diff --git a/Marlin/src/HAL/HAL_DUE/HAL_Due.h b/Marlin/src/HAL/HAL_DUE/HAL_Due.h index e1a9094d7..0aa7ab437 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_Due.h +++ b/Marlin/src/HAL/HAL_DUE/HAL_Due.h @@ -29,37 +29,35 @@ #ifndef _HAL_DUE_H #define _HAL_DUE_H -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "Arduino.h" #include "fastio_Due.h" #include "watchdog_Due.h" - #include "HAL_timers_Due.h" -// -------------------------------------------------------------------------- +// // Defines -// -------------------------------------------------------------------------- +// #if SERIAL_PORT == -1 #define MYSERIAL SerialUSB #elif SERIAL_PORT == 0 - #define MYSERIAL Serial + #define MYSERIAL customizedSerial #elif SERIAL_PORT == 1 - #define MYSERIAL Serial1 + #define MYSERIAL customizedSerial #elif SERIAL_PORT == 2 - #define MYSERIAL Serial2 + #define MYSERIAL customizedSerial #elif SERIAL_PORT == 3 - #define MYSERIAL Serial3 + #define MYSERIAL customizedSerial #endif #define _BV(bit) (1 << (bit)) +// We need the previous define before the include, or compilation bombs... +#include "MarlinSerial_Due.h" + #ifndef analogInputToDigitalPin #define analogInputToDigitalPin(p) ((p < 12u) ? (p) + 54u : -1) #endif @@ -102,46 +100,43 @@ typedef int8_t pin_t; // Public Variables // -------------------------------------------------------------------------- -/** result of last ADC conversion */ -extern uint16_t HAL_adc_result; +extern uint16_t HAL_adc_result; // result of last ADC conversion -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -// Disable interrupts -void cli(void); - -// Enable interrupts -void sei(void); - -/** clear reset reason */ -void HAL_clear_reset_source (void); +void cli(void); // Disable interrupts +void sei(void); // Enable interrupts -/** reset reason */ -uint8_t HAL_get_reset_source (void); +void HAL_clear_reset_source(void); // clear reset reason +uint8_t HAL_get_reset_source(void); // get reset reason void _delay_ms(const int delay); int freeMemory(void); -// SPI: Extended functions which take a channel number (hardware SPI only) -/** Write single byte to specified SPI channel */ +/** + * SPI: Extended functions taking a channel number (hardware SPI only) + */ + +// Write single byte to specified SPI channel void spiSend(uint32_t chan, byte b); -/** Write buffer to specified SPI channel */ + +// Write buffer to specified SPI channel void spiSend(uint32_t chan, const uint8_t* buf, size_t n); -/** Read single byte from specified SPI channel */ + +// Read single byte from specified SPI channel uint8_t spiRec(uint32_t chan); +/** + * EEPROM + */ -// EEPROM void eeprom_write_byte(unsigned char *pos, unsigned char value); unsigned char eeprom_read_byte(unsigned char *pos); void eeprom_read_block (void *__dst, const void *__src, size_t __n); void eeprom_update_block (const void *__src, void *__dst, size_t __n); - -// ADC +/** + * ADC + */ #define HAL_ANALOG_SELECT(pin) @@ -150,20 +145,13 @@ inline void HAL_adc_init(void) {}//todo #define HAL_START_ADC(pin) HAL_adc_start_conversion(pin) #define HAL_READ_ADC HAL_adc_result - void HAL_adc_start_conversion(const uint8_t adc_pin); - uint16_t HAL_adc_get_result(void); - -// uint16_t HAL_getAdcReading(uint8_t chan); - void HAL_startAdcConversion(uint8_t chan); uint8_t HAL_pinToAdcChannel(int pin); - uint16_t HAL_getAdcFreerun(uint8_t chan, bool wait_for_conversion = false); //uint16_t HAL_getAdcSuperSample(uint8_t chan); - void HAL_enable_AdcFreerun(void); //void HAL_disable_AdcFreerun(uint8_t chan); @@ -171,9 +159,4 @@ void HAL_enable_AdcFreerun(void); #define GET_PIN_MAP_INDEX(pin) pin #define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval) -// -------------------------------------------------------------------------- -// -// -------------------------------------------------------------------------- - #endif // _HAL_DUE_H - diff --git a/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.cpp b/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.cpp new file mode 100644 index 000000000..0acfb9942 --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.cpp @@ -0,0 +1,680 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * MarlinSerial_Due.cpp - Hardware serial library for Arduino DUE + * Copyright (c) 2017 Eduardo José Tagle. All right reserved + * Based on MarlinSerial for AVR, copyright (c) 2006 Nicholas Zambetti. All right reserved. + */ +#ifdef ARDUINO_ARCH_SAM + +#include "../../inc/MarlinConfig.h" + +#include "MarlinSerial_Due.h" +#include "InterruptVectors_Due.h" +#include "../../Marlin.h" + +// Based on selected port, use the proper configuration +#if SERIAL_PORT == 0 + #define HWUART UART + #define HWUART_IRQ UART_IRQn + #define HWUART_IRQ_ID ID_UART +#elif SERIAL_PORT == 1 + #define HWUART USART0 + #define HWUART_IRQ USART0_IRQn + #define HWUART_IRQ_ID ID_USART0 +#elif SERIAL_PORT == 2 + #define HWUART USART1 + #define HWUART_IRQ USART1_IRQn + #define HWUART_IRQ_ID ID_USART1 +#elif SERIAL_PORT == 3 + #define HWUART USART3 + #define HWUART_IRQ USART3_IRQn + #define HWUART_IRQ_ID ID_USART3 +#endif + +struct ring_buffer_r { + unsigned char buffer[RX_BUFFER_SIZE]; + volatile ring_buffer_pos_t head, tail; +}; + +#if TX_BUFFER_SIZE > 0 + struct ring_buffer_t { + unsigned char buffer[TX_BUFFER_SIZE]; + volatile uint8_t head, tail; + }; +#endif + +ring_buffer_r rx_buffer = { { 0 }, 0, 0 }; +#if TX_BUFFER_SIZE > 0 + ring_buffer_t tx_buffer = { { 0 }, 0, 0 }; + static bool _written; +#endif + +#if ENABLED(SERIAL_XON_XOFF) + constexpr uint8_t XON_XOFF_CHAR_SENT = 0x80; // XON / XOFF Character was sent + constexpr uint8_t XON_XOFF_CHAR_MASK = 0x1F; // XON / XOFF character to send + // XON / XOFF character definitions + constexpr uint8_t XON_CHAR = 17; + constexpr uint8_t XOFF_CHAR = 19; + uint8_t xon_xoff_state = XON_XOFF_CHAR_SENT | XON_CHAR; + + // Validate that RX buffer size is at least 4096 bytes- According to several experiments, on + // the original Arduino Due that uses a ATmega16U2 as USB to serial bridge, due to the introduced + // latencies, at least 2959 bytes of RX buffering (when transmitting at 250kbits/s) are required + // to avoid overflows. + + #if RX_BUFFER_SIZE < 4096 + #error Arduino DUE requires at least 4096 bytes of RX buffer to avoid buffer overflows when using XON/XOFF handshake + #endif +#endif + +#if ENABLED(SERIAL_STATS_DROPPED_RX) + uint8_t rx_dropped_bytes = 0; +#endif + +#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) + ring_buffer_pos_t rx_max_enqueued = 0; +#endif + +// A SW memory barrier, to ensure GCC does not overoptimize loops +#define sw_barrier() asm volatile("": : :"memory"); + +#if ENABLED(EMERGENCY_PARSER) + + #include "../../module/stepper.h" + + // Currently looking for: M108, M112, M410 + // If you alter the parser