From 0f3b7d5575d6fa17ddf56b8ec5d6b51d3490dbee Mon Sep 17 00:00:00 2001 From: Scott Lahteine Date: Sat, 7 Mar 2015 01:07:40 -0800 Subject: [PATCH] Update annotated configurations - Also update base configs --- Marlin/Configuration.h | 27 ++-- Marlin/Configuration_adv.h | 4 +- Marlin/configurator/config/Configuration.h | 148 ++++++++++-------- .../configurator/config/Configuration_adv.h | 5 + 4 files changed, 102 insertions(+), 82 deletions(-) diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index f3723de18..91e1ecf71 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -346,13 +346,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define DISABLE_E false // For all extruders #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true -#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false -#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false -#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false -#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false +#define INVERT_E0_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E1_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E2_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E3_DIR false // Direct drive extruder v9: true. Geared extruder: false // ENDSTOP SETTINGS: // Sets direction of endstops when homing; 1=MAX, -1=MIN @@ -364,12 +365,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. // Travel limits after homing (units are in mm) -#define X_MAX_POS 205 #define X_MIN_POS 0 -#define Y_MAX_POS 205 #define Y_MIN_POS 0 -#define Z_MAX_POS 200 #define Z_MIN_POS 0 +#define X_MAX_POS 205 +#define Y_MAX_POS 205 +#define Z_MAX_POS 200 #define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS) #define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS) @@ -475,12 +476,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used //#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) -//Manual homing switch locations: +// Manual homing switch locations: // For deltabots this means top and center of the Cartesian print volume. -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0 -//#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. +#ifdef MANUAL_HOME_POSITIONS + #define MANUAL_X_HOME_POS 0 + #define MANUAL_Y_HOME_POS 0 + #define MANUAL_Z_HOME_POS 0 + //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. +#endif //// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index f2b312441..32cabbd5f 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -285,8 +285,8 @@ //=========================================================================== #define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly -#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value -#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value +#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value +#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value //#define ENCODER_RATE_MULTIPLIER_DEBUG // If defined, output the encoder steps per second value //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index 272a0eb66..ddfbe0174 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -8,7 +8,7 @@ //=========================================================================== /* Here are some standard links for getting your machine calibrated: - * http://reprap.org/wiki/Calibration + * http://reprap.org/wiki/Calibration * http://youtu.be/wAL9d7FgInk * http://calculator.josefprusa.cz * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide @@ -127,10 +127,15 @@ Here are some standard links for getting your machine calibrated: // 1010 is Pt1000 with 1k pullup (non standard) // 147 is Pt100 with 4k7 pullup // 110 is Pt100 with 1k pullup (non standard) -// :{ 0: "Not used", 4: "10k !! do not use for a hotend. Bad resolution at high temp. !!", 1: "100k / 4.7k - EPCOS", 51: "100k / 1k - EPCOS", 6: "100k / 4.7k EPCOS - Not as accurate as Table 1", 5: "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 7: "100k / 4.7k Honeywell 135-104LAG-J01", 71: "100k / 4.7k Honeywell 135-104LAF-J01", 8: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", 9: "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", 10: "100k / 4.7k RS 198-961", 11: "100k / 4.7k beta 3950 1%", 12: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", 13: "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", 60: "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", 55: "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 2: "200k / 4.7k - ATC Semitec 204GT-2", 52: "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", 3: "Mendel-parts / 4.7k", 1047: "Pt1000 / 4.7k", 1010: "Pt1000 / 1k (non standard)", 20: "PT100 (Ultimainboard V2.x)", 147: "Pt100 / 4.7k", 110: "Pt100 / 1k (non-standard)" } +// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below. +// Use it for Testing or Development purposes. NEVER for production machine. +// #define DUMMY_THERMISTOR_998_VALUE 25 +// #define DUMMY_THERMISTOR_999_VALUE 100 +// :{ 0: "Not used", 