diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/pins_RAMPS_RE_ARM.h index 991e0c12d..0d8637210 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/pins_RAMPS_RE_ARM.h @@ -34,6 +34,8 @@ * */ +// numbers in parenthesis () are the mega2560 equivalent pin numbers + #ifndef TARGET_LPC1768 #error "Oops! Make sure you have LPC1768 selected." #endif @@ -47,60 +49,60 @@ // // Servos // -#define SERVO0_PIN P1_20 -#define SERVO1_PIN P1_21 // also on J5-1 -#define SERVO2_PIN P1_19 -#define SERVO3_PIN P1_18 // 5V output - PWM capable +#define SERVO0_PIN P1_20 // (11) +#define SERVO1_PIN P1_21 // ( 6) also on J5-1 +#define SERVO2_PIN P1_19 // ( 5) +#define SERVO3_PIN P1_18 // ( 4) 5V output - PWM capable // // Limit Switches // -#define X_MIN_PIN P1_24 //10k pullup to 3.3V, 1K series -#define X_MAX_PIN P1_25 //10k pullup to 3.3V, 1K series -#define Y_MIN_PIN P1_26 //10k pullup to 3.3V, 1K series -#define Y_MAX_PIN P1_27 //10k pullup to 3.3V, 1K series -#define Z_MIN_PIN P1_29 //10k pullup to 3.3V, 1K series -#define Z_MAX_PIN P1_28 //10k pullup to 3.3V, 1K series +#define X_MIN_PIN P1_24 // ( 3) 10k pullup to 3.3V, 1K series +#define X_MAX_PIN P1_25 // ( 2) 10k pullup to 3.3V, 1K series +#define Y_MIN_PIN P1_26 // (14) 10k pullup to 3.3V, 1K series +#define Y_MAX_PIN P1_27 // (15) 10k pullup to 3.3V, 1K series +#define Z_MIN_PIN P1_29 // (18) 10k pullup to 3.3V, 1K series +#define Z_MAX_PIN P1_28 // (19) 10k pullup to 3.3V, 1K series // // Steppers // -#define X_STEP_PIN P2_1 -#define X_DIR_PIN P0_11 -#define X_ENABLE_PIN P0_10 +#define X_STEP_PIN P2_1 // (54) +#define X_DIR_PIN P0_11 // (55) +#define X_ENABLE_PIN P0_10 // (38) -#define Y_STEP_PIN P2_2 -#define Y_DIR_PIN P0_20 -#define Y_ENABLE_PIN P0_19 +#define Y_STEP_PIN P2_2 // (60) +#define Y_DIR_PIN P0_20 // (61) +#define Y_ENABLE_PIN P0_19 // (56) -#define Z_STEP_PIN P2_3 -#define Z_DIR_PIN P0_22 -#define Z_ENABLE_PIN P0_21 +#define Z_STEP_PIN P2_3 // (46) +#define Z_DIR_PIN P0_22 // (48) +#define Z_ENABLE_PIN P0_21 // (62) -#define E0_STEP_PIN P2_0 -#define E0_DIR_PIN P0_5 -#define E0_ENABLE_PIN P0_4 +#define E0_STEP_PIN P2_0 // (26) +#define E0_DIR_PIN P0_5 // (28) +#define E0_ENABLE_PIN P0_4 // (24) -#define E1_STEP_PIN P2_8 -#define E1_DIR_PIN P2_13 -#define E1_ENABLE_PIN P4_29 +#define E1_STEP_PIN P2_8 // (36) +#define E1_DIR_PIN P2_13 // (34) +#define E1_ENABLE_PIN P4_29 // (30) -#define E2_STEP_PIN P2_8 -#define E2_DIR_PIN P2_13 -#define E2_ENABLE_PIN P4_29 +#define E2_STEP_PIN P2_8 // (36) +#define E2_DIR_PIN P2_13 // (34) +#define E2_ENABLE_PIN P4_29 // (30) // // Temperature Sensors // 3.3V max when defined as an analog input // -#define TEMP_0_PIN 0 //A0 (T0) - D67 - TEMP_0_PIN -#define TEMP_BED_PIN 1 //A1 (T1) - D68 - TEMP_BED_PIN -#define TEMP_1_PIN 2 //A2 (T2) - D69 - TEMP_1_PIN -#define TEMP_2_PIN 3 //A3 - D63 - J5-3 & AUX-2 -#define TEMP_3_PIN 4 //A4 - D37 - BUZZER_PIN -//#define TEMP_4_PIN 5 //A5 - D49 - SD_DETECT_PIN -//#define ?? 