diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 98319fc77..7149c020c 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -1302,7 +1302,7 @@ void Temperature::init() { case TIMER5A: case TIMER5B: case TIMER5C: _SET_CS(5, val); break; #endif } - #endif + #endif } #endif // FAST_PWM_FAN diff --git a/Marlin/src/pins/pins_RURAMPS4D.h b/Marlin/src/pins/pins_RURAMPS4D.h index 93bc21a8f..ab15c09f7 100644 --- a/Marlin/src/pins/pins_RURAMPS4D.h +++ b/Marlin/src/pins/pins_RURAMPS4D.h @@ -29,9 +29,7 @@ * * Differences between * RADDS | RuRAMPS4DUE - * A13 | A9/D63 (shares the same pin with AUX2_4PIN) - * A14 | A10/D64 (shares the same pin with AUX2_5PIN) - * A15 | NC + * | */ #ifndef __SAM3X8E__ @@ -39,16 +37,14 @@ #endif #ifndef BOARD_NAME - #define BOARD_NAME "RuRAMPS4Due" + #define BOARD_NAME "RuRAMPS4Due" #endif +#define RURAMPS4DUE // #1550 in boards.h #undef INVERTED_HEATER_PINS #undef INVERTED_BED_PINS #undef INVERTED_FAN_PINS -#define I2C_EEPROM -//#define SPI_EEPROM - // // Servos // @@ -77,18 +73,18 @@ // // Steppers // -#define X_STEP_PIN 37 +#define X_STEP_PIN 37 // Support Extension Board #define X_DIR_PIN 36 #define X_ENABLE_PIN 38 #define X_CS_PIN -1 -#define Y_STEP_PIN 32 +#define Y_STEP_PIN 32 // Support Extension Board #define Y_DIR_PIN 35 #define Y_ENABLE_PIN 34 #define Y_CS_PIN -1 -#define Z_STEP_PIN 30 -#define Z_DIR_PIN 2 +#define Z_STEP_PIN 30 // Support Extension Board +#define Z_DIR_PIN 2 #define Z_ENABLE_PIN 33 #define Z_CS_PIN -1 @@ -102,48 +98,43 @@ #define E1_ENABLE_PIN 26 #define E1_CS_PIN -1 -#define E2_STEP_PIN 25 //14 //sys0724 -#define E2_DIR_PIN 23 //15 -#define E2_ENABLE_PIN 27 //61 +#define E2_STEP_PIN 25 +#define E2_DIR_PIN 23 +#define E2_ENABLE_PIN 27 #define E2_CS_PIN -1 -// For Extension Board V2 -// http://doku.radds.org/dokumentation/extension-board -//#define E3_STEP_PIN 35 -//#define E3_DIR_PIN 33 -//#define E3_ENABLE_PIN 37 -//#define E3_CS_PIN 6 - -//#define Z2_STEP_PIN 29 -//#define Z2_DIR_PIN 27 -//#define Z2_ENABLE_PIN 31 -//#define Z2_CS_PIN 39 +#define E3_STEP_PIN 15 // Only For Extension Board +#define E3_DIR_PIN 14 +#define E3_ENABLE_PIN 61 +#define E3_CS_PIN -1 -// Microstepping pins - Mapping not from fastio.h (?) -//#define E3_MS1_PIN 67 -//#define E3_MS2_PIN 68 -//#define E3_MS3_PIN 69 -//#define Z2_MS1_PIN 67 // shared with E3_MS1_PIN -//#define Z2_MS2_PIN 68 // shared with E3_MS2_PIN -//#define Z2_MS3_PIN 69 // shared with E3_MS3_PIN +// For Future: Microstepping pins - Mapping not from fastio.h (?) +//#define E3_MS1_PIN ? +//#define E3_MS2_PIN ? +//#define E3_MS3_PIN ? +//#define Z2_MS1_PIN ? // shared with E3_MS1_PIN +//#define Z2_MS2_PIN ? // shared with E3_MS2_PIN +//#define Z2_MS3_PIN ? // shared with E3_MS3_PIN // -// Temperature Sensors +// Limit Switches // -#define TEMP_0_PIN 0 // ANALOG NUMBERING #54 -#define TEMP_1_PIN 1 // ANALOG NUMBERING #55 -#define TEMP_2_PIN 2 // ANALOG NUMBERING #56 -#define TEMP_3_PIN 3 // ANALOG NUMBERING #57 -#define TEMP_BED_PIN 4 // ANALOG NUMBERING #58 +#define X_MIN_PIN 45 +#define X_MAX_PIN 39 +#define Y_MIN_PIN 46 +#define Y_MAX_PIN 41 +#define Z_MIN_PIN 47 +#define Z_MAX_PIN 43 -/* -// SPI for Max6675 or Max31855 Thermocouple -#if DISABLED(SDSUPPORT) - #define MAX6675_SS 53 -#else - #define MAX6675_SS 49 +#if !ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) + #define Z_PROBE_PIN 49 +#endif // else Z_PROBE_PIN = Z_MIN_PIN + +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN Y_MIN_PIN + #endif #endif -*/ // // Heaters / Fans @@ -151,18 +142,73 @@ #define HEATER_0_PIN 13 #define HEATER_1_PIN 12 #define HEATER_2_PIN 11 -#define HEATER_BED_PIN 7 // BED H1 +#define HEATER_BED_PIN 7 // BED H1 #define FAN_PIN 9 #define FAN1_PIN 8 +#define CONTROLLER_FAN_PIN -1 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG A0 +#define TEMP_1_PIN 1 // ANALOG A1 +#define TEMP_2_PIN 2 // ANALOG A2 +#define TEMP_3_PIN 3 // ANALOG A2 +#define TEMP_BED_PIN 4 // ANALOG A3 +//Thermocouple Use Analog Pins +#if ENABLED(VER_WITH_THERMOCOUPLE) // If Nead, define is in Configuration.h + #define TEMP_4_PIN 5 // A5 + #define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support) +#endif + +// SPI for Max6675 or Max31855 Thermocouple +//#if DISABLED(SDSUPPORT) +// #define MAX6675_SS 53 +//#else +// #define MAX6675_SS 49 +//#endif + +// +// Servos +// +#define SERVO0_PIN 5 +#define SERVO1_PIN 3 +#define SERVO2_PIN -1 +#define SERVO3_PIN -1 // // Misc. Functions // -#define SDSS 4 // 4,10,52 if using HW SPI. -#define LED_PIN 13 +#define SDSS 4 // 4,10,52 if using HW SPI. +#define LED_PIN -1 // 13 - HEATER_0_PIN +#define SDPOWER -1 +#define PS_ON_PIN -1 // 65 +#define KILL_PIN -1 + +// MKS TFT / Nextion Use internal USART-1 +#define TFT_LCD_MODULE_COM 1 +#define TFT_LCD_MODULE_BAUDRATE 115600 + +// ESP WiFi Use internal USART-2 +#define ESP_WIFI_MODULE_COM 2 +#define ESP_WIFI_MODULE_BAUDRATE 115600 +#define ESP_WIFI_MODULE_RESET_PIN -1 +#define PIGGY_GPIO_PIN -1 -//#define FIL_RUNOUT_PIN Y_MIN_PIN +// +// EEPROM +// +#define E2END 0x8000 // 32Kb (24lc256) +#define I2C_EEPROM // EEPROM on I2C-0 +//#define EEPROM_SD // EEPROM on SDCARD +//#define SPI_EEPROM // EEPROM on SPI-0 +//#define SPI_CHAN_EEPROM1 ? +//#define SPI_EEPROM1_CS ? +// 2K EEPROM +//#define SPI_EEPROM2_CS ? +// 32Mb FLASH +//#define SPI_FLASH_CS ? // // LCD / Controller @@ -186,39 +232,38 @@ #define SD_DETECT_PIN 51 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) - #define LCD_PINS_RS 52 //? - #define LCD_PINS_ENABLE 53 //? - #define LCD_PINS_D4 48 //? - #define LCD_PINS_D5 50 //? - #define LCD_PINS_D6 52 //? - #define LCD_PINS_D7 53 //? + #define LCD_PINS_RS 52 + #define LCD_PINS_ENABLE 53 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 #define BEEPER_PIN 62 - #define BTN_EN1 44 //! - #define BTN_EN2 42 //! + #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + #define BTN_EN1 44 + #define BTN_EN2 42 + #define BTN_ENC 40 + #define SD_DETECT_PIN 51 + #endif + #elif ENABLED(SSD1306_OLED_I2C_CONTROLLER) + #define BTN_EN1 44 + #define BTN_EN2 42 #define BTN_ENC 40 + #define BEEPER_PIN 62 + #define LCD_SDSS 10 #define SD_DETECT_PIN 51 - #elif ENABLED(SSD1306_OLED_I2C_CONTROLLER) - - #define BTN_EN1 44 //? - #define BTN_EN2 42 //? - #define BTN_ENC 40 //? - #define SD_DETECT_PIN 51 //? - - #define BEEPER_PIN 62 //? - #define LCD_SDSS 10 //? - - #elif ENABLED(SPARK_FULL_GRAPHICS) //!!! - check! - - #define LCD_PINS_D4 29 - #define LCD_PINS_ENABLE 27 - #define LCD_PINS_RS 25 - #define BTN_EN1 35 - #define BTN_EN2 33 - #define BTN_ENC 37 - + #elif ENABLED(SPARK_FULL_GRAPHICS) + //http://doku.radds.org/dokumentation/other-electronics/sparklcd/ + #error "Oops! SPARK_FULL_GRAPHICS not supported with this board" + //#define LCD_PINS_D4 29//? + //#define LCD_PINS_ENABLE 27//? + //#define LCD_PINS_RS 25//? + //#define BTN_EN1 35//? + //#define BTN_EN2 33//? + //#define BTN_ENC 37//? #endif // SPARK_FULL_GRAPHICS #endif // ULTRA_LCD