From 19df90622b8be6c6bc2605862edf0fc546b68ef8 Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sat, 21 Mar 2015 15:40:20 -0700 Subject: [PATCH] Include Conditionals.h file in update --- Marlin/Conditionals.h | 405 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 405 insertions(+) create mode 100644 Marlin/Conditionals.h diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h new file mode 100644 index 000000000..fc6d6573e --- /dev/null +++ b/Marlin/Conditionals.h @@ -0,0 +1,405 @@ +/** + * Conditionals.h + * Defines that depend on configuration but are not editable. + */ +#ifndef CONDITIONALS_H + +#ifndef CONFIGURATION_LCD // Get the LCD defines which are needed first + + #define CONFIGURATION_LCD + + #if defined(MAKRPANEL) + #define DOGLCD + #define SDSUPPORT + #define DEFAULT_LCD_CONTRAST 17 + #define ULTIPANEL + #define NEWPANEL + #endif + + #if defined(miniVIKI) || defined(VIKI2) + #define ULTRA_LCD //general LCD support, also 16x2 + #define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) + #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. + + #ifdef miniVIKI + #define DEFAULT_LCD_CONTRAST 95 + #else + #define DEFAULT_LCD_CONTRAST 40 + #endif + + #define ENCODER_PULSES_PER_STEP 4 + #define ENCODER_STEPS_PER_MENU_ITEM 1 + #endif + + #ifdef PANEL_ONE + #define SDSUPPORT + #define ULTIMAKERCONTROLLER + #endif + + #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + #define DOGLCD + #define U8GLIB_ST7920 + #define REPRAP_DISCOUNT_SMART_CONTROLLER + #endif + + #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) + #define ULTIPANEL + #define NEWPANEL + #endif + + #ifdef REPRAPWORLD_KEYPAD + #define ULTIPANEL + #define NEWPANEL + #endif + + #ifdef RA_CONTROL_PANEL + #define LCD_I2C_TYPE_PCA8574 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define ULTIPANEL + #define NEWPANEL + #endif + + /** + * I2C PANELS + */ + + #ifdef LCD_I2C_SAINSMART_YWROBOT + // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home ) + // Make sure it is placed in the Arduino libraries directory. + #define LCD_I2C_TYPE_PCF8575 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define ULTIPANEL + #define NEWPANEL + #endif + + // PANELOLU2 LCD with status LEDs, separate encoder and click inputs + #ifdef LCD_I2C_PANELOLU2 + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) + // Note: The PANELOLU2 encoder click input can either be directly connected to a pin + // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD + + #ifndef ENCODER_PULSES_PER_STEP + #define ENCODER_PULSES_PER_STEP 4 + #endif + + #ifndef ENCODER_STEPS_PER_MENU_ITEM + #define ENCODER_STEPS_PER_MENU_ITEM 1 + #endif + + #ifdef LCD_USE_I2C_BUZZER + #define LCD_FEEDBACK_FREQUENCY_HZ 1000 + #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 + #endif + + #define ULTIPANEL + #define NEWPANEL + #endif + + // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs + #ifdef LCD_I2C_VIKI + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // Note: The pause/stop/resume LCD button pin should be connected to the Arduino + // BTN_ENC pin (or set BTN_ENC to -1 if not used) + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) + #define ULTIPANEL + #define NEWPANEL + #endif + + // Shift register panels + // --------------------- + // 2 wire Non-latching LCD SR from: + // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection + + #ifdef SAV_3DLCD + #define SR_LCD_2W_NL // Non latching 2 wire shiftregister + #define ULTIPANEL + #define NEWPANEL + #endif + + + #ifdef ULTIPANEL + #define NEWPANEL //enable this if you have a click-encoder panel + #define SDSUPPORT + #define ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the DOG graphic display + #define LCD_WIDTH 22 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 