diff --git a/Marlin/src/HAL/HAL_STM32/HAL.cpp b/Marlin/src/HAL/HAL_STM32/HAL.cpp index ab61e57bf..0eaee0711 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL.cpp +++ b/Marlin/src/HAL/HAL_STM32/HAL.cpp @@ -36,8 +36,10 @@ #if ENABLED(EEPROM_EMULATED_WITH_SRAM) #if STM32F7xx #include "stm32f7xx_ll_pwr.h" + #elif STM32F4xx + #include "stm32f4xx_ll_pwr.h" #else - #error "EEPROM_EMULATED_WITH_SRAM is currently only supported for STM32F7xx" + #error "EEPROM_EMULATED_WITH_SRAM is currently only supported for STM32F4xx and STM32F7xx" #endif #endif // EEPROM_EMULATED_WITH_SRAM diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 120bb3485..cfebabe1b 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -253,6 +253,8 @@ #define BOARD_STM32F4 1804 // STM32 STM32GENERIC based STM32F4 controller #define BOARD_ARMED 1807 // Arm'ed STM32F4 based controller #define BOARD_RUMBA32 1809 // RUMBA32 STM32F4 based controller +#define BOARD_BLACK_STM32F407VE 1810 // BLACK_STM32F407VE +#define BOARD_BLACK_STM32F407ZE 1811 // BLACK_STM32F407ZE #define BOARD_STEVAL 1866 // STEVAL-3DP001V1 3D PRINTER BOARD // diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 19afa1c55..c3ece1346 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -417,7 +417,7 @@ #elif MB(MORPHEUS) #include "pins_MORPHEUS.h" // STM32F1 env:STM32F1 #elif MB(MKS_ROBIN) - #include "pins_MKS_ROBIN.h" // STM32F1 env:STM32F1 + #include "pins_MKS_ROBIN.h" // STM32F1 env:mks_robin // // STM32 ARM Cortex-M4F @@ -435,9 +435,13 @@ #include "pins_ARMED.h" // STM32F4 env:ARMED #elif MB(RUMBA32) #include "pins_RUMBA32.h" // STM32F4 env:RUMBA32 +#elif MB(BLACK_STM32F407VE) + #include "pins_BLACK_STM32F407VE.h" // STM32F4 env:black_stm32f407ve #elif MB(STEVAL) #include "pins_STEVAL.h" // STM32F4 env:STM32F4 + + // // ARM Cortex M7 // diff --git a/Marlin/src/pins/pins_BLACK_STM32F407VE.h b/Marlin/src/pins/pins_BLACK_STM32F407VE.h new file mode 100644 index 000000000..477bb909a --- /dev/null +++ b/Marlin/src/pins/pins_BLACK_STM32F407VE.h @@ -0,0 +1,131 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * STM32F407VET6 with RAMPS-like shield + * 'Black' STM32F407VET6 board - http://wiki.stm32duino.com/index.php?title=STM32F407 + * Shield - https://github.com/jmz52/Hardware + */ + +#pragma once + +#if !defined(STM32F4) && !defined(STM32F4xx) + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#endif + +#define DEFAULT_MACHINE_NAME "STM32F407VET6" +//#define BOARD_NAME "Black STM32F4VET6" + +//#define I2C_EEPROM +//#define E2END 0x1FFF // EEPROM end address (8kB) +#define EEPROM_EMULATED_WITH_SRAM + +#if HOTENDS > 2 || E_STEPPERS > 2 + #error "Black STM32F4VET6 supports up to 2 hotends / E-steppers." +#endif + +// +// Servos +// +#define SERVO0_PIN PC6 +#define SERVO1_PIN PC7 + +// +// Limit Switches +// +#define X_MIN_PIN PC13 +#define X_MAX_PIN PA15 +#define Y_MIN_PIN PA5 +#define Y_MAX_PIN PD12 +#define Z_MIN_PIN PD14 +#define Z_MAX_PIN PD15 + +// +// Steppers +// +#define X_STEP_PIN PC4 +#define X_DIR_PIN PA4 +#define X_ENABLE_PIN PE7 + +#define Y_STEP_PIN PE5 +#define Y_DIR_PIN PE2 +#define Y_ENABLE_PIN PE6 + +#define Z_STEP_PIN PD5 +#define Z_DIR_PIN PD3 +#define Z_ENABLE_PIN PD6 + +#define E0_STEP_PIN PD7 +#define E0_DIR_PIN PD0 +#define E0_ENABLE_PIN PB9 + +#define E1_STEP_PIN PE0 +#define E1_DIR_PIN PE1 +#define E1_ENABLE_PIN PB8 + +// +// Temperature Sensors +// +#define TEMP_0_PIN PC0 // T0 +#define TEMP_1_PIN PC1 // T1 +#define TEMP_BED_PIN PC2 // TB +#define TEMP_CHAMBER_PIN PC3 // TC + +// +// Heaters / Fans +// +#define HEATER_0_PIN PA2 // Heater0 +#define HEATER_1_PIN PA3 // Heater1 +#define HEATER_BED_PIN PA1 // Hotbed + +#define FAN_PIN PE9 // Fan0 +#define FAN1_PIN PE11 // Fan1 +#define FAN2_PIN PE13 // Fan2 +#define FAN3_PIN PE14 // Fan3 + +// +// Misc. Functions +// +#define SDSS PB12 +#define LED_PIN PA6 +//#define LED_PIN PA7 +#define KILL_PIN PB1 + +// +// LCD / Controller +// +#define SD_DETECT_PIN PC5 +//#define SD_DETECT_PIN PA8 // SDIO SD_DETECT_PIN, external SDIO card reader only + +#define BEEPER_PIN PD10 +#define LCD_PINS_RS PE15 +#define LCD_PINS_ENABLE PD8 +#define LCD_PINS_D4 PE10 +#define LCD_PINS_D5 PE12 +#define LCD_PINS_D6 PD1 +#define LCD_PINS_D7 PE8 +#define BTN_ENC PD9 +#define BTN_EN1 PD4 +#define BTN_EN2 PD13 + +#define DOGLCD_CS LCD_PINS_D5 +#define DOGLCD_A0 LCD_PINS_D6 diff --git a/buildroot/share/PlatformIO/boards/blackSTM32F407VET6.json b/buildroot/share/PlatformIO/boards/blackSTM32F407VET6.json new file mode 100644 index 000000000..c55d7cc80 --- /dev/null +++ b/buildroot/share/PlatformIO/boards/blackSTM32F407VET6.json @@ -0,0 +1,65 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m4", + "extra_flags": "-DSTM32F407xx", + "f_cpu": "168000000L", + "hwids": [ + [ + "0x1EAF", + "0x0003" + ], + [ + "0x0483", + "0x3748" + ] + ], + "ldscript": "stm32f407xe.ld", + "mcu": "stm32f407vet6", + "variant": "MARLIN_F407VE" + }, + "debug": { + "jlink_device": "STM32F407VE", + "openocd_target": "stm32f4x", + "svd_path": "STM32F40x.svd", + "tools": { + "stlink": { + "server": { + "arguments": [ + "-f", + "scripts/interface/stlink.cfg", + "-c", + "transport select hla_swd", + "-f", + "scripts/target/stm32f4x.cfg", + "-c", + "reset_config none" + ], + "executable": "bin/openocd", + "package": "tool-openocd" + } + } + } + }, + "frameworks": [ + "arduino", + "stm32cube" + ], + "name": "STM32F407VE (192k RAM. 512k Flash)", + "upload": { + "disable_flushing": false, + "maximum_ram_size": 131072, + "maximum_size": 514288, + "protocol": "stlink", + "protocols": [ + "stlink", + "dfu", + "jlink" + ], + "require_upload_port": true, + "use_1200bps_touch": false, + "wait_for_upload_port": false + }, + "url": "http://www.st.com/en/microcontrollers/stm32f407ve.html", + "vendor": "Generic" +} diff --git a/buildroot/share/PlatformIO/scripts/black_stm32f407vet6.py b/buildroot/share/PlatformIO/scripts/black_stm32f407vet6.py new file mode 100644 index 000000000..cc43893d0 --- /dev/null +++ b/buildroot/share/PlatformIO/scripts/black_stm32f407vet6.py @@ -0,0 +1,29 @@ +import os,shutil +from SCons.Script import DefaultEnvironment +from platformio import util + +env = DefaultEnvironment() +platform = env.PioPlatform() +board = env.BoardConfig() + +FRAMEWORK_DIR = platform.get_package_dir("framework-arduinoststm32") +CMSIS_DIR = os.path.join(FRAMEWORK_DIR, "CMSIS", "CMSIS") +assert os.path.isdir(FRAMEWORK_DIR) +assert os.path.isdir(CMSIS_DIR) +assert os.path.isdir("buildroot/share/PlatformIO/variants") + +mcu_type = board.get("build.mcu")[:-2] +variant = board.get("build.variant") +series = mcu_type[:7].upper() + "xx" +variant_dir = os.path.join(FRAMEWORK_DIR, "variants", variant) + +source_dir = os.path.join("buildroot/share/PlatformIO/variants", variant) +assert os.path.isdir(source_dir) + +if not os.path.isdir(variant_dir): + os.mkdir(variant_dir) + +for file_name in os.listdir(source_dir): + full_file_name = os.path.join(source_dir, file_name) + if os.path.isfile(full_file_name): + shutil.copy(full_file_name, variant_dir) diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PeripheralPins.c new file mode 100644 index 000000000..4e6a71d80 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PeripheralPins.c @@ -0,0 +1,438 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + * Automatically generated from STM32F407Z(E-G)Tx.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + // {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0 + // {PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + // {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1 + // {PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1 + // {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2 + // {PA_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2 + // {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + // {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3 + {PA_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3 + {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + // {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4 + // {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + // {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + // {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 + // {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + // {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 + // {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 +#endif + {PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + // {PB_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC2_IN9 + // {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + // {PC_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC2_IN10 + {PC_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC3_IN10 + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + // {PC_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC2_IN11 + // {PC_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC3_IN11 + // {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 + {PC_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC2_IN12 + // {PC_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC3_IN12 + // {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 + // {PC_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC2_IN13 + {PC_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC3_IN13 + // {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 + {PC_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC2_IN14 + // {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + {PC_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC2_IN15 +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + // {PF_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC3_IN9 + // {PF_4, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC3_IN14 + // {PF_5, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC3_IN15 + {PF_6, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC3_IN4 + {PF_7, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC3_IN5 + {PF_8, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC3_IN6 + // {PF_9, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC3_IN7 + // {PF_10, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC3_IN8 +#endif + {NC, NP, 0} +}; +#endif + +//*** DAC *** + +#ifdef HAL_DAC_MODULE_ENABLED +const PinMap PinMap_DAC[] = { + {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1 + {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2 + {NC, NP, 0} +}; +#endif + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +const PinMap