } - static bool get_target_extruder_from_command(); + static int8_t get_target_extruder_from_command(); static void get_destination_from_command(); + static void process_parsed_command( #if USE_EXECUTE_COMMANDS_IMMEDIATE const bool no_ok = false @@ -306,17 +305,6 @@ public: FORCE_INLINE static void home_all_axes() { G28(true); } - /** - * Multi-stepper support for M92, M201, M203 - */ - #if ENABLED(DISTINCT_E_FACTORS) - #define GET_TARGET_EXTRUDER() if (gcode.get_target_extruder_from_command()) return - #define TARGET_EXTRUDER gcode.target_extruder - #else - #define GET_TARGET_EXTRUDER() NOOP - #define TARGET_EXTRUDER 0 - #endif - #if ENABLED(HOST_KEEPALIVE_FEATURE) /** * States for managing Marlin and host communication @@ -669,7 +657,9 @@ private: static void M302(); #endif - static void M303(); + #if HAS_PID_HEATING + static void M303(); + #endif #if ENABLED(PIDTEMPBED) static void M304(); @@ -832,7 +822,7 @@ private: static void M999(); - static void T(const uint8_t tmp_extruder); + static void T(const uint8_t tool_index); }; diff --git a/Marlin/src/gcode/temperature/M104_M109.cpp b/Marlin/src/gcode/temperature/M104_M109.cpp index c7499624c..916c6efee 100644 --- a/Marlin/src/gcode/temperature/M104_M109.cpp +++ b/Marlin/src/gcode/temperature/M104_M109.cpp @@ -39,10 +39,15 @@ * M104: Set hot end temperature */ void GcodeSuite::M104() { - if (get_target_extruder_from_command()) return; + if (DEBUGGING(DRYRUN)) return; - const uint8_t e = target_extruder; + #if ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1 + constexpr int8_t e = 0; + #else + const int8_t e = get_target_extruder_from_command(); + if (e < 0) return; + #endif if (parser.seenval('S')) { const int16_t temp = parser.value_celsius(); @@ -82,9 +87,15 @@ void GcodeSuite::M104() { */ void GcodeSuite::M109() { - if (get_target_extruder_from_command()) return; if (DEBUGGING(DRYRUN)) return; + #if ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1 + constexpr int8_t target_extruder = 0; + #else + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; + #endif + const bool no_wait_for_cooling = parser.seenval('S'), set_temp = no_wait_for_cooling || parser.seenval('R'); if (set_temp) { diff --git a/Marlin/src/gcode/temperature/M105.cpp b/Marlin/src/gcode/temperature/M105.cpp index 4216c417e..c0678c03c 100644 --- a/Marlin/src/gcode/temperature/M105.cpp +++ b/Marlin/src/gcode/temperature/M105.cpp @@ -31,7 +31,9 @@ * M105: Read hot end and bed temperature */ void GcodeSuite::M105() { - if (get_target_extruder_from_command()) return; + + const int8_t target_extruder = get_target_extruder_from_command(); + if (target_extruder < 0) return; #if NUM_SERIAL > 1 const int16_t port = command_queue_port[cmd_queue_index_r]; @@ -39,9 +41,9 @@ void GcodeSuite::M105() { #if HAS_TEMP_SENSOR SERIAL_PROTOCOLPGM_P(port, MSG_OK); - thermalManager.print_heaterstates( + thermalManager.print_heater_states(target_extruder #if NUM_SERIAL > 1 - port + , port #endif ); #else // !HAS_TEMP_SENSOR diff --git a/Marlin/src/gcode/temperature/M303.cpp b/Marlin/src/gcode/temperature/M303.cpp