From a9acd2f4973cbbff1b936229ff97a3b56e4157ff Mon Sep 17 00:00:00 2001 From: InsanityAutomation <38436470+InsanityAutomation@users.noreply.github.com> Date: Thu, 20 Jun 2019 22:18:36 -0400 Subject: [PATCH] G34 configurable angle limit (#14321) --- Marlin/Configuration_adv.h | 4 ++++ Marlin/src/gcode/calibrate/G34_M422.cpp | 7 ++----- config/default/Configuration_adv.h | 4 ++++ config/examples/3DFabXYZ/Migbot/Configuration_adv.h | 4 ++++ config/examples/AlephObjects/TAZ4/Configuration_adv.h | 4 ++++ config/examples/AliExpress/UM2pExt/Configuration_adv.h | 4 ++++ config/examples/Anet/A2/Configuration_adv.h | 4 ++++ config/examples/Anet/A2plus/Configuration_adv.h | 4 ++++ config/examples/Anet/A6/Configuration_adv.h | 4 ++++ config/examples/Anet/A8/Configuration_adv.h | 4 ++++ config/examples/Anet/A8plus/Configuration_adv.h | 4 ++++ config/examples/Anet/E16/Configuration_adv.h | 4 ++++ config/examples/AnyCubic/i3/Configuration_adv.h | 4 ++++ config/examples/ArmEd/Configuration_adv.h | 4 ++++ config/examples/BIBO/TouchX/cyclops/Configuration_adv.h | 4 ++++ config/examples/BIBO/TouchX/default/Configuration_adv.h | 4 ++++ config/examples/BQ/Hephestos/Configuration_adv.h | 4 ++++ config/examples/BQ/Hephestos_2/Configuration_adv.h | 4 ++++ config/examples/BQ/WITBOX/Configuration_adv.h | 4 ++++ config/examples/Cartesio/Configuration_adv.h | 4 ++++ config/examples/Creality/CR-10/Configuration_adv.h | 4 ++++ config/examples/Creality/CR-10S/Configuration_adv.h | 4 ++++ config/examples/Creality/CR-10_5S/Configuration_adv.h | 4 ++++ config/examples/Creality/CR-10mini/Configuration_adv.h | 4 ++++ config/examples/Creality/CR-8/Configuration_adv.h | 4 ++++ config/examples/Creality/Ender-2/Configuration_adv.h | 4 ++++ config/examples/Creality/Ender-3/Configuration_adv.h | 4 ++++ config/examples/Creality/Ender-4/Configuration_adv.h | 4 ++++ config/examples/Dagoma/Disco Ultimate/Configuration_adv.h | 4 ++++ .../EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h | 4 ++++ config/examples/Einstart-S/Configuration_adv.h | 4 ++++ config/examples/Felix/Configuration_adv.h | 4 ++++ config/examples/FlashForge/CreatorPro/Configuration_adv.h | 4 ++++ config/examples/FolgerTech/i3-2020/Configuration_adv.h | 4 ++++ config/examples/Formbot/Raptor/Configuration_adv.h | 4 ++++ config/examples/Formbot/T_Rex_2+/Configuration_adv.h | 4 ++++ config/examples/Formbot/T_Rex_3/Configuration_adv.h | 4 ++++ config/examples/Geeetech/A10/Configuration_adv.h | 4 ++++ config/examples/Geeetech/A10M/Configuration_adv.h | 4 ++++ config/examples/Geeetech/A20M/Configuration_adv.h | 4 ++++ config/examples/Geeetech/MeCreator2/Configuration_adv.h | 4 ++++ .../examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h | 4 ++++ .../examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h | 4 ++++ config/examples/Infitary/i3-M508/Configuration_adv.h | 4 ++++ config/examples/JGAurora/A1/Configuration_adv.h | 4 ++++ config/examples/JGAurora/A5/Configuration_adv.h | 4 ++++ config/examples/JGAurora/A5S/Configuration_adv.h | 4 ++++ config/examples/MakerParts/Configuration_adv.h | 4 ++++ config/examples/Malyan/M150/Configuration_adv.h | 4 ++++ config/examples/Malyan/M200/Configuration_adv.h | 4 ++++ config/examples/Micromake/C1/enhanced/Configuration_adv.h | 4 ++++ config/examples/Mks/Robin/Configuration_adv.h | 4 ++++ config/examples/Mks/Sbase/Configuration_adv.h | 4 ++++ config/examples/RapideLite/RL200/Configuration_adv.h | 4 ++++ config/examples/RigidBot/Configuration_adv.h | 4 ++++ config/examples/SCARA/Configuration_adv.h | 4 ++++ .../examples/STM32/Black_STM32F407VET6/Configuration_adv.h | 4 ++++ config/examples/Sanguinololu/Configuration_adv.h | 4 ++++ config/examples/TheBorg/Configuration_adv.h | 4 ++++ config/examples/TinyBoy2/Configuration_adv.h | 4 ++++ config/examples/Tronxy/X3A/Configuration_adv.h | 4 ++++ config/examples/Tronxy/X5S-2E/Configuration_adv.h | 4 ++++ config/examples/UltiMachine/Archim1/Configuration_adv.h | 4 ++++ config/examples/UltiMachine/Archim2/Configuration_adv.h | 4 ++++ config/examples/VORONDesign/Configuration_adv.h | 4 ++++ config/examples/Velleman/K8200/Configuration_adv.h | 4 ++++ config/examples/Velleman/K8400/Configuration_adv.h | 4 ++++ config/examples/WASP/PowerWASP/Configuration_adv.h | 4 ++++ config/examples/Wanhao/Duplicator 6/Configuration_adv.h | 4 ++++ config/examples/delta/Anycubic/Kossel/Configuration_adv.h | 4 ++++ .../delta/FLSUN/auto_calibrate/Configuration_adv.h | 4 ++++ config/examples/delta/FLSUN/kossel/Configuration_adv.h | 4 ++++ .../examples/delta/FLSUN/kossel_mini/Configuration_adv.h | 4 ++++ .../delta/Geeetech/Rostock 301/Configuration_adv.h | 4 ++++ config/examples/delta/MKS/SBASE/Configuration_adv.h | 4 ++++ .../examples/delta/Tevo Little Monster/Configuration_adv.h | 4 ++++ config/examples/delta/generic/Configuration_adv.h | 4 ++++ config/examples/delta/kossel_mini/Configuration_adv.h | 4 ++++ config/examples/delta/kossel_xl/Configuration_adv.h | 4 ++++ config/examples/gCreate/gMax1.5+/Configuration_adv.h | 4 ++++ config/examples/makibox/Configuration_adv.h | 4 ++++ config/examples/tvrrug/Round2/Configuration_adv.h | 4 ++++ config/examples/wt150/Configuration_adv.h | 4 ++++ 83 files changed, 330 insertions(+), 5 deletions(-) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 1ea73f5a9..76ea4b10d 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/Marlin/src/gcode/calibrate/G34_M422.cpp b/Marlin/src/gcode/calibrate/G34_M422.cpp index 1067a06bf..7fb1476b5 100644 --- a/Marlin/src/gcode/calibrate/G34_M422.cpp +++ b/Marlin/src/gcode/calibrate/G34_M422.cpp @@ -125,10 +125,7 @@ void GcodeSuite::G34() { #define Z_BASIC_CLEARANCE Z_CLEARANCE_BETWEEN_PROBES #endif - // 0.05 is a 5% incline. On a 300mm bed that would be a misalignment of about 1.5cm. - // This angle is the maximum misalignment catered for - #define MAX_ANGLE 0.05f - float z_probe = Z_BASIC_CLEARANCE + MAX_ANGLE * ( + float z_probe = Z_BASIC_CLEARANCE + (G34_MAX_GRADE) * 0.01f * ( #if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) SQRT(MAX(HYPOT2(z_auto_align_xpos[0] - z_auto_align_ypos[0], z_auto_align_xpos[1] - z_auto_align_ypos[1]), HYPOT2(z_auto_align_xpos[1] - z_auto_align_ypos[1], z_auto_align_xpos[2] - z_auto_align_ypos[2]), @@ -160,7 +157,7 @@ void GcodeSuite::G34() { float z_measured_min = 100000.0f; // Probe all positions (one per Z-Stepper) for (uint8_t izstepper = 0; izstepper < Z_STEPPER_COUNT; ++izstepper) { - // iteration odd/even --> downward / upward stepper sequence + // iteration odd/even --> downward / upward stepper sequence const uint8_t zstepper = (iteration & 1) ? Z_STEPPER_COUNT - 1 - izstepper : izstepper; // Safe clearance even on an incline diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 0193e91dc..30eda71e7 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index 28a3c6655..2e8398bea 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 3dbac67d9..5fb0910b4 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index eaff5f093..7d123b873 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 3a4e964f9..db40e1b6e 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 3a4e964f9..db40e1b6e 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index bf5fd0cc1..55130fb5f 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index d8b79d69a..a809f16e3 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 0aaf77a91..656ff95c3 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 1bf5a738a..96c3c3f04 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index b064d69e1..850666d9c 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index a21ff261c..3b3c37dac 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -608,6 +608,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 99530eb51..d5a7265e3 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 2e1d77474..935e3ae63 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 799a4edea..685d311fb 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index c13d6a8bb..0b4f42bf8 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index 799a4edea..685d311fb 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index b97f41e5a..c403c4ea7 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 1c836540c..d2596a64e 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index c4beb0302..36ca31fb7 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 1dc0752d5..859401c1d 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index 64cbdfc96..202acc2c3 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index e8791319b..de25e8235 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 5816142cd..31119dcd1 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 2998499e2..c016c6b05 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index caa542f90..796d3995d 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index 4a251eab6..173958c1d 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h index 366446388..507e1615d 100755 --- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h +++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 614b02485..f21896adf 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h index 06fbb9067..680271070 100644 --- a/config/examples/Felix/Configuration_adv.h +++ b/config/examples/Felix/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 5fbc12ca7..1ef988859 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index cdeee0535..4991c59ed 