please don't forget to update the capabilities in Conditionals_post.h + + FORCE_INLINE void emergency_parser(const uint8_t c) { + + static e_parser_state state = state_RESET; + + switch (state) { + case state_RESET: + switch (c) { + case ' ': break; + case 'N': state = state_N; break; + case 'M': state = state_M; break; + default: state = state_IGNORE; + } + break; + + case state_N: + switch (c) { + case '0': case '1': case '2': + case '3': case '4': case '5': + case '6': case '7': case '8': + case '9': case '-': case ' ': break; + case 'M': state = state_M; break; + default: state = state_IGNORE; + } + break; + + case state_M: + switch (c) { + case ' ': break; + case '1': state = state_M1; break; + case '4': state = state_M4; break; + default: state = state_IGNORE; + } + break; + + case state_M1: + switch (c) { + case '0': state = state_M10; break; + case '1': state = state_M11; break; + default: state = state_IGNORE; + } + break; + + case state_M10: + state = (c == '8') ? state_M108 : state_IGNORE; + break; + + case state_M11: + state = (c == '2') ? state_M112 : state_IGNORE; + break; + + case state_M4: + state = (c == '1') ? state_M41 : state_IGNORE; + break; + + case state_M41: + state = (c == '0') ? state_M410 : state_IGNORE; + break; + + case state_IGNORE: + if (c == '\n') state = state_RESET; + break; + + default: + if (c == '\n') { + switch (state) { + case state_M108: + wait_for_user = wait_for_heatup = false; + break; + case state_M112: + kill(PSTR(MSG_KILLED)); + break; + case state_M410: + quickstop_stepper(); + break; + default: + break; + } + state = state_RESET; + } + } + } + +#endif // EMERGENCY_PARSER + +FORCE_INLINE void store_rxd_char() { + + const ring_buffer_pos_t h = rx_buffer.head, + i = (ring_buffer_pos_t)(h + 1) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); + + // Read the character + const uint8_t c = HWUART->UART_RHR; + + // If the character is to be stored at the index just before the tail + // (such that the head would advance to the current tail), the buffer is + // critical, so don't write the character or advance the head. + if (i != rx_buffer.tail) { + rx_buffer.buffer[h] = c; + rx_buffer.head = i; + } + #if ENABLED(SERIAL_STATS_DROPPED_RX) + else if (!++rx_dropped_bytes) ++rx_dropped_bytes; + #endif + +#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) + // calculate count of bytes stored into the RX buffer + ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); + // Keep track of the maximum count of enqueued bytes + NOLESS(rx_max_enqueued, rx_count); +#endif + +#if ENABLED(SERIAL_XON_XOFF) + + // for high speed transfers, we can use XON/XOFF protocol to do + // software handshake and avoid overruns. + if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XON_CHAR) { + + // calculate count of bytes stored into the RX buffer + ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); + + // if we are above 12.5% of RX buffer capacity, send XOFF before + // we run out of RX buffer space .. We need 325 bytes @ 250kbits/s to + // let the host react and stop sending bytes. This translates to 13mS + // propagation time. + if (rx_count >= (RX_BUFFER_SIZE) / 8) { + // If TX interrupts are disabled and data register is empty, + // just write the byte to the data register and be done. This + // shortcut helps significantly improve the effective datarate + // at high (>500kbit/s) bitrates, where interrupt overhead + // becomes a slowdown. + if (!