PinMap_I2C_SDA[] = { + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_11, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, + {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PF_0, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_I2C_MODULE_ENABLED +const PinMap PinMap_I2C_SCL[] = { + {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PF_1, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, +#endif + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +const PinMap PinMap_PWM[] = { + {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1 + {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + // {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2 + {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + // {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 + // {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 + // {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 + // {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PA_5, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + // {PA_6, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 + // {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + // {PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N + // {PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 + // {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + // {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + // {PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N + // {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + // {PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N + // {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 + {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + {PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + {PB_11, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_14, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N + {PB_14, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 1, 0)}, // TIM12_CH1 + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PB_15, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N + {PB_15, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 2, 0)}, // TIM12_CH2 + {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 0)}, // TIM8_CH1 + {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2 + {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + {PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 0)}, // TIM8_CH3 + {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + {PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 4, 0)}, // TIM8_CH4 + {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + {PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + {PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + {PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + {PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PF_6, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 + {PF_7, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 + {PF_8, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1 + {PF_9, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1 +#endif + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_TX[] = { + {PA_0, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)}, + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + // {PC_10, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)}, + {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PC_12, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)}, + {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + // {PG_14, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_RX[] = { + {PA_1, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)}, + {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + // {PC_11, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)}, + {PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PD_2, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)}, + {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + // {PG_9, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PD_12, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PG_8, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PG_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, +#endif + {NC, NP, 0} +}; +#endif + +#ifdef HAL_UART_MODULE_ENABLED +const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PD_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PG_13, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PG_15, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, +#endif + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_SPI_MODULE_ENABLED +const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +//*** CAN *** + +#ifdef HAL_CAN_MODULE_ENABLED +const PinMap PinMap_CAN_RD[] = { + {PA_11, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {PB_5, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {PB_8, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {PB_12, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {PD_0, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {NC, NP, 0} +}; +#endif + +#ifdef HAL_CAN_MODULE_ENABLED +const PinMap PinMap_CAN_TD[] = { + {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {PB_6, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {PB_13, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {PD_1, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)}, + {NC, NP, 