4: "10k !! do not use for a hotend. Bad resolution at high temp. !!", 1: "100k / 4.7k - EPCOS", 51: "100k / 1k - EPCOS", 6: "100k / 4.7k EPCOS - Not as accurate as Table 1", 5: "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 7: "100k / 4.7k Honeywell 135-104LAG-J01", 71: "100k / 4.7k Honeywell 135-104LAF-J01", 8: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", 9: "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", 10: "100k / 4.7k RS 198-961", 11: "100k / 4.7k beta 3950 1%", 12: "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", 13: "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", 60: "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", 55: "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", 2: "200k / 4.7k - ATC Semitec 204GT-2", 52: "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", 3: "Mendel-parts / 4.7k", 1047: "Pt1000 / 4.7k", 1010: "Pt1000 / 1k (non standard)", 20: "PT100 (Ultimainboard V2.x)", 147: "Pt100 / 4.7k", 110: "Pt100 / 1k (non-standard)", 998: "Dummy 1", 999: "Dummy 2" } #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 -1 #define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 #define TEMP_SENSOR_BED 0 // This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. @@ -148,6 +153,7 @@ Here are some standard links for getting your machine calibrated: #define HEATER_0_MINTEMP 5 #define HEATER_1_MINTEMP 5 #define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 #define BED_MINTEMP 5 // When temperature exceeds max temp, your heater will be switched off. @@ -156,6 +162,7 @@ Here are some standard links for getting your machine calibrated: #define HEATER_0_MAXTEMP 275 #define HEATER_1_MAXTEMP 275 #define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 #define BED_MAXTEMP 150 // If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the @@ -300,9 +307,12 @@ your extruder heater takes 2 minutes to hit the target on heating. // @section machine -// Uncomment the following line to enable CoreXY kinematics +// Uncomment this option to enable CoreXY kinematics // #define COREXY +// Enable this option for Toshiba steppers +// #define CONFIG_STEPPERS_TOSHIBA + // @section homing // coarse Endstop Settings @@ -337,13 +347,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS -// @section hidden - -// Disable max endstops for compatibility with endstop checking routine -#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS) - #define DISABLE_MAX_ENDSTOPS -#endif - // @section machine // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 @@ -366,17 +369,17 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR true // Mendel: false -#define INVERT_Y_DIR false // Mendel: true -#define INVERT_Z_DIR true // Mendel: false +#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true +#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false +#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true // @section extruder // For direct drive extruder v9 set to true, for geared extruder set to false. -#define INVERT_E0_DIR false -#define INVERT_E1_DIR false -#define INVERT_E2_DIR false -#define INVERT_E3_DIR false +#define INVERT_E0_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E1_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E2_DIR false // Direct drive extruder v9: true. Geared extruder: false +#define INVERT_E3_DIR false // Direct drive extruder v9: true. Geared extruder: false // @section homing @@ -418,40 +421,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #ifdef ENABLE_AUTO_BED_LEVELING -// There are 2 different ways to pick the X and Y locations to probe: - -// - "grid" mode -// Probe every point in a rectangular grid -// You must specify the rectangle, and the density of sample points -// This mode is preferred because there are more measurements. -// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive - -// - "3-point" mode -// Probe 3 arbitrary points on the bed (that aren't colinear) -// You must specify the X & Y coordinates of all 3 points - + // There are 2 different ways to specify probing locations + // + // - "grid" mode + // Probe several points in a rectangular grid. + // You specify the rectangle and the density of sample points. + // This mode is preferred because there are more measurements. + // + // - "3-point" mode + // Probe 3 arbitrary points on the bed (that aren't colinear) + // You specify the XY coordinates of all 3 points. + + // Enable this to sample the bed in a grid (least squares solution) + // Note: this feature generates 10KB extra code size #define AUTO_BED_LEVELING_GRID - // with AUTO_BED_LEVELING_GRID, the bed is sampled in a - // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid - // and least squares solution is calculated - // Note: this feature occupies 10'206 byte + #ifdef AUTO_BED_LEVELING_GRID - // set the rectangle in which to probe + // The edges of the rectangle in which to probe #define LEFT_PROBE_BED_POSITION 15 #define RIGHT_PROBE_BED_POSITION 