diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 9c566cb3c..99b9a05a0 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1236,9 +1235,8 @@ * SD CARD: SPI SPEED * * Enable one of the following items for a slower SPI transfer speed. - * This may be required to resolve "volume init" errors or LCD issues. + * This may be required to resolve "volume init" errors. */ - //#define SPI_SPEED SPI_HALF_SPEED //#define SPI_SPEED SPI_QUARTER_SPEED //#define SPI_SPEED SPI_EIGHTH_SPEED @@ -1505,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 402c5b18c..fbff1453f 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -576,12 +576,6 @@ // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h index a43d2a0a0..99b9a05a0 100644 --- a/Marlin/src/config/default/Configuration.h +++ b/Marlin/src/config/default/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h index 402c5b18c..fbff1453f 100644 --- a/Marlin/src/config/default/Configuration_adv.h +++ b/Marlin/src/config/default/Configuration_adv.h @@ -576,12 +576,6 @@ // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h index 0be730e33..feee91908 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -982,7 +981,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1524,6 +1523,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h index a87e55d9d..aeab8305f 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h index 8d0b8f622..0910dc4d6 100644 --- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h +++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h index 7e9e4b1be..ff9aedb3d 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1105,7 +1104,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1663,6 +1662,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h index 26f0cecf1..87827bc12 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety @@ -608,7 +601,7 @@ */ //#define BABYSTEPPING #if ENABLED(BABYSTEPPING) - //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way #define BABYSTEP_MULTIPLICATOR 100 // Babysteps are very small. Increase for faster motion. //#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h index 53088a3ed..e7c4b162d 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -968,7 +967,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1512,6 +1511,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h index 195c52074..7c636f162 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h index 0db288ec5..bdd5bfbf6 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -953,7 +952,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1495,6 +1494,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h index 14959bbfb..53fd835f6 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h index 5f07e117e..9349f72ea 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h @@ -90,7 +90,6 @@ // example configuration folder. // #define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -762,6 +761,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -961,7 +962,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1503,6 +1504,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h index 82f0175d2..e958aec43 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h index 7b853cf2d..75314c446 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -953,7 +952,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1495,6 +1494,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h index 14959bbfb..53fd835f6 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h index b9b3dda15..e4b92fefb 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration.h +++ b/Marlin/src/config/examples/Cartesio/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // #define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -961,7 +960,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1503,6 +1502,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h index f3a226fad..ba0cecfa2 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h +++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h old mode 100644 new mode 100755 index 077857416..811e7c359 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // #define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1392,7 +1391,7 @@ // RepRapDiscount FULL GRAPHIC Smart Controller // http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller // -#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER // // MakerLab Mini Panel with graphic @@ -1514,6 +1513,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h index 4294fbdf9..cf13b9cf8 100644 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h @@ -1106,57 +1106,46 @@ //#define E4_IS_L6470 #define X_MICROSTEPS 16 // number of microsteps - #define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high #define X_OVERCURRENT 2000 // maxc current in mA. If the current goes over this value, the driver will switch off #define X_STALLCURRENT 1500 // current in mA where the driver will detect a stall #define X2_MICROSTEPS 16 - #define X2_K_VAL 50 #define X2_OVERCURRENT 2000 #define X2_STALLCURRENT 