0} +}; +#endif + +//*** ETHERNET *** + +#ifdef HAL_ETH_MODULE_ENABLED +const PinMap PinMap_Ethernet[] = { + {PA_0, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_CRS + {PA_1, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_REF_CLK|ETH_RX_CLK + {PA_2, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_MDIO + {PA_3, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_COL + {PA_7, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_CRS_DV|ETH_RX_DV + {PB_0, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_RXD2 + {PB_1, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_RXD3 + {PB_5, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_PPS_OUT + {PB_8, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD3 + {PB_10, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_RX_ER + {PB_11, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TX_EN + {PB_12, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD0 + {PB_13, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD1 + {PC_1, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_MDC + {PC_2, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD2 + {PC_3, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TX_CLK + {PC_4, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_RXD0 + {PC_5, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_RXD1 + {PE_2, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD3 +#if defined(ARDUINO_BLACK_F407ZE) || defined(ARDUINO_BLACK_F407ZG) + {PG_8, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_PPS_OUT + {PG_11, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TX_EN + {PG_13, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD0 + {PG_14, ETH, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF11_ETH)}, // ETH_TXD1 +#endif + {NC, NP, 0} +}; +#endif + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +const PinMap PinMap_USB_OTG_FS[] = { + // {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF + // {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS + // {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID + {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM + {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP + {NC, NP, 0} +}; +#endif + +#ifdef HAL_PCD_MODULE_ENABLED +const PinMap PinMap_USB_OTG_HS[] = { +#ifdef USE_USB_HS_IN_FS + {PA_4, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_SOF + {PB_12, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_ID + {PB_13, USB_OTG_HS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_HS_VBUS + {PB_14, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_DM + {PB_15, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_DP +#else + {PA_3, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D0 + {PA_5, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_CK + {PB_0, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D1 + {PB_1, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D2 + {PB_5, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D7 + {PB_10, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D3 + {PB_11, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D4 + {PB_12, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D5 + {PB_13, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D6 + {PC_0, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_STP + {PC_2, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_DIR + {PC_3, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_NXT +#endif /* USE_USB_HS_IN_FS */ + {NC, NP, 0} +}; +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PinNamesVar.h new file mode 100644 index 000000000..f3c4f0ee0 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/PinNamesVar.h @@ -0,0 +1,50 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 +SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 +SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 +SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 +SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 +SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 +SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 +SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 +SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON +USB_OTG_FS_SOF = PA_8, +USB_OTG_FS_VBUS = PA_9, +USB_OTG_FS_ID = PA_10, +USB_OTG_FS_DM = PA_11, +USB_OTG_FS_DP = PA_12, +USB_OTG_HS_ULPI_D0 = PA_3, +USB_OTG_HS_SOF = PA_4, +USB_OTG_HS_ULPI_CK = PA_5, +USB_OTG_HS_ULPI_D1 = PB_0, +USB_OTG_HS_ULPI_D2 = PB_1, +USB_OTG_HS_ULPI_D7 = PB_5, +USB_OTG_HS_ULPI_D3 = PB_10, +USB_OTG_HS_ULPI_D4 = PB_11, +USB_OTG_HS_ID = PB_12, +USB_OTG_HS_ULPI_D5 = PB_12, +USB_OTG_HS_ULPI_D6 = PB_13, +USB_OTG_HS_VBUS = PB_13, +USB_OTG_HS_DM = PB_14, +USB_OTG_HS_DP = PB_15, +USB_OTG_HS_ULPI_STP = PC_0, +USB_OTG_HS_ULPI_DIR = PC_2, +USB_OTG_HS_ULPI_NXT = PC_3, +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld new file mode 100644 index 000000000..9f411268a --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld @@ -0,0 +1,189 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F407VETx Device with +** 512KByte FLASH, 128KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20020000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K +CCMRAM (rw) : ORIGIN = 0x10000000, LENGTH = 64K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text