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index e948c56ec..6971b95e5 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index b55b1901b..05386ef91 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -608,6 +608,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index c979067f8..0f971699a 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -608,6 +608,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index 8cb0fd8fc..e93d31991 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 3b78afc88..4bb7b303d 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 1a390da50..755f6a0af 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index b20633c93..892760246 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index 8cb0fd8fc..e93d31991 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index 8cb0fd8fc..e93d31991 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 2527dd201..b16f5b2f2 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index b21ce2a9a..152dd52c5 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -609,6 +609,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index 26d655de4..b4a0888cc 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index b21ce2a9a..152dd52c5 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -609,6 +609,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 3b34d330e..7ad8e46be 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 143a78dda..441d1d457 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 60c1607c3..bbd3b0821 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index bc055ce4a..b0db73b35 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 916c33cf3..e7bb976b3 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 8d8909b0f..ef261b04a 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 219f331f2..ca0ed99d9 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index 5626f0dca..9df5bf6fc 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h index ca9d4df7b..ec2908731 100644 --- a/config/examples/SCARA/Configuration_adv.h +++ b/config/examples/SCARA/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index bd43f5511..70c11771e 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index dad8a2d4f..b829546e7 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 67ffb6c17..a227aa844 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index cc9650f71..f78dda06f 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index b8238fbb3..9803e09f6 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index d0b0c2419..6b82018e8 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index e231ec0ba..9895c9152 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index 750a67154..f3de4fa3e 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 85cace09a..4d41ead46 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 0c377caab..3e4d1c823 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -617,6 +617,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h index 31496464f..ca4a596a5 100644 --- a/config/examples/Velleman/K8400/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index d7add26aa..1e592a730 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index aff6c351a..39fbeea02 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 0c10f6afd..e83f4f034 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 2677c6a51..b2e12c13c 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 2677c6a51..b2e12c13c 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 3d87856fd..c585af13b 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index 3d87856fd..c585af13b 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 9363707ad..6e8b5bb83 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 0569eeacf..22a0988d2 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 3d87856fd..c585af13b 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 3d87856fd..c585af13b 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index bccb86360..e4c837035 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 3883618fb..0613e94b4 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index 8f1cecb31..88cd7e510 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 459193865..8e8ad195d 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index 180472292..25d682b2e 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -604,6 +604,10 @@ #define Z_STEPPER_ALIGN_ITERATIONS 3 // Enable to restore leveling setup after operation #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + // Use the amplification factor to de-/increase correction step. // In case the stepper (spindle) position is further out than the test point // Use a value > 1. NOTE: This may cause instability