1500 #define Y_MICROSTEPS 16 - #define Y_K_VAL 50 #define Y_OVERCURRENT 2000 #define Y_STALLCURRENT 1500 #define Y2_MICROSTEPS 16 - #define Y2_K_VAL 50 #define Y2_OVERCURRENT 2000 #define Y2_STALLCURRENT 1500 #define Z_MICROSTEPS 16 - #define Z_K_VAL 50 #define Z_OVERCURRENT 2000 #define Z_STALLCURRENT 1500 #define Z2_MICROSTEPS 16 - #define Z2_K_VAL 50 #define Z2_OVERCURRENT 2000 #define Z2_STALLCURRENT 1500 #define E0_MICROSTEPS 16 - #define E0_K_VAL 50 #define E0_OVERCURRENT 2000 #define E0_STALLCURRENT 1500 #define E1_MICROSTEPS 16 - #define E1_K_VAL 50 #define E1_OVERCURRENT 2000 #define E1_STALLCURRENT 1500 #define E2_MICROSTEPS 16 - #define E2_K_VAL 50 #define E2_OVERCURRENT 2000 #define E2_STALLCURRENT 1500 #define E3_MICROSTEPS 16 - #define E3_K_VAL 50 #define E3_OVERCURRENT 2000 #define E3_STALLCURRENT 1500 #define E4_MICROSTEPS 16 - #define E4_K_VAL 50 #define E4_OVERCURRENT 2000 #define E4_STALLCURRENT 1500 @@ -1298,6 +1287,7 @@ #if ENABLED(CUSTOM_USER_MENUS) #define USER_SCRIPT_DONE "M117 User Script Done" #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script #define USER_DESC_1 "Home & UBL Info" #define USER_GCODE_1 "G28\nG29 W" diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h index 940543c6c..039529bf2 100644 --- a/Marlin/src/config/examples/Felix/Configuration.h +++ b/Marlin/src/config/examples/Felix/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -944,7 +943,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1486,6 +1485,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h index e6e8d741f..e4bd9b0e3 100644 --- a/Marlin/src/config/examples/Felix/Configuration_adv.h +++ b/Marlin/src/config/examples/Felix/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h index 9205c4e02..29aee2fab 100644 --- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h +++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -944,7 +943,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1486,6 +1485,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration.h b/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration.h index 1cd587b0c..14b177107 100644 --- a/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration.h +++ b/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -764,6 +763,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 2 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -965,7 +966,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1507,6 +1508,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration_adv.h index 8f1fc71ee..661cca929 100644 --- a/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration_adv.h +++ b/Marlin/src/config/examples/Folger Tech/i3-2020/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h index 37a8c30d6..bf360df58 100644 --- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h @@ -37,7 +37,7 @@ */ #ifndef CONFIGURATION_H #define CONFIGURATION_H -#define CONFIGURATION_H_VERSION 010100 +#define CONFIGURATION_H_VERSION 020000 //=========================================================================== //============================= Getting Started ============================= @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -977,7 +976,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1519,6 +1518,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 702ed68e4..dfa027f31 100644 --- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -37,7 +37,7 @@ */ #ifndef CONFIGURATION_H #define CONFIGURATION_H -#define CONFIGURATION_H_VERSION 010100 +#define CONFIGURATION_H_VERSION 020000 //=========================================================================== //============================= Getting Started ============================= @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -761,6 +760,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -960,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1502,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h index 61a3cd903..388afeca5 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -966,7 +965,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1508,6 +1507,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h index f0d026ad1..25a841a3a 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h index 41bb37b51..4ec1bd9fe 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h @@ -96,7 +96,6 @@ // example configuration folder. // #define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -990,7 +989,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1532,6 +1531,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h index 7c53fc182..0c9bd5467 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h index ec17af5a2..503b6fe95 100644 --- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h index ad4d2f9a7..4c82d29d0 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration.h +++ b/Marlin/src/config/examples/RigidBot/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -960,7 +959,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h index f687e25ed..baa738881 