20 + #define LCD_HEIGHT 4 + #endif + #else //no panel but just LCD + #ifdef ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display + #define LCD_WIDTH 22 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 16 + #define LCD_HEIGHT 2 + #endif + #endif + #endif + + /** + * Default LCD contrast for dogm-like LCD displays + */ + #if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST) + #define DEFAULT_LCD_CONTRAST 32 + #endif + +#else // CONFIGURATION_LCD + + #define CONDITIONALS_H + + #ifndef AT90USB + #define HardwareSerial_h // trick to disable the standard HWserial + #endif + + #if (ARDUINO >= 100) + #include "Arduino.h" + #else + #include "WProgram.h" + #endif + + #include "pins.h" + + /** + * ENDSTOPPULLUPS + */ + #ifdef ENDSTOPPULLUPS + #ifndef DISABLE_MAX_ENDSTOPS + #define ENDSTOPPULLUP_XMAX + #define ENDSTOPPULLUP_YMAX + #define ENDSTOPPULLUP_ZMAX + #endif + #ifndef DISABLE_MIN_ENDSTOPS + #define ENDSTOPPULLUP_XMIN + #define ENDSTOPPULLUP_YMIN + #define ENDSTOPPULLUP_ZMIN + #endif + #endif + + /** + * Axis lengths + */ + #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS) + #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS) + #define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS) + + /** + * SCARA + */ + #ifdef SCARA + #undef SLOWDOWN + #define QUICK_HOME //SCARA needs Quickhome + #endif + + /** + * AUTOSET LOCATIONS OF LIMIT SWITCHES + * Added by ZetaPhoenix 09-15-2012 + */ + #ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations + #define X_HOME_POS MANUAL_X_HOME_POS + #define Y_HOME_POS MANUAL_Y_HOME_POS + #define Z_HOME_POS MANUAL_Z_HOME_POS + #else //!MANUAL_HOME_POSITIONS – Use home switch positions based on homing direction and travel limits + #ifdef BED_CENTER_AT_0_0 + #define X_HOME_POS X_MAX_LENGTH * X_HOME_DIR * 0.5 + #define Y_HOME_POS Y_MAX_LENGTH * Y_HOME_DIR * 0.5 + #else + #define X_HOME_POS (X_HOME_DIR < 0 ? X_MIN_POS : X_MAX_POS) + #define Y_HOME_POS (Y_HOME_DIR < 0 ? Y_MIN_POS : Y_MAX_POS) + #endif + #define Z_HOME_POS (Z_HOME_DIR < 0 ? Z_MIN_POS : Z_MAX_POS) + #endif //!MANUAL_HOME_POSITIONS + + /** + * Auto Bed Leveling + */ + #ifdef ENABLE_AUTO_BED_LEVELING + // Boundaries for probing based on set limits + #define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #endif + + /** + * MAX_STEP_FREQUENCY differs for TOSHIBA + */ + #ifdef CONFIG_STEPPERS_TOSHIBA + #define MAX_STEP_FREQUENCY 10000 // Max step frequency for Toshiba Stepper Controllers + #else + #define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step) + #endif + + // MS1 MS2 Stepper Driver Microstepping mode table + #define MICROSTEP1 LOW,LOW + #define MICROSTEP2 HIGH,LOW + #define MICROSTEP4 LOW,HIGH + #define MICROSTEP8 HIGH,HIGH + #define MICROSTEP16 HIGH,HIGH + + /** + * Advance calculated values + */ + #ifdef ADVANCE + #define EXTRUSION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159) + #define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS] / EXTRUSION_AREA) + #endif + + #ifdef ULTIPANEL + #undef SDCARDDETECTINVERTED + #endif + + // Power Signal Control Definitions + // By default use ATX definition + #ifndef POWER_SUPPLY + #define POWER_SUPPLY 1 + #endif + // 1 = ATX + #if (POWER_SUPPLY == 1) + #define PS_ON_AWAKE LOW + #define PS_ON_ASLEEP HIGH + #endif + // 2 = X-Box 360 203W + #if (POWER_SUPPLY == 2) + #define PS_ON_AWAKE HIGH + #define PS_ON_ASLEEP LOW + #endif + + /** + * Temp Sensor defines + */ + #if TEMP_SENSOR_0 == -2 + #define HEATER_0_USES_MAX6675 + #elif TEMP_SENSOR_0 == -1 + #define HEATER_0_USES_AD595 + #elif TEMP_SENSOR_0 == 0 + #undef HEATER_0_MINTEMP + #undef HEATER_0_MAXTEMP + #elif TEMP_SENSOR_0 > 0 + #define THERMISTORHEATER_0 TEMP_SENSOR_0 + #define HEATER_0_USES_THERMISTOR + #endif + + #if TEMP_SENSOR_1 == -1 + #define HEATER_1_USES_AD595 + #elif TEMP_SENSOR_1 == 0 + #undef HEATER_1_MINTEMP + #undef HEATER_1_MAXTEMP + #elif TEMP_SENSOR_1 > 0 + #define THERMISTORHEATER_1 TEMP_SENSOR_1 + #define HEATER_1_USES_THERMISTOR + #endif + + #if TEMP_SENSOR_2 == -1 + #define HEATER_2_USES_AD595 + #elif TEMP_SENSOR_2 == 0 + #undef HEATER_2_MINTEMP + #undef HEATER_2_MAXTEMP + #elif TEMP_SENSOR_2 > 0 + #define THERMISTORHEATER_2 TEMP_SENSOR_2 + #define HEATER_2_USES_THERMISTOR + #endif + + #if TEMP_SENSOR_3 == -1 + #define HEATER_3_USES_AD595 + #elif TEMP_SENSOR_3 == 0 + #undef HEATER_3_MINTEMP + #undef HEATER_3_MAXTEMP + #elif TEMP_SENSOR_3 > 0 + #define THERMISTORHEATER_3 TEMP_SENSOR_3 + #define HEATER_3_USES_THERMISTOR + #endif + + #if TEMP_SENSOR_BED == -1 + #define BED_USES_AD595 + #elif TEMP_SENSOR_BED == 0 + #undef BED_MINTEMP + #undef BED_MAXTEMP + #elif TEMP_SENSOR_BED > 0 + #define THERMISTORBED TEMP_SENSOR_BED + #define BED_USES_THERMISTOR + #endif + + /** + * ARRAY_BY_EXTRUDERS based on EXTRUDERS + */ + #if EXTRUDERS > 3 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3, v4 } + #elif EXTRUDERS > 2 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2, v3 } + #elif EXTRUDERS > 1 + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1, v2 } + #else + #define ARRAY_BY_EXTRUDERS(v1, v2, v3, v4) { v1 } + #endif + + /** + * Shorthand for pin tests, for temperature.cpp + */ + #define HAS_TEMP_0 (defined(TEMP_0_PIN) && TEMP_0_PIN >= 0) + #define HAS_TEMP_1 (defined(TEMP_1_PIN) && TEMP_1_PIN >= 0) + #define HAS_TEMP_2 (defined(TEMP_2_PIN) && TEMP_2_PIN >= 0) + #define HAS_TEMP_3 (defined(TEMP_3_PIN) && TEMP_3_PIN >= 0) + #define HAS_TEMP_BED (defined(TEMP_BED_PIN) && TEMP_BED_PIN >= 0) + #define HAS_FILAMENT_SENSOR (defined(FILAMENT_SENSOR) && defined(FILWIDTH_PIN) && FILWIDTH_PIN >= 0) + #define HAS_HEATER_0 (defined(HEATER_0_PIN) && HEATER_0_PIN >= 0) + #define HAS_HEATER_1 (defined(HEATER_1_PIN) && HEATER_1_PIN >= 0) + #define HAS_HEATER_2 (defined(HEATER_2_PIN) && HEATER_2_PIN >= 0) + #define HAS_HEATER_3 (defined(HEATER_3_PIN) && HEATER_3_PIN >= 0) + #define HAS_HEATER_BED (defined(HEATER_BED_PIN) && HEATER_BED_PIN >= 0) + #define HAS_AUTO_FAN_0 (defined(EXTRUDER_0_AUTO_FAN_PIN) && EXTRUDER_0_AUTO_FAN_PIN >= 0) + #define HAS_AUTO_FAN_1 (defined(EXTRUDER_1_AUTO_FAN_PIN) && EXTRUDER_1_AUTO_FAN_PIN >= 0) + #define HAS_AUTO_FAN_2 (defined(EXTRUDER_2_AUTO_FAN_PIN) && EXTRUDER_2_AUTO_FAN_PIN >= 0) + #define HAS_AUTO_FAN_3 (defined(EXTRUDER_3_AUTO_FAN_PIN) && EXTRUDER_3_AUTO_FAN_PIN >= 0) + #define HAS_AUTO_FAN HAS_AUTO_FAN_0 || HAS_AUTO_FAN_1 || HAS_AUTO_FAN_2 || HAS_AUTO_FAN_3 + #define HAS_FAN (defined(FAN_PIN) && FAN_PIN >= 0) + + /** + * Helper Macros for heaters and extruder fan + */ + #define WRITE_HEATER_0P(v) WRITE(HEATER_0_PIN, v) + #if EXTRUDERS > 1 || defined(HEATERS_PARALLEL) + #define WRITE_HEATER_1(v) WRITE(HEATER_1_PIN, v) + #if EXTRUDERS > 2 + #define WRITE_HEATER_2(v) WRITE(HEATER_2_PIN, v) + #if EXTRUDERS > 3 + #define WRITE_HEATER_3(v) WRITE(HEATER_3_PIN, v) + #endif + #endif + #endif + #ifdef HEATERS_PARALLEL + #define WRITE_HEATER_0(v) { WRITE_HEATER_0P(v); WRITE_HEATER_1(v); } + #else + #define WRITE_HEATER_0(v) WRITE_HEATER_0P(v) + #endif + #if HAS_HEATER_BED + #define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, v) + #endif + #if HAS_FAN + #define WRITE_FAN(v) WRITE(FAN_PIN, v) + #endif + + /** + * Sampling period of the temperature routine + * This override comes originally from temperature.cpp + * The Configuration.h option is basically ignored. + */ + #ifdef PID_dT + #undef PID_dT + #endif + #define PID_dT ((OVERSAMPLENR * 12.0)/(F_CPU / 64.0 / 256.0)) + + +#endif //CONFIGURATION_LCD +#endif //CONDITIONALS_H