ALIGN(8): + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata ALIGN(4): + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + _siccmram = LOADADDR(.ccmram); + + /* CCM-RAM section + * + * IMPORTANT NOTE! + * If initialized variables will be placed in this section, + * the startup code needs to be modified to copy the init-values. + */ + .ccmram : + { + . = ALIGN(4); + _sccmram = .; /* create a global symbol at ccmram start */ + *(.ccmram) + *(.ccmram*) + + . = ALIGN(4); + _eccmram = .; /* create a global symbol at ccmram end */ + } >CCMRAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/stm32f4xx_hal_conf.h b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/stm32f4xx_hal_conf.h new file mode 100644 index 000000000..2e111dff8 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/stm32f4xx_hal_conf.h @@ -0,0 +1,481 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_conf.h + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_CONF_H +#define __STM32F4xx_HAL_CONF_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +#define HAL_CRC_MODULE_ENABLED +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +#define HAL_DAC_MODULE_ENABLED +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_PCCARD_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_EXTI_MODULE_ENABLED */ +#define HAL_I2C_MODULE_ENABLED +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +#define HAL_RTC_MODULE_ENABLED +/* #define HAL_SAI_MODULE_ENABLED */ +#define HAL_SD_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +/* #define HAL_UART_MODULE_ENABLED */ +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_PCD_MODULE_ENABLED +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_FMPI2C_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_MMC_MODULE_ENABLED */ + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) +#define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) +#define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) +#define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz +The real value may vary depending on the variations +in voltage and temperature.*/ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) +#define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) +#define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) +#define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the External audio frequency in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define INSTRUCTION_CACHE_ENABLE 1U +#define DATA_CACHE_ENABLE 1U + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848_PHY_ADDRESS Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x000000FFU) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) + +#define PHY_READ_TO ((uint32_t)0x0000FFFFU) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ +#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32f4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32f4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32f4xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32f4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32f4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32f4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED +#include "stm32f4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED +#include "stm32f4xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32f4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED +#include "stm32f4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED +#include "stm32f4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32f4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED +#include "stm32f4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED +#include "stm32f4xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32f4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED +#include "stm32f4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED +#include "stm32f4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED +#include "stm32f4xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED +#include "stm32f4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32f4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED +#include "stm32f4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32f4xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32f4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32f4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32f4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED +#include "stm32f4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32f4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED +#include "stm32f4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED +#include "stm32f4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32f4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32f4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32f4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32f4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32f4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32f4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32f4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32f4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32f4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED +#include "stm32f4xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED +#include "stm32f4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32f4xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_FMPI2C_MODULE_ENABLED +#include "stm32f4xx_hal_fmpi2c.h" +#endif /* HAL_FMPI2C_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED +#include "stm32f4xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED +#include "stm32f4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32f4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED +#include "stm32f4xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t *file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.cpp b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.cpp new file mode 100644 index 000000000..01523224e --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.cpp @@ -0,0 +1,165 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ + +#include "variant.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// Pin number +// This array allows to wrap Arduino pin number(Dx or x) +// to STM32 PinName (PX_n) +const PinName digitalPin[] = { + // Right Side + //Int //Ext + //3V3 //3V3 + //3V3 //3V3 + //BOOT0 //BOOT1 + //GND //GND + //GND //GND + PE_1, PE_0, // D0, D1 + PB_9, PB_8, + PB_7, PB_6, + PB_5, PB_3, + PD_7, PD_6, + PD_5, PD_4, // D10, D11 + PD_3, PD_2, + PD_1, PD_0, + PC_12, PC_11, + PC_10, PA_15, + PA_12, PA_11, // D20, D21 PA_11: USB_DM, PA_12: USB_DP + PA_10, PA_9, + PA_8, PC_9, + PC_8, PC_7, + PC_6, PD_15, + PD_14, PD_13, // D30, D31 + PD_12, PD_11, + PD_10, PD_9, + PD_8, PB_15, + // Left Side + //Ext //Int + //5V //5V + //5V //5V + //3V3 //3V3 + //3V3 //3V3 + //GND //GND + PE_2, PE_3, + PE_4, PE_5, // D40, D41 PE_4: BUT K0, PE_5: BUT K1 + PE_6, PC_13, + PC_0, PC_1, + PC_2, PC_3, + //VREF- //VREF+ + PA_0, PA_1, // PA_0(WK_UP): BUT K_UP) + PA_2, PA_3, // D50, D51 + PA_4, PA_5, + /*PA_6, PA_7,*/ // PA_6, PA_7: Moved to allow contiguous analog pins + PC_4, PC_5, + PB_0, PB_1, + PA_6, PA_7, // PA_6: LED D2, PA_7: LED D3 (active LOW) + PE_7, PE_8, // D60, D61 + PE_9, PE_10, + PE_11, PE_12, + PE_13, PE_14, + PE_15, PB_10, + PB_11, PB_12, // D70, D71 + PB_13, PB_14, + PB_4, +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief System Clock Configuration + * @param None + * @retval None + */ +WEAK void SystemClock_Config(void) +{ + + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_ClkInitTypeDef RCC_ClkInitStruct; + + /**Configure the main internal regulator output voltage + */ + __HAL_RCC_PWR_CLK_ENABLE(); + + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /**Initializes the CPU, AHB and APB busses clocks + */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 8; + RCC_OscInitStruct.PLL.PLLN = 336; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 7; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + _Error_Handler(__FILE__, __LINE__); + } + + /**Initializes the CPU, AHB and APB busses clocks + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) { + _Error_Handler(__FILE__, __LINE__); + } + + /**Configure the Systick interrupt time + */ + HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq() / 1000); + + /**Configure the Systick + */ + HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK); + + /* SysTick_IRQn interrupt configuration */ + HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0); +} + +#ifdef __cplusplus +} +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.h b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.h new file mode 100644 index 000000000..9e383114e --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.h @@ -0,0 +1,219 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +/*---------------------------------------------------------------------------- + * Headers + *----------------------------------------------------------------------------*/ +#include "PeripheralPins.h" + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ +extern const PinName digitalPin[]; +// Right Side +#define PE1 0 +#define PE0 1 +#define PB9 2 +#define PB8 3 +#define PB7 4 +#define PB6 5 +#define PB5 6 +#define PB3 7 +#define PD7 8 +#define PD6 9 +#define PD5 10 +#define PD4 11 +#define PD3 12 +#define PD2 13 +#define PD1 14 +#define PD0 15 +#define PC12 16 +#define PC11 17 +#define PC10 18 +#define PA15 19 +#define PA12 20 // USB_DP +#define PA11 21 // USB_DM +#define PA10 22 +#define PA9 23 +#define PA8 24 +#define PC9 25 +#define PC8 26 +#define PC7 27 +#define PC6 28 +#define PD15 29 +#define PD14 30 +#define PD13 31 +#define PD12 32 +#define PD11 33 +#define PD10 34 +#define PD9 35 +#define PD8 36 +#define PB15 37 +// Left Side +#define PE2 38 +#define PE3 39 +#define PE4 40 // BUT K0 +#define PE5 41 // BUT K1 +#define PE6 42 +#define PC13 43 +#define PC0 44 // A0 +#define PC1 45 // A1 +#define PC2 46 // A2 +#define PC3 47 // A3 +#define PA0 48 // A4/WK_UP: BUT K_UP +#define PA1 49 // A5 +#define PA2 50 // A6 +#define PA3 51 // A7 +#define PA4 52 // A8 +#define PA5 53 // A9 +#define PC4 54 // A10 +#define PC5 55 // A11 +#define PB0 56 // A12 +#define PB1 57 // A13 +#define PA6 58 // LED D2 +#define PA7 59 // LED D3 (active LOW) +#define PE7 60 +#define PE8 61 +#define PE9 62 +#define PE10 63 +#define PE11 64 +#define PE12 65 +#define PE13 66 +#define PE14 67 +#define PE15 68 +#define PB10 69 +#define PB11 70 +#define PB12 71 +#define PB13 