index 583ea9d7e..8473ecd20 100644 --- a/Marlin/src/gcode/temperature/M303.cpp +++ b/Marlin/src/gcode/temperature/M303.cpp @@ -20,6 +20,10 @@ * */ +#include "../../inc/MarlinConfig.h" + +#if HAS_PID_HEATING + #include "../gcode.h" #include "../../module/temperature.h" @@ -32,26 +36,36 @@ * U with a non-zero value will apply the result to current settings */ void GcodeSuite::M303() { - #if HAS_PID_HEATING - const int e = parser.intval('E'), c = parser.intval('C', 5); - const bool u = parser.boolval('U'); - - int16_t temp = parser.celsiusval('S', e < 0 ? 70 : 150); - if (WITHIN(e, 0, HOTENDS - 1)) - target_extruder = e; + const int8_t e = parser.byteval('E'); - #if DISABLED(BUSY_WHILE_HEATING) - KEEPALIVE_STATE(NOT_BUSY); + if (!WITHIN(e, 0 + #if ENABLED(PIDTEMPBED) + -1 #endif + , + #if ENABLED(PIDTEMP) + HOTENDS + #endif + -1 + )) { + SERIAL_ECHOLNPGM(MSG_PID_BAD_EXTRUDER_NUM); + return; + } - thermalManager.PID_autotune(temp, e, c, u); + const int c = parser.intval('C', 5); + const bool u = parser.boolval('U'); + const int16_t temp = parser.celsiusval('S', e < 0 ? 70 : 150); - #if DISABLED(BUSY_WHILE_HEATING) - KEEPALIVE_STATE(IN_HANDLER); - #endif - #else - SERIAL_ERROR_START(); - SERIAL_ERRORLNPGM(MSG_ERR_M303_DISABLED); + #if DISABLED(BUSY_WHILE_HEATING) + KEEPALIVE_STATE(NOT_BUSY); + #endif + + thermalManager.PID_autotune(temp, e, c, u); + + #if DISABLED(BUSY_WHILE_HEATING) + KEEPALIVE_STATE(IN_HANDLER); #endif } + +#endif // HAS_PID_HEATING diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 475d38aad..72abb12f4 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -236,7 +236,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; * Alternately heat and cool the nozzle, observing its behavior to * determine the best PID values to achieve a stable temperature. */ - void Temperature::PID_autotune(const float &target, const int8_t hotend, const int8_t ncycles, const bool set_result/*=false*/) { + void Temperature::PID_autotune(const float &target, const int8_t heater, const int8_t ncycles, const bool set_result/*=false*/) { float current = 0.0; int cycles = 0; bool heating = true; @@ -249,10 +249,10 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; float max = 0, min = 10000; #if HAS_PID_FOR_BOTH - #define GHV(B,H) (hotend < 0 ? (B) : (H)) - #define SHV(S,B,H) do{ if (hotend < 0) S##_bed = B; else S [hotend] = H; }while(0) - #define ONHEATINGSTART() (hotend < 0 ? printerEventLEDs.onBedHeatingStart() : printerEventLEDs.onHotendHeatingStart()) - #define ONHEATING(S,C,T) do{ if (hotend < 0) printerEventLEDs.onBedHeating(S,C,T); else printerEventLEDs.onHotendHeating(S,C,T); }while(0) + #define GHV(B,H) (heater < 0 ? (B) : (H)) + #define SHV(S,B,H) do{ if (heater < 0) S##_bed = B; else S [heater] = H; }while(0) + #define ONHEATINGSTART() (heater < 0 ? printerEventLEDs.onBedHeatingStart() : printerEventLEDs.onHotendHeatingStart()) + #define ONHEATING(S,C,T) do{ if (heater < 0) printerEventLEDs.onBedHeating(S,C,T); else printerEventLEDs.onHotendHeating(S,C,T); }while(0) #elif