(HWUART->UART_IMR & UART_IMR_TXRDY) && (HWUART->UART_SR & UART_SR_TXRDY)) { + // Send an XOFF character + HWUART->UART_THR = XOFF_CHAR; + + // And remember it was sent + xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT; + } + else { + // TX interrupts disabled, but buffer still not empty ... or + // TX interrupts enabled. Reenable TX ints and schedule XOFF + // character to be sent + #if TX_BUFFER_SIZE > 0 + HWUART->UART_IER = UART_IER_TXRDY; + xon_xoff_state = XOFF_CHAR; + #else + // We are not using TX interrupts, we will have to send this manually + while (!(HWUART->UART_SR & UART_SR_TXRDY)) { sw_barrier(); }; + HWUART->UART_THR = XOFF_CHAR; + // And remember we already sent it + xon_xoff_state = XOFF_CHAR | XON_XOFF_CHAR_SENT; + #endif + } + } + } +#endif // SERIAL_XON_XOFF + +#if ENABLED(EMERGENCY_PARSER) + emergency_parser(c); +#endif +} + +#if TX_BUFFER_SIZE > 0 + + FORCE_INLINE void _tx_thr_empty_irq(void) { + // If interrupts are enabled, there must be more data in the output + // buffer. + + #if ENABLED(SERIAL_XON_XOFF) + // Do a priority insertion of an XON/XOFF char, if needed. + const uint8_t state = xon_xoff_state; + if (!(state & XON_XOFF_CHAR_SENT)) { + HWUART->UART_THR = state & XON_XOFF_CHAR_MASK; + xon_xoff_state = state | XON_XOFF_CHAR_SENT; + } + else + #endif + { // Send the next byte + const uint8_t t = tx_buffer.tail, c = tx_buffer.buffer[t]; + tx_buffer.tail = (t + 1) & (TX_BUFFER_SIZE - 1); + HWUART->UART_THR = c; + } + + // Disable interrupts if the buffer is empty + if (tx_buffer.head == tx_buffer.tail) + HWUART->UART_IDR = UART_IDR_TXRDY; + } + +#endif // TX_BUFFER_SIZE + +static void UART_ISR(void) { + uint32_t status = HWUART->UART_SR; + + // Did we receive data? + if (status & UART_SR_RXRDY) + store_rxd_char(); + + #if TX_BUFFER_SIZE > 0 + // Do we have something to send, and TX interrupts are enabled (meaning something to send) ? + if ((status & UART_SR_TXRDY) && (HWUART->UART_IMR & UART_IMR_TXRDY)) + _tx_thr_empty_irq(); + #endif + + // Acknowledge errors + if ((status & UART_SR_OVRE) || (status & UART_SR_FRAME)) { + // TODO: error reporting outside ISR + HWUART->UART_CR = UART_CR_RSTSTA; + } +} + +// Public Methods + +void MarlinSerial::begin(const long baud_setting) { + + // Disable UART interrupt in NVIC + NVIC_DisableIRQ( HWUART_IRQ ); + + // Disable clock + pmc_disable_periph_clk( HWUART_IRQ_ID ); + + // Configure PMC + pmc_enable_periph_clk( HWUART_IRQ_ID ); + + // Disable PDC channel + HWUART->UART_PTCR = UART_PTCR_RXTDIS | UART_PTCR_TXTDIS; + + // Reset and disable receiver and transmitter + HWUART->UART_CR = UART_CR_RSTRX | UART_CR_RSTTX | UART_CR_RXDIS | UART_CR_TXDIS; + + // Configure mode: 8bit, No parity, 1 bit stop + HWUART->UART_MR = UART_MR_CHMODE_NORMAL | US_MR_CHRL_8_BIT | US_MR_NBSTOP_1_BIT | UART_MR_PAR_NO; + + // Configure baudrate (asynchronous, no oversampling) + HWUART->UART_BRGR = (SystemCoreClock / (baud_setting << 4)); + + // Configure interrupts + HWUART->UART_IDR = 0xFFFFFFFF; + HWUART->UART_IER = UART_IER_RXRDY | UART_IER_OVRE | UART_IER_FRAME; + + // Install interrupt handler + install_isr(HWUART_IRQ, UART_ISR); + + // Enable UART interrupt in NVIC + NVIC_EnableIRQ(HWUART_IRQ); + + // Enable receiver and transmitter + HWUART->UART_CR = UART_CR_RXEN | UART_CR_TXEN; + + #if TX_BUFFER_SIZE > 0 + _written = false; + #endif +} + +void MarlinSerial::end() { + // Disable UART interrupt in NVIC + NVIC_DisableIRQ( HWUART_IRQ ); + + pmc_disable_periph_clk( HWUART_IRQ_ID ); +} + +void MarlinSerial::checkRx(void) { + if (HWUART->UART_SR & UART_SR_RXRDY) { + CRITICAL_SECTION_START; + store_rxd_char(); + CRITICAL_SECTION_END; + } +} + +int MarlinSerial::peek(void) { + CRITICAL_SECTION_START; + const int v = rx_buffer.head == rx_buffer.tail ? -1 : rx_buffer.buffer[rx_buffer.tail]; + CRITICAL_SECTION_END; + return v; +} + +int MarlinSerial::read(void) { + int v; + CRITICAL_SECTION_START; + const ring_buffer_pos_t t = rx_buffer.tail; + if (rx_buffer.head == t) + v = -1; + else { + v = rx_buffer.buffer[t]; + rx_buffer.tail = (ring_buffer_pos_t)(t + 1) & (RX_BUFFER_SIZE - 1); + + #if ENABLED(SERIAL_XON_XOFF) + if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) { + // Get count of bytes in the RX buffer + ring_buffer_pos_t rx_count = (ring_buffer_pos_t)(rx_buffer.head - rx_buffer.tail) & (ring_buffer_pos_t)(RX_BUFFER_SIZE - 1); + // When below 10% of RX buffer capacity, send XON before + // running out of RX buffer bytes + if (rx_count < (RX_BUFFER_SIZE) / 10) { + xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT; + CRITICAL_SECTION_END; // End critical section before returning! + writeNoHandshake(XON_CHAR); + return v; + } + } + #endif + } + CRITICAL_SECTION_END; + return v; +} + +ring_buffer_pos_t MarlinSerial::available(void) { + CRITICAL_SECTION_START; + const ring_buffer_pos_t h = rx_buffer.head, t = rx_buffer.tail; + CRITICAL_SECTION_END; + return (ring_buffer_pos_t)(RX_BUFFER_SIZE + h - t) & (RX_BUFFER_SIZE - 1); +} + +void MarlinSerial::flush(void) { + // Don't change this order of operations. If the RX interrupt occurs between + // reading rx_buffer_head and updating rx_buffer_tail, the previous rx_buffer_head + // may be written to rx_buffer_tail, making the buffer appear full rather than empty. + CRITICAL_SECTION_START; + rx_buffer.head = rx_buffer.tail; + CRITICAL_SECTION_END; + +#if ENABLED(SERIAL_XON_XOFF) + if ((xon_xoff_state & XON_XOFF_CHAR_MASK) == XOFF_CHAR) { + xon_xoff_state = XON_CHAR | XON_XOFF_CHAR_SENT; + writeNoHandshake(XON_CHAR); + } +#endif +} + +#if TX_BUFFER_SIZE > 0 + uint8_t MarlinSerial::availableForWrite(void) { + CRITICAL_SECTION_START; + const uint8_t h = tx_buffer.head, t = tx_buffer.tail; + CRITICAL_SECTION_END; + return (uint8_t)(TX_BUFFER_SIZE + h - t) & (TX_BUFFER_SIZE - 1); + } + + void MarlinSerial::write(const uint8_t c) { + #if ENABLED(SERIAL_XON_XOFF) + const uint8_t state = xon_xoff_state; + if (!(state & XON_XOFF_CHAR_SENT)) { + // Send 2 chars: XON/XOFF, then a user-specified char + writeNoHandshake(state & XON_XOFF_CHAR_MASK); + xon_xoff_state = state | XON_XOFF_CHAR_SENT; + } + #endif + writeNoHandshake(c); + } + + void MarlinSerial::writeNoHandshake(const uint8_t c) { + _written = true; + CRITICAL_SECTION_START; + bool emty = (tx_buffer.head == tx_buffer.tail); + CRITICAL_SECTION_END; + // If the buffer and the data register is empty, just write the byte + // to the data register and be done. This shortcut helps + // significantly improve the effective datarate at high (> + // 500kbit/s) bitrates, where interrupt overhead becomes a slowdown. + if (emty && (HWUART->UART_SR & UART_SR_TXRDY)) { + CRITICAL_SECTION_START; + HWUART->UART_THR = c; + HWUART->UART_IER = UART_IER_TXRDY; + CRITICAL_SECTION_END; + return; + } + const uint8_t i = (tx_buffer.head + 1) & (TX_BUFFER_SIZE - 1); + + // If the output buffer is full, there's nothing for it other than to + // wait for the interrupt handler to empty it a bit + while (i == tx_buffer.tail) { + if (__get_PRIMASK()) { + // Interrupts are disabled, so we'll have to poll the data + // register empty flag ourselves. If it is set, pretend an + // interrupt has happened and call the handler to free up + // space for us. + if (HWUART->UART_SR & UART_SR_TXRDY) + _tx_thr_empty_irq(); + } + else { + // nop, the interrupt handler will free up space for us + } + sw_barrier(); + } + + tx_buffer.buffer[tx_buffer.head] = c; + { CRITICAL_SECTION_START; + tx_buffer.head = i; + HWUART->UART_IER = UART_IER_TXRDY; + CRITICAL_SECTION_END; + } + return; + } + + void MarlinSerial::flushTX(void) { + // TX + // If we have never written a byte, no need to flush. + if (!_written) + return; + + while ((HWUART->UART_IMR & UART_IMR_TXRDY) || !(HWUART->UART_SR & UART_SR_TXEMPTY)) { + if (__get_PRIMASK()) + if ((HWUART->UART_SR & UART_SR_TXRDY)) + _tx_thr_empty_irq(); + sw_barrier(); + } + // If we get here, nothing is queued anymore (TX interrupts are disabled) and + // the hardware finished tranmission (TXEMPTY is set). + } + +#else // TX_BUFFER_SIZE == 0 + + void MarlinSerial::write(const uint8_t c) { + #if ENABLED(SERIAL_XON_XOFF) + // Do a priority insertion of an XON/XOFF char, if needed. + const uint8_t state = xon_xoff_state; + if (!(state & XON_XOFF_CHAR_SENT)) { + writeNoHandshake(state & XON_XOFF_CHAR_MASK); + xon_xoff_state = state | XON_XOFF_CHAR_SENT; + } + #endif + writeNoHandshake(c); + } + + void MarlinSerial::writeNoHandshake(const uint8_t c) { + while (!(HWUART->UART_SR & UART_SR_TXRDY)) { sw_barrier(); }; + HWUART->UART_THR = c; + } + +#endif // TX_BUFFER_SIZE == 0 + +/** +* Imports from print.h +*/ + +void MarlinSerial::print(char c, int base) { + print((long)c, base); +} + +void MarlinSerial::print(unsigned char b, int base) { + print((unsigned long)b, base); +} + +void MarlinSerial::print(int n, int base) { + print((long)n, base); +} + +void MarlinSerial::print(unsigned int n, int base) { + print((unsigned long)n, base); +} + +void MarlinSerial::print(long n, int base) { + if (base == 0) + write(n); + else if (base == 10) { + if (n < 0) { + print('-'); + n = -n; + } + printNumber(n, 10); + } + else + printNumber(n, base); +} + +void MarlinSerial::print(unsigned long n, int base) { + if (base == 0) write(n); + else printNumber(n, base); +} + +void MarlinSerial::print(double n, int digits) { + printFloat(n, digits); +} + +void MarlinSerial::println(void) { + print('\r'); + print('\n'); +} + +void MarlinSerial::println(const String& s) { + print(s); + println(); +} + +void MarlinSerial::println(const char c[]) { + print(c); + println(); +} + +void MarlinSerial::println(char c, int base) { + print(c, base); + println(); +} + +void MarlinSerial::println(unsigned char b, int base) { + print(b, base); + println(); +} + +void MarlinSerial::println(int n, int base) { + print(n, base); + println(); +} + +void MarlinSerial::println(unsigned int n, int base) { + print(n, base); + println(); +} + +void MarlinSerial::println(long n, int base) { + print(n, base); + println(); +} + +void MarlinSerial::println(unsigned long n, int base) { + print(n, base); + println(); +} + +void