170 - #define BACK_PROBE_BED_POSITION 180 #define FRONT_PROBE_BED_POSITION 20 + #define BACK_PROBE_BED_POSITION 170 - // set the number of grid points per dimension - // I wouldn't see a reason to go above 3 (=9 probing points on the bed) + // Set the number of grid points per dimension + // You probably don't need more than 3 (squared=9) #define AUTO_BED_LEVELING_GRID_POINTS 2 - #else // not AUTO_BED_LEVELING_GRID - // with no grid, just probe 3 arbitrary points. A simple cross-product - // is used to esimate the plane of the print bed + #else // !AUTO_BED_LEVELING_GRID + // Arbitrary points to probe. A simple cross-product + // is used to estimate the plane of the bed. #define ABL_PROBE_PT_1_X 15 #define ABL_PROBE_PT_1_Y 180 #define ABL_PROBE_PT_2_X 15 @@ -462,11 +463,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #endif // AUTO_BED_LEVELING_GRID - // these are the offsets to the probe relative to the extruder tip (Hotend - Probe) + // Offsets to the probe relative to the extruder tip (Hotend - Probe) // X and Y offsets must be integers - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 + #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right + #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind + #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!) #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance. // Be sure you have this distance over your Z_MAX_POS in case @@ -503,29 +504,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #endif - #ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range - #if X_PROBE_OFFSET_FROM_EXTRUDER < 0 - #if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION)) - #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS" - #endif - #else - #if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION)) - #error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS" - #endif - #endif - #if Y_PROBE_OFFSET_FROM_EXTRUDER < 0 - #if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION)) - #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS" - #endif - #else - #if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION)) - #error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS" - #endif - #endif - - - #endif - #endif // ENABLE_AUTO_BED_LEVELING @@ -609,9 +587,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define ABS_PREHEAT_HPB_TEMP 100 #define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 +//==============================LCD and SD support============================= // @section lcd -//LCD and SD support +// Define your display language below. Replace (en) with your language code and uncomment. +// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu +// See also language.h +//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) // Character based displays can have different extended charsets. #define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°" @@ -629,10 +611,20 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +//#define PANEL_ONE + // The MaKr3d Makr-Panel with graphic controller and SD support // http://reprap.org/wiki/MaKr3d_MaKrPanel //#define MAKRPANEL +// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD +// http://panucatt.com +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define VIKI2 +//#define miniVIKI + // The RepRapDiscount Smart Controller (white PCB) // http://reprap.org/wiki/RepRapDiscount_Smart_Controller //#define REPRAP_DISCOUNT_SMART_CONTROLLER @@ -668,6 +660,26 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of #define DEFAULT_LCD_CONTRAST 17 #endif +#if defined(miniVIKI) || defined(VIKI2) + #define ULTRA_LCD //general LCD support, also 16x2 + #define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) + #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. + + #ifdef miniVIKI + #define DEFAULT_LCD_CONTRAST 95 + #else + #define DEFAULT_LCD_CONTRAST 40 + #endif + + #define ENCODER_PULSES_PER_STEP 4 + #define ENCODER_STEPS_PER_MENU_ITEM 1 +#endif + +#if defined (PANEL_ONE) + #define SDSUPPORT + #define ULTIMAKERCONTROLLER +#endif + #if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define DOGLCD #define U8GLIB_ST7920 diff --git a/Marlin/configurator/config/Configuration_adv.h b/Marlin/configurator/config/Configuration_adv.h index a8ce58768..00722c142 100644 --- a/Marlin/configurator/config/Configuration_adv.h +++ b/Marlin/configurator/config/Configuration_adv.h @@ -312,6 +312,11 @@ //=============================Additional Features=========================== //=========================================================================== +#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly +#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value +#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value +//#define ENCODER_RATE_MULTIPLIER_DEBUG // If defined, output the encoder steps per second value + //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ #define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again