ENABLED(PIDTEMPBED) #define GHV(B,H) B #define SHV(S,B,H) (S##_bed = B) @@ -260,7 +260,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; #define ONHEATING(S,C,T) printerEventLEDs.onBedHeating(S,C,T) #else #define GHV(B,H) H - #define SHV(S,B,H) (S [hotend] = H) + #define SHV(S,B,H) (S [heater] = H) #define ONHEATINGSTART() printerEventLEDs.onHotendHeatingStart() #define ONHEATING(S,C,T) printerEventLEDs.onHotendHeating(S,C,T) #endif @@ -268,7 +268,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; #if WATCH_THE_BED || WATCH_HOTENDS #define HAS_TP_BED (ENABLED(THERMAL_PROTECTION_BED) && ENABLED(PIDTEMPBED)) #if HAS_TP_BED && ENABLED(THERMAL_PROTECTION_HOTENDS) && ENABLED(PIDTEMP) - #define GTV(B,H) (hotend < 0 ? (B) : (H)) + #define GTV(B,H) (heater < 0 ? (B) : (H)) #elif HAS_TP_BED #define GTV(B,H) (B) #else @@ -286,22 +286,6 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; next_auto_fan_check_ms = next_temp_ms + 2500UL; #endif - #if ENABLED(PIDTEMP) - #define _TOP_HOTEND HOTENDS - 1 - #else - #define _TOP_HOTEND -1 - #endif - #if ENABLED(PIDTEMPBED) - #define _BOT_HOTEND -1 - #else - #define _BOT_HOTEND 0 - #endif - - if (!WITHIN(hotend, _BOT_HOTEND, _TOP_HOTEND)) { - SERIAL_ECHOLNPGM(MSG_PID_BAD_EXTRUDER_NUM); - return; - } - SERIAL_ECHOLNPGM(MSG_PID_AUTOTUNE_START); disable_all_heaters(); @@ -310,7 +294,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; wait_for_heatup = true; // Can be interrupted with M108 #if ENABLED(PRINTER_EVENT_LEDS) - const float start_temp = GHV(current_temperature_bed, current_temperature[hotend]); + const float start_temp = GHV(current_temperature_bed, current_temperature[heater]); LEDColor color = ONHEATINGSTART(); #endif @@ -323,7 +307,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; updateTemperaturesFromRawValues(); // Get the current temperature and constrain it - current = GHV(current_temperature_bed, current_temperature[hotend]); + current = GHV(current_temperature_bed, current_temperature[heater]); NOLESS(max, current); NOMORE(min, current); @@ -412,7 +396,7 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; // Report heater states every 2 seconds if (ELAPSED(ms, next_temp_ms)) { #if HAS_TEMP_SENSOR - print_heaterstates(); + print_heater_states(heater >= 0 ? heater : active_extruder); SERIAL_EOL(); #endif next_temp_ms = ms + 2000UL; @@ -423,9 +407,9 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; #if WATCH_THE_BED && WATCH_HOTENDS true #elif WATCH_HOTENDS - hotend >= 0 + heater >= 0 #else - hotend < 0 + heater < 0 #endif ) { if (!heated) { // If not yet reached target... @@ -435,10 +419,10 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; if (current > watch_temp_target) heated = true; // - Flag if target temperature reached } else if (ELAPSED(ms, temp_change_ms)) // Watch timer expired - _temp_error(hotend, PSTR(MSG_T_HEATING_FAILED), TEMP_ERR_PSTR(MSG_HEATING_FAILED_LCD, hotend)); + _temp_error(heater, PSTR(MSG_T_HEATING_FAILED), TEMP_ERR_PSTR(MSG_HEATING_FAILED_LCD, heater)); } else if (current < target - (MAX_OVERSHOOT_PID_AUTOTUNE)) // Heated, then