MarlinSerial::println(double n, int digits) { + print(n, digits); + println(); +} + +// Private Methods + +void MarlinSerial::printNumber(unsigned long n, uint8_t base) { + if (n) { + unsigned char buf[8 * sizeof(long)]; // Enough space for base 2 + int8_t i = 0; + while (n) { + buf[i++] = n % base; + n /= base; + } + while (i--) + print((char)(buf[i] + (buf[i] < 10 ? '0' : 'A' - 10))); + } + else + print('0'); +} + +void MarlinSerial::printFloat(double number, uint8_t digits) { + // Handle negative numbers + if (number < 0.0) { + print('-'); + number = -number; + } + + // Round correctly so that print(1.999, 2) prints as "2.00" + double rounding = 0.5; + for (uint8_t i = 0; i < digits; ++i) + rounding *= 0.1; + + number += rounding; + + // Extract the integer part of the number and print it + unsigned long int_part = (unsigned long)number; + double remainder = number - (double)int_part; + print(int_part); + + // Print the decimal point, but only if there are digits beyond + if (digits) { + print('.'); + // Extract digits from the remainder one at a time + while (digits--) { + remainder *= 10.0; + int toPrint = int(remainder); + print(toPrint); + remainder -= toPrint; + } + } +} + +// Preinstantiate +MarlinSerial customizedSerial; + +#endif // ARDUINO_ARCH_SAM diff --git a/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.h b/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.h new file mode 100644 index 000000000..740db4d9c --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/MarlinSerial_Due.h @@ -0,0 +1,142 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * MarlinSerial_Due.h - Hardware serial library for Arduino DUE + * Copyright (c) 2017 Eduardo José Tagle. All right reserved + * Based on MarlinSerial for AVR, copyright (c) 2006 Nicholas Zambetti. All right reserved. + */ + +#ifndef MARLINSERIAL_DUE_H +#define MARLINSERIAL_DUE_H + +#include "../../inc/MarlinConfig.h" + +#include + +#ifndef SERIAL_PORT + #define SERIAL_PORT 0 +#endif + +#define DEC 10 +#define HEX 16 +#define OCT 8 +#define BIN 2 +#define BYTE 0 + +// Define constants and variables for buffering incoming serial data. We're +// using a ring buffer (I think), in which rx_buffer_head is the index of the +// location to which to write the next incoming character and rx_buffer_tail +// is the index of the location from which to read. +// 256 is the max limit due to uint8_t head and tail. Use only powers of 2. (...,16,32,64,128,256) +#ifndef RX_BUFFER_SIZE + #define RX_BUFFER_SIZE 128 +#endif +#ifndef TX_BUFFER_SIZE + #define TX_BUFFER_SIZE 32 +#endif + +#if ENABLED(SERIAL_XON_XOFF) && RX_BUFFER_SIZE < 1024 + #error "XON/XOFF requires RX_BUFFER_SIZE >= 1024 for reliable transfers without drops." +#endif + +#if !IS_POWER_OF_2(RX_BUFFER_SIZE) || RX_BUFFER_SIZE < 2 + #error "RX_BUFFER_SIZE must be a power of 2 greater than 1." +#endif + +#if TX_BUFFER_SIZE && (TX_BUFFER_SIZE < 2 || TX_BUFFER_SIZE > 256 || !IS_POWER_OF_2(TX_BUFFER_SIZE)) + #error "TX_BUFFER_SIZE must be 0 or a power of 2 greater than 1." +#endif + +#if RX_BUFFER_SIZE > 256 + typedef uint16_t ring_buffer_pos_t; +#else + typedef uint8_t ring_buffer_pos_t; +#endif + +#if ENABLED(SERIAL_STATS_DROPPED_RX) + extern uint8_t rx_dropped_bytes; +#endif + +#if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) + extern ring_buffer_pos_t rx_max_enqueued; +#endif + +class MarlinSerial { + +public: + MarlinSerial() {}; + static void begin(const long); + static void end(); + static int peek(void); + static int read(void); + static void flush(void); + static ring_buffer_pos_t available(void); + static void checkRx(void); + static void write(const uint8_t c); + #if TX_BUFFER_SIZE > 0 + static uint8_t availableForWrite(void); + static void flushTX(void); + #endif + static void writeNoHandshake(const uint8_t c); + + #if ENABLED(SERIAL_STATS_DROPPED_RX) + FORCE_INLINE static uint32_t dropped() { return rx_dropped_bytes; } + #endif + + #if ENABLED(SERIAL_STATS_MAX_RX_QUEUED) + FORCE_INLINE static ring_buffer_pos_t rxMaxEnqueued() { return rx_max_enqueued; } + #endif + + static FORCE_INLINE void write(const char* str) { while (*str) write(*str++); } + static FORCE_INLINE void write(const uint8_t* buffer, size_t size) { while (size--) write(*buffer++); } + static FORCE_INLINE void print(const String& s) { for (int i = 0; i < (int)s.length(); i++) write(s[i]); } + static FORCE_INLINE void print(const char* str) { write(str); } + + static void print(char, int = BYTE); + static void print(unsigned char, int = BYTE); + static void print(int, int = DEC); + static void print(unsigned int, int = DEC); + static void print(long, int = DEC); + static void print(unsigned long, int = DEC); + static void print(double, int = 2); + + static void println(const String& s); + static void println(const char[]); + static void println(char, int = BYTE); + static void println(unsigned char, int = BYTE); + static void println(int, int = DEC); + static void println(unsigned int, int = DEC); + static void println(long, int = DEC); + static void println(unsigned long, int = DEC); + static void println(double, int = 2); + static void println(void); + operator bool() { return true; } + +private: + static void printNumber(unsigned long, const uint8_t); + static void printFloat(double, uint8_t); +}; + +extern MarlinSerial customizedSerial; + +#endif // MARLINSERIAL_DUE_H diff --git a/Marlin/src/core/serial.h b/Marlin/src/core/serial.h index 07d3ac173..887402a06 100644 --- a/Marlin/src/core/serial.h +++ b/Marlin/src/core/serial.h @@ -25,24 +25,10 @@ #include "../inc/MarlinConfig.h" -//todo: HAL: breaks encapsulation -// For AVR only, define a serial interface based on configuration -#ifdef __AVR__ - #ifdef USBCON - #include "HardwareSerial.h" - #if ENABLED(BLUETOOTH) - #define MYSERIAL bluetoothSerial - #else - #define MYSERIAL Serial - #endif // BLUETOOTH - #else - #include "../HAL/HAL_AVR/MarlinSerial.h" - #define MYSERIAL customizedSerial - #endif +#if HAS_ABL && ENABLED(DEBUG_LEVELING_FEATURE) + #include "../libs/vector_3.h" #endif -#include "../libs/vector_3.h" - /** * Define debug bit-masks */ @@ -58,6 +44,27 @@ enum DebugFlags { DEBUG_ALL = 0xFF }; +//todo: HAL: breaks encapsulation +// For AVR only, define a serial interface based on configuration +#ifdef __AVR__ + #ifdef USBCON + #include "HardwareSerial.h" + #if ENABLED(BLUETOOTH) + #define MYSERIAL bluetoothSerial + #else + #define MYSERIAL Serial + #endif // BLUETOOTH + #else + #include "../HAL/HAL_AVR/MarlinSerial.h" + #define MYSERIAL customizedSerial + #endif +#endif + +#ifdef ARDUINO_ARCH_SAM + // To pull the Serial port definitions and overrides + #include "../HAL/HAL_DUE/MarlinSerial_Due.h" +#endif + extern uint8_t marlin_debug_flags; #define DEBUGGING(F) (marlin_debug_flags & (DEBUG_## F))