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h +++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h index 2a93c5152..ce84c341c 100644 --- a/Marlin/src/config/examples/SCARA/Configuration.h +++ b/Marlin/src/config/examples/SCARA/Configuration.h @@ -121,7 +121,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -974,7 +973,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1516,6 +1515,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h index 42ffe17a6..15503d086 100644 --- a/Marlin/src/config/examples/SCARA/Configuration_adv.h +++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h index 897c70a43..f89c16e2d 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h @@ -37,7 +37,7 @@ */ #ifndef CONFIGURATION_H #define CONFIGURATION_H -#define CONFIGURATION_H_VERSION 010100 +#define CONFIGURATION_H_VERSION 020000 //=========================================================================== //============================= Getting Started ============================= @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -792,6 +791,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -991,7 +992,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1533,6 +1534,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h index b8df16589..9c04ad2e8 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h @@ -564,13 +564,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h index e252f5c60..e985e517a 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h @@ -107,7 +107,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1018,7 +1017,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1560,6 +1559,35 @@ // #define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h index 85afa6ed9..2044bba33 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h index 94d0ccf9c..1766f40f0 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h @@ -107,7 +107,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -789,6 +788,9 @@ #define INVERT_E4_DIR true // @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + // K8200: it is usual to have clamps for the glass plate on the heatbed #define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -989,7 +991,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1534,6 +1536,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + #endif // K8200_VM8201 //============================================================================= diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h index bc03354b3..b2e66f0ed 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h @@ -588,13 +588,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h index 23fff324a..65082ad40 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h index 0f46a008d..a80e59195 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h index 0d1099c79..09330100f 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h index 4371d684d..52c414069 100644 --- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h +++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -962,7 +961,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1504,6 +1503,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 8dd3b8aa3..8e6445553 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -885,6 +884,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -1088,7 +1089,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1630,6 +1631,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 0c837ada3..c019636d8 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -577,13 +577,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 198dfea8e..4634d74c3 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -885,6 +884,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -1082,7 +1083,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1623,6 +1624,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 88f8444eb..5a3cfd7b1 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -577,13 +577,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h index 4257c49ba..0338e220a 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration.h +++ b/Marlin/src/config/examples/delta/generic/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1079,7 +1078,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1620,6 +1619,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h index 88f8444eb..5a3cfd7b1 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h @@ -577,13 +577,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h index 599c00518..130345a4d 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1082,7 +1081,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1623,6 +1622,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h index 88f8444eb..5a3cfd7b1 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h @@ -577,13 +577,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h index 9d2b846ee..8b50cc116 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h @@ -95,7 +95,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1082,7 +1081,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1623,6 +1622,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h index 142d59ba6..0582b3a1d 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h @@ -582,13 +582,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h index e47040182..e2100a84c 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -1091,7 +1090,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1632,6 +1631,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h index 8b7c98341..0b633dc26 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h @@ -577,13 +577,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h index 4130c1c82..08496aa60 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // #define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -774,6 +773,8 @@ // @section homing +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + #define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... // Be sure you have this distance over your Z_MAX_POS in case. @@ -974,7 +975,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1516,6 +1517,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 7990eb381..9f82f3d8b 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h index 7fb4b0be1..4f40cfb79 100644 --- a/Marlin/src/config/examples/makibox/Configuration.h +++ b/Marlin/src/config/examples/makibox/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -965,7 +964,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1507,6 +1506,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h index ca090dda4..9f8e4db1b 100644 --- a/Marlin/src/config/examples/makibox/Configuration_adv.h +++ b/Marlin/src/config/examples/makibox/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h index 434fd25b1..c827b56e0 100644 --- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h +++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h @@ -59,14 +59,14 @@ //============================= DELTA Printer =============================== //=========================================================================== // For a Delta printer start with one of the configuration files in the -// example_configurations/delta directory and customize for your machine. +// config/examples/delta directory and customize for your machine. // //=========================================================================== //============================= SCARA Printer =============================== //=========================================================================== // For a SCARA printer start with the configuration files in -// example_configurations/SCARA and customize for your machine. +// config/examples/SCARA and customize for your machine. // // @section info diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h index 4e6a260d7..7408c536f 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -957,7 +956,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1499,6 +1498,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h index 853fc5445..14799b07a 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h index b9a858205..1b7eb5730 100644 --- a/Marlin/src/config/examples/wt150/Configuration.h +++ b/Marlin/src/config/examples/wt150/Configuration.h @@ -91,7 +91,6 @@ // example configuration folder. // //#define SHOW_CUSTOM_BOOTSCREEN - // @section machine /** @@ -967,7 +966,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -#define LEVEL_BED_CORNERS +//#define LEVEL_BED_CORNERS /** * Commands to execute at the end of G29 probing. @@ -1509,6 +1508,35 @@ // //#define OLED_PANEL_TINYBOY2 +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + //============================================================================= //=============================== Extra Features ============================== //============================================================================= diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h index 8d1ee372c..4320205f2 100644 --- a/Marlin/src/config/examples/wt150/Configuration_adv.h +++ b/Marlin/src/config/examples/wt150/Configuration_adv.h @@ -575,13 +575,6 @@ // Enable this option and reduce the value to optimize screen updates. // The normal delay is 10µs. Use the lowest value that still gives a reliable display. //#define DOGM_SPI_DELAY_US 5 - - // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. - #if ENABLED(VIKI2) || ENABLED(miniVIKI) - #define DOGLCD_SCK SCK_PIN - #define DOGLCD_MOSI MOSI_PIN - #endif - #endif // DOGLCD // @section safety diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 0f79edbbc..69ca4363b 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -40,17 +40,8 @@ #elif ENABLED(MAKRPANEL) - #define DOGLCD - #define ULTIPANEL - #define DEFAULT_LCD_CONTRAST 17 #define U8GLIB_ST7565_64128N - #elif ENABLED(MINIPANEL) - - #define DOGLCD - #define ULTIPANEL - #define DEFAULT_LCD_CONTRAST 17 - #elif ENABLED(ANET_KEYPAD_LCD) #define REPRAPWORLD_KEYPAD @@ -116,6 +107,34 @@ #define U8GLIB_ST7920 #define ULTIPANEL + #elif ENABLED(CR10_STOCKDISPLAY) + + #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + #ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_2_NOP + #endif + #ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_2_NOP + #endif + #ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_2_NOP + #endif + + #elif ENABLED(MKS_12864OLED) + + #define REPRAP_DISCOUNT_SMART_CONTROLLER + #define U8GLIB_SH1106 + + #elif ENABLED(MKS_MINI_12864) + + #define MINIPANEL + + #endif + + #if ENABLED(MAKRPANEL) || ENABLED(MINIPANEL) + #define DOGLCD + #define ULTIPANEL + #define DEFAULT_LCD_CONTRAST 17 #endif // Generic support for SSD1306 / SH1106 OLED based LCDs. @@ -125,7 +144,15 @@ #endif #if ENABLED(PANEL_ONE) || ENABLED(U8GLIB_SH1106) + #define ULTIMAKERCONTROLLER + + #elif ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) + + #define REPRAP_DISCOUNT_SMART_CONTROLLER + #define LCD_WIDTH 16 + #define LCD_HEIGHT 2 + #endif #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(LCD_FOR_MELZI) @@ -249,14 +276,12 @@ #ifndef LCD_HEIGHT #define LCD_HEIGHT 4 #endif - #else // no panel but just LCD - #if ENABLED(ULTRA_LCD) - #ifndef LCD_WIDTH - #define LCD_WIDTH 16 - #endif - #ifndef LCD_HEIGHT - #define LCD_HEIGHT 2 - #endif + #elif ENABLED(ULTRA_LCD) // no panel but just LCD + #ifndef LCD_WIDTH + #define LCD_WIDTH 16 + #endif + #ifndef LCD_HEIGHT + #define LCD_HEIGHT 2 #endif #endif diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index c86a665b0..d2dac428c 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -856,6 +856,18 @@ #endif #endif + /** + * VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined. + */ + #if ENABLED(VIKI2) || ENABLED(miniVIKI) + #ifndef DOGLCD_SCK + #define DOGLCD_SCK SCK_PIN + #endif + #ifndef DOGLCD_MOSI + #define DOGLCD_MOSI MOSI_PIN + #endif + #endif + /** * Z_HOMING_HEIGHT / Z_CLEARANCE_BETWEEN_PROBES */ diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index d841d6cbf..e3b430f6a 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -1137,6 +1137,7 @@ static_assert(1 >= 0 * Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER * SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER + * MKS_12864OLED => U8GLIB_SH1106 => ULTIMAKERCONTROLLER * miniVIKI => ULTIMAKERCONTROLLER * VIKI2 => ULTIMAKERCONTROLLER * ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER @@ -1144,19 +1145,34 @@ static_assert(1 >= 0 */ static_assert(1 >= 0 #if ENABLED(ULTIMAKERCONTROLLER) \ - && DISABLED(SAV_3DGLCD) && DISABLED(miniVIKI) && DISABLED(VIKI2) \ - && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) && DISABLED(PANEL_ONE) + && DISABLED(SAV_3DGLCD) \ + && DISABLED(miniVIKI) \ + && DISABLED(VIKI2) \ + && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ + && DISABLED(PANEL_ONE) \ + && DISABLED(MKS_12864OLED) + 1 #endif - #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(LCD_FOR_MELZI) + #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) \ + && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \ + && DISABLED(LCD_FOR_MELZI) \ + && DISABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + && DISABLED(MKS_12864OLED) + 1 #endif - #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER) + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \ + && DISABLED(BQ_LCD_SMART_CONTROLLER) + 1 #endif #if ENABLED(LCD_FOR_MELZI) + 1 #endif + #if ENABLED(MKS_12864OLED) + + 1 + #endif + #if ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) + + 1 + #endif #if ENABLED(CARTESIO_UI) + 1 #endif @@ -1181,10 +1197,15 @@ static_assert(1 >= 0 #if ENABLED(G3D_PANEL) + 1 #endif - #if ENABLED(MINIPANEL) + #if ENABLED(MINIPANEL) && DISABLED(MKS_MINI_12864) + + 1 + #endif + #if ENABLED(MKS_MINI_12864) + 1 #endif - #if ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI) && DISABLED(ANET_KEYPAD_LCD) + #if ENABLED(REPRAPWORLD_KEYPAD) \ + && DISABLED(CARTESIO_UI) \ + && DISABLED(ANET_KEYPAD_LCD) + 1 #endif #if ENABLED(RIGIDBOT_PANEL) @@ -1286,6 +1307,16 @@ static_assert(1 >= 0 #error "HAVE_L6470DRIVER requires at least one L6470 stepper to be set." #endif +/** + * Digipot requirement + */ +#if ENABLED(DIGIPOT_MCP4018) + #if !defined(DIGIPOTS_I2C_SDA_X) || !defined(DIGIPOTS_I2C_SDA_Y) || !defined(DIGIPOTS_I2C_SDA_Z) \ + || !defined(DIGIPOTS_I2C_SDA_E0) || !defined(DIGIPOTS_I2C_SDA_E1) + #error "DIGIPOT_MCP4018 requires DIGIPOTS_I2C_SDA_* pins to be defined." + #endif +#endif + /** * Require 4 or more elements in per-axis initializers */ diff --git a/Marlin/src/lcd/dogm/ultralcd_st7565_u8glib_VIKI.h b/Marlin/src/lcd/dogm/ultralcd_st7565_u8glib_VIKI.h index 772ede121..a86238885 100644 --- a/Marlin/src/lcd/dogm/ultralcd_st7565_u8glib_VIKI.h +++ b/Marlin/src/lcd/dogm/ultralcd_st7565_u8glib_VIKI.h @@ -27,17 +27,11 @@ #if ENABLED(U8GLIB_ST7565_64128N) - #define ST7565_CLK_PIN DOGLCD_SCK #define ST7565_DAT_PIN DOGLCD_MOSI #define ST7565_CS_PIN DOGLCD_CS #define ST7565_A0_PIN DOGLCD_A0 - - - - - #include #define WIDTH 128 @@ -92,7 +86,6 @@ #define ST7565_DELAY_3 CPU_ST7565_DELAY_3 #endif - #if ENABLED(SHARED_SPI) // Re-ARM requires that the LCD and the SD card share a single SPI #define