temperature fell too far? - _temp_error(hotend, PSTR(MSG_T_THERMAL_RUNAWAY), TEMP_ERR_PSTR(MSG_THERMAL_RUNAWAY, hotend)); + _temp_error(heater, PSTR(MSG_T_THERMAL_RUNAWAY), TEMP_ERR_PSTR(MSG_THERMAL_RUNAWAY, heater)); } #endif } // every 2 seconds @@ -477,15 +461,15 @@ uint8_t Temperature::soft_pwm_amount[HOTENDS]; }while(0) #define _SET_EXTRUDER_PID() do { \ - PID_PARAM(Kp, hotend) = tune_pid.Kp; \ - PID_PARAM(Ki, hotend) = scalePID_i(tune_pid.Ki); \ - PID_PARAM(Kd, hotend) = scalePID_d(tune_pid.Kd); \ + PID_PARAM(Kp, heater) = tune_pid.Kp; \ + PID_PARAM(Ki, heater) = scalePID_i(tune_pid.Ki); \ + PID_PARAM(Kd, heater) = scalePID_d(tune_pid.Kd); \ updatePID(); }while(0) // Use the result? (As with "M303 U1") if (set_result) { #if HAS_PID_FOR_BOTH - if (hotend < 0) _SET_BED_PID(); else _SET_EXTRUDER_PID(); + if (heater < 0) _SET_BED_PID(); else _SET_EXTRUDER_PID(); #elif ENABLED(PIDTEMP) _SET_EXTRUDER_PID(); #else @@ -575,13 +559,13 @@ int Temperature::getHeaterPower(const int heater) { // // Temperature Error Handlers // -void Temperature::_temp_error(const int8_t e, PGM_P const serial_msg, PGM_P const lcd_msg) { +void Temperature::_temp_error(const int8_t heater, PGM_P const serial_msg, PGM_P const lcd_msg) { static bool killed = false; if (IsRunning()) { SERIAL_ERROR_START(); serialprintPGM(serial_msg); SERIAL_ERRORPGM(MSG_STOPPED_HEATER); - if (e >= 0) SERIAL_ERRORLN((int)e); else SERIAL_ERRORLNPGM(MSG_HEATER_BED); + if (heater >= 0) SERIAL_ERRORLN((int)heater); else SERIAL_ERRORLNPGM(MSG_HEATER_BED); } #if DISABLED(BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE) if (!killed) { @@ -594,12 +578,12 @@ void Temperature::_temp_error(const int8_t e, PGM_P const serial_msg, PGM_P cons #endif } -void Temperature::max_temp_error(const int8_t e) { - _temp_error(e, PSTR(MSG_T_MAXTEMP), TEMP_ERR_PSTR(MSG_ERR_MAXTEMP, e)); +void Temperature::max_temp_error(const int8_t heater) { + _temp_error(heater, PSTR(MSG_T_MAXTEMP), TEMP_ERR_PSTR(MSG_ERR_MAXTEMP, heater)); } -void Temperature::min_temp_error(const int8_t e) { - _temp_error(e, PSTR(MSG_T_MINTEMP), TEMP_ERR_PSTR(MSG_ERR_MINTEMP, e)); +void Temperature::min_temp_error(const int8_t heater) { + _temp_error(heater, PSTR(MSG_T_MINTEMP), TEMP_ERR_PSTR(MSG_ERR_MINTEMP, heater)); } float Temperature::get_pid_output(const int8_t e) { @@ -2346,15 +2330,15 @@ void Temperature::isr() { delay(2); } - void Temperature::print_heaterstates( + void Temperature::print_heater_states(const uint8_t target_extruder #if NUM_SERIAL > 1 - const int8_t port + , const int8_t port #endif ) { #if HAS_TEMP_HOTEND - print_heater_state(degHotend(gcode.target_extruder), degTargetHotend(gcode.target_extruder) + print_heater_state(degHotend(target_extruder), degTargetHotend(target_extruder) #if ENABLED(SHOW_TEMP_ADC_VALUES) - , rawHotendTemp(gcode.target_extruder) + , rawHotendTemp(target_extruder) #endif #if NUM_SERIAL > 1 , port @@ -2392,7 +2376,7 @@ void Temperature::isr() { ); #endif