72 +#define PB14 73 +#define PB4 74 + +// This must be a literal +#define NUM_DIGITAL_PINS 75 +// This must be a literal with a value less than or equal to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 14 +#define NUM_ANALOG_FIRST 44 + +// Below ADC, DAC and PWM definitions already done in the core +// Could be redefined here if needed +// ADC resolution is 12bits +//#define ADC_RESOLUTION 12 +//#define DACC_RESOLUTION 12 + +// PWM resolution +#define PWM_RESOLUTION 8 +#define PWM_FREQUENCY 20000 +#define PWM_MAX_DUTY_CYCLE 255 + +// On-board LED pin number +#define LED_D2 PA6 +#define LED_D3 PA7 + +// Board specific button +#define BTN_K_UP PA0 + +#define LED_BUILTIN LED_D2 +#define LED_GREEN LED_D2 + +// On-board user button +#define BTN_K0 PE4 +#define BTN_K1 PE3 +#define USER_BTN BTN_K0 + +// Below SPI and I2C definitions already done in the core +// Could be redefined here if differs from the default one +// SPI Definitions +#define PIN_SPI_MOSI PB15 +#define PIN_SPI_MISO PB14 +#define PIN_SPI_SCK PB13 +#define PIN_SPI_SS PB12 +//#define PIN_SPI_SS1 PB0 // W25Q16 (on board flash) + +// I2C Definitions +#define PIN_WIRE_SDA PB7 +#define PIN_WIRE_SCL PB6 + +// Timer Definitions +//Do not use timer used by PWM pins when possible. See PinMap_PWM in PeripheralPins.c +#define TIMER_TONE TIM6 + +// Do not use basic timer: OC is required +#define TIMER_SERVO TIM2 //TODO: advanced-control timers don't work + +// UART Definitions +// Define here Serial instance number to map on Serial generic name +#define SERIAL_UART_INSTANCE 1 //ex: 2 for Serial2 (USART2) +// DEBUG_UART could be redefined to print on another instance than 'Serial' +//#define DEBUG_UART ((USART_TypeDef *) U(S)ARTX) // ex: USART3 +// DEBUG_UART baudrate, default: 9600 if not defined +//#define DEBUG_UART_BAUDRATE x +// DEBUG_UART Tx pin name, default: the first one found in PinMap_UART_TX for DEBUG_UART +//#define DEBUG_PINNAME_TX PX_n // PinName used for TX + +// Default pin used for 'Serial' instance (ex: ST-Link) +// Mandatory for Firmata +#define PIN_SERIAL_RX PA10 +#define PIN_SERIAL_TX PA9 + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial +#define SERIAL_PORT_HARDWARE Serial1 +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */ diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h new file mode 100644 index 000000000..a1b425e40 --- /dev/null +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -0,0 +1,2108 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT -1 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT_2 1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_BLACK_STM32F407VE +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 2 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD +#if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + */ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define POWER_TIMEOUT 30 + #endif + +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 1 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 1 +#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 +#define CHAMBER_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 +#define CHAMBER_MAXTEMP 100 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2208, TMC2208_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC2160, TMC2160_STANDALONE, TMC5130, TMC5130_STANDALONE, + * TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +//#define X_DRIVER_TYPE A4988 +//#define Y_DRIVER_TYPE A4988 +//#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +//#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +// +// Use Junction Deviation instead of traditional Jerk Limiting +// +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH +#if ENABLED(BLTOUCH) + //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed + + /** + * BLTouch V3.0 and newer smart series + * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV. + * If the pin trigger is not detected, first try swapping the black and white wires then toggle this. + */ + //#define BLTOUCH_V3 + #if ENABLED(BLTOUCH_V3) + //#define BLTOUCH_FORCE_5V_MODE + //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE + #endif +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// The number of probes to perform at each point. +// Set to 2 for a fast/slow probe, using the second probe result. +// Set to 3 or more for slow probes, averaging the results. +//#define MULTIPLE_PROBING 2 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 200 +#define Y_BED_SIZE 200 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 200 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +// +#define EEPROM_SETTINGS // Enable for M500 and M501 commands +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Moves the nozzle to the initial position + #define NOZZLE_CLEAN_GOBACK +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +//#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + //#define U8GLIB_SSD1306 + #define U8GLIB_SH1106 +#endif + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +// +// Extensible UI +// +// Enable third-party or vendor customized user interfaces that aren't +// packaged with Marlin. Source code for the user interface will need to +// be placed in "src/lcd/extensible_ui/lib" +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// MKS