6 //A6 - D0 - RXD0 - J4-4 & AUX-1 -#define FILWIDTH_PIN 7 //A7 - D1 - TXD0 - J4-5 & AUX-1 +#define TEMP_0_PIN 0 //A0 (T0) - (67) - TEMP_0_PIN +#define TEMP_BED_PIN 1 //A1 (T1) - (68) - TEMP_BED_PIN +#define TEMP_1_PIN 2 //A2 (T2) - (69) - TEMP_1_PIN +#define TEMP_2_PIN 3 //A3 - (63) - J5-3 & AUX-2 +#define TEMP_3_PIN 4 //A4 - (37) - BUZZER_PIN +//#define TEMP_4_PIN 5 //A5 - (49) - SD_DETECT_PIN +//#define ?? 6 //A6 - ( 0) - RXD0 - J4-4 & AUX-1 +#define FILWIDTH_PIN 7 //A7 - ( 1) - TXD0 - J4-5 & AUX-1 // @@ -127,13 +129,13 @@ #define MOSFET_D_PIN -1 #endif #ifndef RAMPS_D8_PIN - #define RAMPS_D8_PIN P2_7 + #define RAMPS_D8_PIN P2_7 // (8) #endif #ifndef RAMPS_D9_PIN - #define RAMPS_D9_PIN P2_4 + #define RAMPS_D9_PIN P2_4 // (9) #endif #ifndef RAMPS_D10_PIN - #define RAMPS_D10_PIN P2_5 + #define RAMPS_D10_PIN P2_5 // (10) #endif #define HEATER_0_PIN RAMPS_D10_PIN @@ -163,22 +165,22 @@ #endif #ifndef FAN_PIN - #define FAN_PIN P1_18 // IO pin. Buffer needed + #define FAN_PIN P1_18 // (4) IO pin. Buffer needed #endif // // Misc. Functions // -#define LED_PIN P4_28 +#define LED_PIN P4_28 // (13) -// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector -#define FIL_RUNOUT_PIN P1_18 +// define digital pin 4 for ther t filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector +#define FIL_RUNOUT_PIN P1_18 // (4) -#define PS_ON_PIN P2_12 +#define PS_ON_PIN P2_12 // (12) #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector - #define CASE_LIGHT_PIN P1_18 // MUST BE HARDWARE PWM + #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM #endif #endif @@ -190,17 +192,17 @@ #undef SERVO1 #undef SERVO2 #undef SERVO3 - #define SPINDLE_LASER_ENABLE_PIN P1_21 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN P1_18 // MUST BE HARDWARE PWM - #define SPINDLE_DIR_PIN P1_19 + #define SPINDLE_LASER_ENABLE_PIN P1_21 // (6) Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN P1_18 // (4) MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN P1_19 // (5) #endif #endif // // Průša i3 MK2 Multiplexer Support // -#define E_MUX0_PIN P0_3 // Z_CS_PIN -#define E_MUX1_PIN P0_2 // E0_CS_PIN -#define E_MUX2_PIN P0_26 // E1_CS_PIN +#define E_MUX0_PIN P0_3 // ( 0) Z_CS_PIN +#define E_MUX1_PIN P0_2 // ( 1) E0_CS_PIN +#define E_MUX2_PIN P0_26 // (63) E1_CS_PIN /** * LCD / Controller @@ -223,76 +225,76 @@ #if ENABLED(ULTRA_LCD) - #define BEEPER_PIN P1_30 // not 5V tolerant + #define BEEPER_PIN P1_30 // (37) not 5V tolerant - #define BTN_EN1 P3_26 // J3-2 & AUX-4 - #define BTN_EN2 P3_25 // J3-4 & AUX-4 - #define BTN_ENC P2_11 // J3-3 & AUX-4 + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 - #define SD_DETECT_PIN P1_31 // not 5V tolerant J3-1 & AUX-3 - #define KILL_PIN P1_22 // J5-4 & AUX-4 - #define LCD_PINS_RS P0_16 // J3-7 & AUX-4 - #define LCD_SDSS P0_16 // J3-7 & AUX-4 - #define LCD_BACKLIGHT_PIN P0_16 // J3-7 & AUX-4 - only used on DOGLCD controllers - #define LCD_PINS_ENABLE P0_18 // (MOSI) J3-10 & AUX-3 - #define LCD_PINS_D4 P0_15 // (SCK) J3-9 & AUX-3 + #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 + #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 + #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 + #define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers + #define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3 - #define DOGLCD_A0 P2_6 // J3-8 & AUX-2 - #define DOGLCD_CS P0_26 // J5-3 & AUX-2 + #define DOGLCD_A0 P2_6 // (59) J3-8 & AUX-2 + #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #ifdef ULTIPANEL - #define LCD_PINS_D5 P1_17 // ENET_MDIO - #define LCD_PINS_D6 P1_14 // ENET_RX_ER - #define LCD_PINS_D7 P1_10 // ENET_RXD1 + #define LCD_PINS_D5 P1_17 // (71) ENET_MDIO + #define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER + #define LCD_PINS_D7 P1_10 // (75) ENET_RXD1 #endif #if ENABLED(NEWPANEL) #if ENABLED(REPRAPWORLD_KEYPAD) - #define SHIFT_OUT P0_18 // (MOSI) J3-10 & AUX-3 - #define SHIFT_CLK P0_15 // (SCK) J3-9 & AUX-3 - #define SHIFT_LD P1_31 // not 5V tolerant J3-1 & AUX-3 + #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3 + #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3 + #define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #endif #else - //#define SHIFT_CLK P3_26 // J3-2 & AUX-4 - //#define SHIFT_LD P3_25 // J3-4 & AUX-4 - //#define SHIFT_OUT P2_11 // J3-3 & AUX-4 - //#define SHIFT_EN P1_22 // J5-4 & AUX-4 + //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 + //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 + //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 + //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 #endif #if ENABLED(VIKI2) || ENABLED(miniVIKI) // #define LCD_SCREEN_ROT_180 #undef BEEPER_PIN - #define BEEPER_PIN P1_30 // may change if cable changes + #define BEEPER_PIN P1_30 // (37) may change if cable changes - #define BTN_EN1 P3_26 // J3-2 & AUX-4 - #define BTN_EN2 P3_25 // J3-4 & AUX-4 - #define BTN_ENC P2_11 // J3-3 & AUX-4 + #define BTN_EN1 P3_26 // (31) J3-2 & AUX-4 + #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 + #define BTN_ENC P2_11 // (35) J3-3 & AUX-4 - #define SD_DETECT_PIN P1_31 // not 5V tolerant J3-1 & AUX-3 - #define KILL_PIN P1_22 // J5-4 & AUX-4 + #define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 + #define KILL_PIN P1_22 // (41) J5-4 & AUX-4 #undef DOGLCD_CS - #define DOGLCD_CS P0_16 - #undef LCD_BACKLIGHT_PIN //P0_16 // J3-7 & AUX-4 - only used on DOGLCD controllers - #undef LCD_PINS_ENABLE //P0_18 // (MOSI) J3-10 & AUX-3 - #undef LCD_PINS_D4 //P0_15 // (SCK) J3-9 & AUX-3 - - #undef LCD_PINS_D5 //P2_6 // J3-8 & AUX-2 - #define DOGLCD_A0 P2_6 // J3-8 & AUX-2 - #undef LCD_PINS_D6 //P0_26 // J5-3 & AUX-2 - #undef LCD_PINS_D7 //P1_21 // (SERVO1) J5-1 & SERVO connector + #define DOGLCD_CS P0_16 // (16) + #undef LCD_BACKLIGHT_PIN //P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers + #undef LCD_PINS_ENABLE //P0_18 // (51) (MOSI) J3-10 & AUX-3 + #undef LCD_PINS_D4 //P0_15 // (52) (SCK) J3-9 & AUX-3 + + #undef LCD_PINS_D5 //P2_6 // (59) J3-8 & AUX-2 + #define DOGLCD_A0 P2_6 // (59) J3-8 & AUX-2 + #undef LCD_PINS_D6 //P0_26 // (63) J5-3 & AUX-2 + #undef LCD_PINS_D7 //P1_21 // ( 6) (SERVO1) J5-1 & SERVO