ST7565_WRITE_BYTE(a) { spiSend((uint8_t)a); U8G_DELAY; } @@ -135,8 +128,7 @@ uint8_t u8g_dev_st7565_64128n_2x_VIKI_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) { switch (msg) { - case U8G_DEV_MSG_INIT: - { + case U8G_DEV_MSG_INIT: { OUT_WRITE(ST7565_CS_PIN, LOW); #if ENABLED(SHARED_SPI) u8g_Delay(250); @@ -155,52 +147,50 @@ uint8_t u8g_dev_st7565_64128n_2x_VIKI_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg ST7565_NA0(); /* instruction mode */ ST7565_NCS(); /* enable chip */ - - ST7565_WRITE_BYTE(0x0A2); /* 0x0a2: LCD bias 1/9 (according to Displaytech 64128N datasheet) */ + ST7565_WRITE_BYTE(0x0A2); /* 0x0A2: LCD bias 1/9 (according to Displaytech 64128N datasheet) */ ST7565_WRITE_BYTE(0x0A0); /* Normal ADC Select (according to Displaytech 64128N datasheet) */ - ST7565_WRITE_BYTE(0x0c8); /* common output mode: set scan direction normal operation/SHL Select; 0x0c0 --> SHL = 0; normal; 0x0c8 --> SHL = 1 */ + ST7565_WRITE_BYTE(0x0C8); /* common output mode: set scan direction normal operation/SHL Select; 0x0C0 --> SHL = 0; normal; 0x0C8 --> SHL = 1 */ ST7565_WRITE_BYTE(0x040); /* Display start line for Displaytech 64128N */ ST7565_WRITE_BYTE(0x028 | 0x04); /* power control: turn on voltage converter */ -// U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ + //U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ ST7565_WRITE_BYTE(0x028 | 0x06); /* power control: turn on voltage regulator */ -// U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ + //U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ ST7565_WRITE_BYTE(0x028 | 0x07); /* power control: turn on voltage follower */ -// U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ - + //U8G_ESC_DLY(50); /* delay 50 ms - hangs after a reset if used */ ST7565_WRITE_BYTE(0x010); /* Set V0 voltage resistor ratio. Setting for controlling brightness of Displaytech 64128N */ - ST7565_WRITE_BYTE(0x0a6); /* display normal, bit val 0: LCD pixel off. */ + ST7565_WRITE_BYTE(0x0A6); /* display normal, bit val 0: LCD pixel off. */ ST7565_WRITE_BYTE(0x081); /* set contrast */ - ST7565_WRITE_BYTE(0x01e); /* Contrast value. Setting for controlling brightness of Displaytech 64128N */ + ST7565_WRITE_BYTE(0x01E); /* Contrast value. Setting for controlling brightness of Displaytech 64128N */ - - ST7565_WRITE_BYTE(0x0af); /* display on */ + ST7565_WRITE_BYTE(0x0AF); /* display on */ U8G_ESC_DLY(100); /* delay 100 ms */ - ST7565_WRITE_BYTE(0x0a5); /* display all points; ST7565 */ + ST7565_WRITE_BYTE(0x0A5); /* display all points; ST7565 */ U8G_ESC_DLY(100); /* delay 100 ms */ U8G_ESC_DLY(100); /* delay 100 ms */ - ST7565_WRITE_BYTE(0x0a4); /* normal display */ + ST7565_WRITE_BYTE(0x0A4); /* normal display */ ST7565_CS(); /* disable chip */ } /* end of sequence */ - break; - case U8G_DEV_MSG_STOP: - break; - case U8G_DEV_MSG_PAGE_NEXT: - { u8g_pb_t *pb = (u8g_pb_t *)(dev->dev_mem); + break; + + case U8G_DEV_MSG_STOP: break; + + case U8G_DEV_MSG_PAGE_NEXT: { + u8g_pb_t *pb = (u8g_pb_t *)(dev->dev_mem); ST7565_CS(); /* disable chip */ ST7565_NA0(); /* instruction mode */ ST7565_NCS(); /* enable chip */ ST7565_WRITE_BYTE(0x010); /* set upper 4 bit of the col adr to 0x10 */ ST7565_WRITE_BYTE(0x000); /* set lower 4 bit of the col adr to 0x00. Changed for DisplayTech 64128N */ /* end of sequence */ - ST7565_WRITE_BYTE(0x0b0 | (2*pb->p.page));; /* select current page (ST7565R) */ + ST7565_WRITE_BYTE(0x0B0 | (2*pb->p.page));; /* select current page (ST7565R) */ ST7565_A0(); /* data mode */ ST7560_WriteSequence( (uint8_t) pb->width, (uint8_t *)pb->buf); ST7565_CS(); /* disable chip */ @@ -209,12 +199,13 @@ uint8_t u8g_dev_st7565_64128n_2x_VIKI_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg ST7565_WRITE_BYTE(0x010); /* set upper 4 bit of the col adr to 0x10 */ ST7565_WRITE_BYTE(0x000); /* set lower 4 bit of the col adr to 0x00. Changed for DisplayTech 64128N */ /* end of sequence */ - ST7565_WRITE_BYTE(0x0b0 | (2*pb->p.page+1)); /* select current page (ST7565R) */ + ST7565_WRITE_BYTE(0x0B0 | (2*pb->p.page+1)); /* select current page (ST7565R) */ ST7565_A0(); /* data mode */ ST7560_WriteSequence( (uint8_t) pb->width, (uint8_t *)(pb->buf)+pb->width); ST7565_CS(); /* disable chip */ } - break; + break; + case U8G_DEV_MSG_CONTRAST: ST7565_NCS(); ST7565_NA0(); /* instruction mode */ @@ -222,21 +213,23 @@ uint8_t u8g_dev_st7565_64128n_2x_VIKI_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg ST7565_WRITE_BYTE((*(uint8_t *)arg) >> 2); ST7565_CS(); /* disable chip */ return 1; + case U8G_DEV_MSG_SLEEP_ON: ST7565_NA0(); /* instruction mode */ ST7565_NCS(); /* enable chip */ - ST7565_WRITE_BYTE(0x0ac); /* static indicator off */ + ST7565_WRITE_BYTE(0x0AC); /* static indicator off */ ST7565_WRITE_BYTE(0x000); /* indicator register set (not sure if this is required) */ - ST7565_WRITE_BYTE(0x0ae); /* display off */ - ST7565_WRITE_BYTE(0x0a5); /* all points on */ + ST7565_WRITE_BYTE(0x0AE); /* display off */ + ST7565_WRITE_BYTE(0x0A5); /* all points on */ ST7565_CS(); /* disable chip , bugfix 12 nov 2014 */ /* end of sequence */ return 1; + case U8G_DEV_MSG_SLEEP_OFF: ST7565_NA0(); /* instruction mode */ ST7565_NCS(); /* enable chip */ - ST7565_WRITE_BYTE(0x0a4); /* all points off */ - ST7565_WRITE_BYTE(0x0af); /* display on */ + ST7565_WRITE_BYTE(0x0A4); /* all points off */ + ST7565_WRITE_BYTE(0x0AF); /* display on */ U8G_ESC_DLY(50); /* delay 50 ms */ ST7565_CS(); /* disable chip , bugfix 12 nov 2014 */ /* end of sequence */ @@ -260,8 +253,6 @@ class U8GLIB_ST7565_64128n_2x_VIKI : public U8GLIB { { } }; - - #pragma GCC reset_options #endif // U8GLIB_ST7565 diff --git a/Marlin/src/lcd/ultralcd_impl_DOGM.h b/Marlin/src/lcd/ultralcd_impl_DOGM.h index 9da4e5654..f9f1abcfe 100644 --- a/Marlin/src/lcd/ultralcd_impl_DOGM.h +++ b/Marlin/src/lcd/ultralcd_impl_DOGM.h @@ -192,6 +192,10 @@ // Generic support for SSD1306 OLED I2C LCDs //U8GLIB_SSD1306_128X64 u8g(U8G_I2C_OPT_NONE | U8G_I2C_OPT_FAST); // 8 stripes U8GLIB_SSD1306_128X64_2X u8g(U8G_I2C_OPT_NONE | U8G_I2C_OPT_FAST); // 4 stripes +#elif ENABLED(MKS_12864OLED) + // MKS 128x64 (SH1106) OLED I2C LCD + U8GLIB_SH1106_128X64 u8g(DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0); // 8 stripes + //U8GLIB_SH1106_128X64_2X u8g(DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0); // 4 stripes #elif ENABLED(U8GLIB_SH1106) // Generic support for SH1106 OLED I2C LCDs //U8GLIB_SH1106_128X64 u8g(U8G_I2C_OPT_NONE | U8G_I2C_OPT_FAST); // 8 stripes diff --git a/Marlin/src/pins/pins_AZTEEG_X3.h b/Marlin/src/pins/pins_AZTEEG_X3.h index efe9e2f0f..86ccbd924 100644 --- a/Marlin/src/pins/pins_AZTEEG_X3.h +++ b/Marlin/src/pins/pins_AZTEEG_X3.h @@ -50,6 +50,9 @@ // // LCD / Controller // +#undef STAT_LED_RED_PIN +#undef STAT_LED_BLUE_PIN + #if ENABLED(VIKI2) || ENABLED(miniVIKI) #undef DOGLCD_A0 @@ -59,8 +62,6 @@ #define DOGLCD_CS 32 #define BTN_ENC 12 - #undef STAT_LED_RED_PIN - #undef STAT_LED_BLUE_PIN #define STAT_LED_RED_PIN 64 #define STAT_LED_BLUE_PIN 63 diff --git a/Marlin/src/pins/pins_AZTEEG_X3_PRO.h b/Marlin/src/pins/pins_AZTEEG_X3_PRO.h index 0e76a2a23..f44beb512 100644 --- a/Marlin/src/pins/pins_AZTEEG_X3_PRO.h +++ b/Marlin/src/pins/pins_AZTEEG_X3_PRO.h @@ -138,7 +138,7 @@ #undef BEEPER_PIN #define BEEPER_PIN 12 // 33 isn't physically available to the LCD display #else - #define STAT_LED_RED_PIN 32 + #define STAT_LED_RED_PIN 32 #define STAT_LED_BLUE_PIN 35 #endif diff --git a/Marlin/src/pins/pins_RAMPS.h b/Marlin/src/pins/pins_RAMPS.h index d0795ce10..7371fe835 100644 --- a/Marlin/src/pins/pins_RAMPS.h +++ b/Marlin/src/pins/pins_RAMPS.h @@ -63,7 +63,7 @@ // // Servos // -#if ENABLED(IS_RAMPS_13) +#ifdef IS_RAMPS_13 #define SERVO0_PIN 7 // RAMPS_13 // Will conflict with BTN_EN2 on LCD_I2C_VIKI #else #define SERVO0_PIN 11 @@ -243,54 +243,107 @@ // // Průša i3 MK2 Multiplexer Support // -#define E_MUX0_PIN 40 // Z_CS_PIN -#define E_MUX1_PIN 42 // E0_CS_PIN -#define E_MUX2_PIN 44 // E1_CS_PIN +#ifndef E_MUX0_PIN + #define E_MUX0_PIN 40 // Z_CS_PIN +#endif +#ifndef E_MUX1_PIN + #define E_MUX1_PIN 42 // E0_CS_PIN +#endif +#ifndef E_MUX2_PIN + #define E_MUX2_PIN 44 // E1_CS_PIN +#endif + +////////////////////////// +// LCDs and Controllers // +////////////////////////// -// -// LCD / Controller -// #if ENABLED(ULTRA_LCD) + // + // LCD Display output pins + // #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + #define LCD_PINS_RS 49 // CS chip select /SS chip slave select #define LCD_PINS_ENABLE 51 // SID (MOSI) #define LCD_PINS_D4 52 // SCK (CLK) clock + #elif ENABLED(NEWPANEL) && ENABLED(PANEL_ONE) + #define LCD_PINS_RS 40 #define LCD_PINS_ENABLE 42 #define LCD_PINS_D4 65 #define LCD_PINS_D5 66 #define LCD_PINS_D6 44 #define LCD_PINS_D7 64 + #else - #define LCD_PINS_RS 16 - #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 25 + + #if DISABLED(NEWPANEL) + #define BEEPER_PIN 37 + #endif + + #else + + #if ENABLED(MKS_12864OLED) + #define LCD_PINS_DC 25 // Set as output on init + #define LCD_PINS_RS 27 // Pull low for 1s to init + // DOGM SPI LCD Support + #define DOGLCD_CS 16 + #define DOGLCD_MOSI 17 + #define DOGLCD_SCK 23 + #define DOGLCD_A0 LCD_PINS_DC + #else + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #endif + + #define LCD_PINS_D7 29 + + #if DISABLED(NEWPANEL) + #define BEEPER_PIN 33 + #endif + + #endif + #if DISABLED(NEWPANEL) - #define BEEPER_PIN 33 // Buttons are attached to a shift register // Not wired yet - //#define SHIFT_CLK 38 - //#define SHIFT_LD 42 - //#define SHIFT_OUT 40 - //#define SHIFT_EN 17 + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 #endif + #endif + // + // LCD Display input pins + // #if ENABLED(NEWPANEL) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) #define BEEPER_PIN 37 - #define BTN_EN1 31 - #define BTN_EN2 33 - #define BTN_ENC 35 + #if ENABLED(CR10_STOCKDISPLAY) + #define BTN_EN1 17 + #define BTN_EN2 23 + #else + #define BTN_EN1 31 + #define BTN_EN2 33 + #endif + #define BTN_ENC 35 #define SD_DETECT_PIN 49 #define KILL_PIN 41 @@ -311,85 +364,112 @@ #define BTN_EN2 43 #define BTN_ENC 32 #define LCD_SDSS 53 - #define SD_DETECT_PIN -1 #define KILL_PIN 41 #elif ENABLED(LCD_I2C_VIKI) #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. - #define BTN_ENC -1 + #define LCD_SDSS 53 #define SD_DETECT_PIN 49 #elif ENABLED(VIKI2) || ENABLED(miniVIKI) - #define BEEPER_PIN 33 - - // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 44 #define DOGLCD_CS 45 + #define DOGLCD_A0 44 #define LCD_SCREEN_ROT_180 + #define BEEPER_PIN 33 + #define STAT_LED_RED_PIN 32 + #define STAT_LED_BLUE_PIN 35 + #define BTN_EN1 22 #define BTN_EN2 7 #define BTN_ENC 39 #define SDSS 53 #define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board - #define KILL_PIN 31 - #define STAT_LED_RED_PIN 32 - #define STAT_LED_BLUE_PIN 35 - #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) + + #define DOGLCD_CS 29 + #define DOGLCD_A0 27 + + #define BEEPER_PIN 23 + #define LCD_BACKLIGHT_PIN 33 + #define BTN_EN1 35 #define BTN_EN2 37 #define BTN_ENC 31 - #define SD_DETECT_PIN 49 + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 #define KILL_PIN 41 - #define BEEPER_PIN 23 - #define DOGLCD_CS 29 + + #elif ENABLED(MKS_MINI_12864) // Added in Marlin 1.1.6 + #define DOGLCD_A0 27 - #define LCD_BACKLIGHT_PIN 33 + #define DOGLCD_CS 25 + + // GLCD features + //#define LCD_CONTRAST 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #define BEEPER_PIN 37 + // not connected to a pin + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + + #define SDSS 53 + #define SD_DETECT_PIN 49 + #define KILL_PIN 64 + #elif ENABLED(MINIPANEL) + #define BEEPER_PIN 42 - // Pins for DOGM SPI LCD Support + // not connected to a pin + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + #define DOGLCD_A0 44 #define DOGLCD_CS 66 - #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 - #define SDSS 53 - #define KILL_PIN 64 // GLCD features //#define LCD_CONTRAST 190 // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 - // The encoder and click button + #define BTN_EN1 40 #define BTN_EN2 63 #define BTN_ENC 59 - // not connected to a pin + + #define SDSS 53 #define SD_DETECT_PIN 49 + #define KILL_PIN 64 #else // Beeper on AUX-4 #define BEEPER_PIN 33 - // buttons are directly attached using AUX-2 + // Buttons are directly attached using AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) - #define BTN_EN1 64 - #define BTN_EN2 59 - #define BTN_ENC 63 #define SHIFT_OUT 40 #define SHIFT_CLK 44 #define SHIFT_LD 42 + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 #elif ENABLED(PANEL_ONE) #define BTN_EN1 59 // AUX2 PIN 3 #define BTN_EN2 63 // AUX2 PIN 4 @@ -403,8 +483,6 @@ #if ENABLED(G3D_PANEL) #define SD_DETECT_PIN 49 #define KILL_PIN 41 - #else - //#define SD_DETECT_PIN -1 // Ramps doesn't use this #endif #endif diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/pins_RAMPS_RE_ARM.h index bc33ee4de..80cb0abaf 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/pins_RAMPS_RE_ARM.h @@ -247,12 +247,11 @@ #define DOGLCD_A0 59 // J3-8 & AUX-2 #define DOGLCD_CS 63 // J5-3 & AUX-2 -#ifdef ULTIPANEL - - #define LCD_PINS_D5 71 // ENET_MDIO - #define LCD_PINS_D6 73 // ENET_RX_ER - #define LCD_PINS_D7 75 // ENET_RXD1 -#endif + #ifdef ULTIPANEL + #define LCD_PINS_D5 71 // ENET_MDIO + #define LCD_PINS_D6 73 // ENET_RX_ER + #define LCD_PINS_D7 75 // ENET_RXD1 + #endif #if ENABLED(NEWPANEL) #if ENABLED(REPRAPWORLD_KEYPAD) @@ -267,21 +266,21 @@ //#define SHIFT_EN 41 // J5-4 & AUX-4 #endif - #define SDCARD_SORT_ALPHA // Using SORT feature to keep one directory level in RAM - // When going up/down directory levels the SD card is - // accessed but the garbage/lines are removed when the - // LCD updates + #define SDCARD_SORT_ALPHA // Using SORT feature to keep one directory level in RAM + // When going up/down directory levels the SD card is + // accessed but the garbage/lines are removed when the + // LCD updates - #define SDSORT_LIMIT 256 // Maximum number of sorted items (10-256). Costs 27 bytes each. - #define FOLDER_SORTING -1 // -1=above 0=none 1=below - #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. - #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. - #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) - #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. - #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_LIMIT 256 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! - #if ENABLED(VIKI2) || ENABLED(miniVIKI) -// #define LCD_SCREEN_ROT_180 + #if ENABLED(VIKI2) || ENABLED(miniVIKI) + // #define LCD_SCREEN_ROT_180 #undef BEEPER_PIN #define BEEPER_PIN 37 // may change if cable changes @@ -309,12 +308,12 @@ #define STAT_LED_BLUE_PIN 63 // may change if cable changes #define STAT_LED_RED_PIN 6 // may change if cable changes #endif + //#define MISO_PIN 50 // system defined J3-10 & AUX-3 //#define MOSI_PIN 51 // system defined J3-10 & AUX-3 //#define SCK_PIN 52 // system defined J3-9 & AUX-3 //#define SS_PIN 53 // system defined J3-5 & AUX-3 - sometimes called SDSS - #if ENABLED(MINIPANEL) // GLCD features //#define LCD_CONTRAST 190