SERIAL_PROTOCOLPGM_P(port, " @:"); - SERIAL_PROTOCOL_P(port, getHeaterPower(gcode.target_extruder)); + SERIAL_PROTOCOL_P(port, getHeaterPower(target_extruder)); #if HAS_HEATED_BED SERIAL_PROTOCOLPGM_P(port, " B@:"); SERIAL_PROTOCOL_P(port, getHeaterPower(-1)); @@ -2414,7 +2398,7 @@ void Temperature::isr() { void Temperature::auto_report_temperatures() { if (auto_report_temp_interval && ELAPSED(millis(), next_temp_report_ms)) { next_temp_report_ms = millis() + 1000UL * auto_report_temp_interval; - print_heaterstates(); + print_heater_states(active_extruder); SERIAL_EOL(); } } @@ -2480,9 +2464,9 @@ void Temperature::isr() { } now = millis(); - if (ELAPSED(now, next_temp_ms)) { //Print temp & remaining time every 1s while waiting + if (ELAPSED(now, next_temp_ms)) { // Print temp & remaining time every 1s while waiting next_temp_ms = now + 1000UL; - print_heaterstates(); + print_heater_states(target_extruder); #if TEMP_RESIDENCY_TIME > 0 SERIAL_PROTOCOLPGM(" W:"); if (residency_start_ms) @@ -2587,8 +2571,6 @@ void Temperature::isr() { KEEPALIVE_STATE(NOT_BUSY); #endif - gcode.target_extruder = active_extruder; // for print_heaterstates - #if ENABLED(PRINTER_EVENT_LEDS) const float start_temp = degBed(); printerEventLEDs.onBedHeatingStart(); @@ -2607,7 +2589,7 @@ void Temperature::isr() { now = millis(); if (ELAPSED(now, next_temp_ms)) { //Print Temp Reading every 1 second while heating up. next_temp_ms = now + 1000UL; - print_heaterstates(); + print_heater_states(active_extruder); #if TEMP_BED_RESIDENCY_TIME > 0 SERIAL_PROTOCOLPGM(" W:"); if (residency_start_ms) diff --git a/Marlin/src/module/temperature.h b/Marlin/src/module/temperature.h index 9672707da..963b219c5 100644 --- a/Marlin/src/module/temperature.h +++ b/Marlin/src/module/temperature.h @@ -601,9 +601,9 @@ class Temperature { #endif // HEATER_IDLE_HANDLER #if HAS_TEMP_SENSOR - static void print_heaterstates( + static void print_heater_states(const uint8_t target_extruder #if NUM_SERIAL > 1 - const int8_t port = -1 + , const int8_t port = -1 #endif ); #if ENABLED(AUTO_REPORT_TEMPERATURES) diff --git a/Marlin/src/module/tool_change.cpp b/Marlin/src/module/tool_change.cpp index a8a2ba3cf..b716c0192 100644 --- a/Marlin/src/module/tool_change.cpp +++ b/Marlin/src/module/tool_change.cpp @@ -500,8 +500,8 @@ inline void invalid_extruder_error(const uint8_t e) { void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool no_move/*=false*/) { #if ENABLED(MIXING_EXTRUDER) - UNUSED(fr_mm_s); - UNUSED(no_move); + UNUSED(fr_mm_s); UNUSED(no_move); + if (tmp_extruder >= MIXING_VIRTUAL_TOOLS) return invalid_extruder_error(tmp_extruder); @@ -512,12 +512,12 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n #elif EXTRUDERS < 2 - UNUSED(fr_mm_s); - UNUSED(no_move); + UNUSED(fr_mm_s); UNUSED(no_move); + if (tmp_extruder) invalid_extruder_error(tmp_extruder); return; - #else + #else // EXTRUDERS > 1 planner.synchronize(); @@ -751,5 +751,5 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR(MSG_ACTIVE_EXTRUDER, int(active_extruder)); - #endif // EXTRUDERS <= 1 && (!MIXING_EXTRUDER || MIXING_VIRTUAL_TOOLS <= 1) + #endif // EXTRUDERS > 1 }