Robin 320x240 color display +// +//#define MKS_ROBIN_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// CONTROLLER TYPE: Standalone / Serial +// + +// +// LCD for Malyan M200 printers. +// +//#define MALYAN_LCD + +// +// CONTROLLER TYPE: Keypad / Add-on +// + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + #define RGB_LED_R_PIN 34 + #define RGB_LED_G_PIN 43 + #define RGB_LED_B_PIN 35 + #define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +#define NUM_SERVOS 2 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300, 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h new file mode 100644 index 000000000..4a184d243 --- /dev/null +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -0,0 +1,2327 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // this adds an experimental additional term to the heating power, proportional to the extrusion speed. + // if Kc is chosen well, the additional required power due to increased melting should be compensated. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behaviour. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN FAN1_PIN +#define E1_AUTO_FAN_PIN FAN2_PIN +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +//=========================================================================== +//============================ Mechanical Settings ========================== +//=========================================================================== + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES {false, false, false, false} + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if ENABLED(ULTIPANEL) + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define MANUAL_E_MOVES_RELATIVE // Show LCD extruder moves as relative rather than absolute positions + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + +#endif // SDSUPPORT + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +// The hardware watchdog should reset the microcontroller disabling all outputs, +// in case the firmware gets stuck and doesn't do temperature regulation. +#define USE_WATCHDOG + +#if ENABLED(USE_WATCHDOG) + // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on. + // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset. + // However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled. + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 1 : Minimum for A4988, A5984, and LV8729 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 130000 : Maximum for LV8729 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Use software SPI for TMC2130. + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. TMC2208 requires hardware serial. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // TMC2130 only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // TMC2130 only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_LASER_ENABLE +#if ENABLED(SPINDLE_LASER_ENABLE) + + #define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed + #define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop + #define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction + #define SPINDLE_INVERT_DIR false + #define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + + //#define SPEED_POWER_SLOPE 0.3922 + //#define SPEED_POWER_INTERCEPT 0 + //#define SPEED_POWER_MIN 10 + //#define SPEED_POWER_MAX 100 // 0-100% +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behaviour. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behaviour is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h similarity index 100% rename from config/examples/STM32F10/Configuration.h rename to config/examples/STM32/STM32F10/Configuration.h diff --git a/config/examples/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h similarity index 100% rename from config/examples/stm32f103ret6/Configuration.h rename to config/examples/STM32/stm32f103ret6/Configuration.h diff --git a/config/examples/STM32F4/Configuration.h b/config/examples/stm32/STM32F4/Configuration.h similarity index 100% rename from config/examples/STM32F4/Configuration.h rename to config/examples/stm32/STM32F4/Configuration.h diff --git a/platformio.ini b/platformio.ini index e605a3d83..9d3b4cdc0 100644 --- a/platformio.ini +++ b/platformio.ini @@ -307,7 +307,6 @@ framework = arduino board = genericSTM32F103ZE extra_scripts = buildroot/share/PlatformIO/scripts/mks_robin.py build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py - -DSTM32_XL_DENSITY ${common.build_flags} -DSTM32_XL_DENSITY src_filter = ${common.default_src_filter} + @@ -320,6 +319,23 @@ lib_ignore = c1921b4 libf3e TMC26XStepper +# +# STM32F407VET6 with RAMPS-like shield +# 'Black' STM32F407VET6 board - http://wiki.stm32duino.com/index.php?title=STM32F407 +# Shield - https://github.com/jmz52/Hardware +# +[env:black_stm32f407ve] +platform = ststm32 +framework = arduino +board = blackSTM32F407VET6 +extra_scripts = pre:buildroot/share/PlatformIO/scripts/black_stm32f407vet6.py +build_flags = ${common.build_flags} + -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"BLACK_F407VE\" +lib_deps = ${common.lib_deps} +lib_ignore = Adafruit NeoPixel, c1921b4, TMCStepper, TMC26XStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster +src_filter = ${common.default_src_filter} + +monitor_speed = 250000 + # # Teensy 3.5 / 3.6 (ARM Cortex-M4) #