connector #define DOGLCD_SCK SCK_PIN #define DOGLCD_MOSI MOSI_PIN - #define STAT_LED_BLUE_PIN P0_26 // may change if cable changes - #define STAT_LED_RED_PIN P1_21 // may change if cable changes + #define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes + #define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes #endif - //#define MISO_PIN P0_17 // system defined J3-10 & AUX-3 - //#define MOSI_PIN P0_18 // system defined J3-10 & AUX-3 - //#define SCK_PIN P0_15 // system defined J3-9 & AUX-3 - //#define SS_PIN P1_23 // system defined J3-5 & AUX-3 - sometimes called SDSS + //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 + //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 + //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 + //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS #if ENABLED(MINIPANEL) // GLCD features @@ -309,17 +311,17 @@ // Ethernet pins // #ifndef ULTIPANEL - #define ENET_MDIO P1_17 // J12-4 - #define ENET_RX_ER P1_14 // J12-6 - #define ENET_RXD1 P1_10 // J12-8 + #define ENET_MDIO P1_17 // (71) J12-4 + #define ENET_RX_ER P1_14 // (73) J12-6 + #define ENET_RXD1 P1_10 // (75) J12-8 #endif -#define ENET_MOC P1_16 // J12-3 -#define REF_CLK P1_15 // J12-5 -#define ENET_RXD0 P1_9 // J12-7 -#define ENET_CRS P1_8 // J12-9 -#define ENET_TX_EN P1_4 // J12-10 -#define ENET_TXD0 P1_0 // J12-11 -#define ENET_TXD1 P1_1 // J12-12 +#define ENET_MOC P1_16 // (70) J12-3 +#define REF_CLK P1_15 // (72) J12-5 +#define ENET_RXD0 P1_9 // (74) J12-7 +#define ENET_CRS P1_8 // (76) J12-9 +#define ENET_TX_EN P1_4 // (77) J12-10 +#define ENET_TXD0 P1_0 // (78) J12-11 +#define ENET_TXD1 P1_1 // (79) J12-12 /** * PWMS @@ -328,25 +330,25 @@ * * SERVO2 does NOT have a PWM assigned to it. * - * PWM1.1 P0_18 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM - * PWM1.1 P2_0 E0_STEP_PIN - * PWM1.2 P1_20 SERVO0_PIN - * PWM1.2 P2_1 X_STEP_PIN - * PWM1.3 P1_21 SERVO1_PIN J5-1 - * PWM1.3 P2_2 Y_STEP_PIN - * PWM1.4 P1_23 SDSS(SSEL0) J3-5 AUX-3 - * PWM1.4 P2_3 Z_STEP_PIN - * PWM1.5 P1_24 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES - * PWM1.5 P2_4 RAMPS_D9_PIN - * PWM1.6 P1_26 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES - * PWM1.6 P2_5 RAMPS_D10_PIN + * PWM1.1 P0_18 ( 4) SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM + * PWM1.1 P2_0 (26) E0_STEP_PIN + * PWM1.2 P1_20 (11) SERVO0_PIN + * PWM1.2 P2_1 (54) X_STEP_PIN + * PWM1.3 P1_21 ( 6) SERVO1_PIN J5-1 + * PWM1.3 P2_2 (60) Y_STEP_PIN + * PWM1.4 P1_23 (53) SDSS(SSEL0) J3-5 AUX-3 + * PWM1.4 P2_3 (46) Z_STEP_PIN + * PWM1.5 P1_24 ( 3) X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES + * PWM1.5 P2_4 ( 9) RAMPS_D9_PIN + * PWM1.6 P1_26 (14) Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES + * PWM1.6 P2_5 (10) RAMPS_D10_PIN */ /** * special pins - * P1_30 - not 5V tolerant - * P1_31 - not 5V tolerant - * P0_27 - open collector - * P0_28 - open collector + * P1_30 (37) - not 5V tolerant + * P1_31 (49) - not 5V tolerant + * P0_27 (57) - open collector + * P0_28 (58) - open collector * */